Emerson Rosemount 3051 Bedienungsanleitung

Quick Start Guide

00825-0100-5007, Rev DC

June2023

Rosemount™ 3051 Pressure

Transmitter

Contents

About this guide .......................................................................................................................... 3

System readiness......................................................................................................................... 5

Transmitter installation...............................................................................................................7

Safety instrumented systems installation...............................................................................21

Product certifications................................................................................................................ 22

Quick Start Guide June2023

2 Emerson.com/Rosemount

1 About this guide

This guide provides basic guidelines for Rosemount 3051 Pressure

Transmitters. It does not provide instructions for configuration,

diagnostics, maintenance, service, troubleshooting, Explosion-proof,

Flameproof, or intrinsically safe (I.S.) installations. Refer to

Rosemount 3051 Reference Manual for more instructions. This guide

is also available electronically at Emerson.com/Rosemount.

1.1 Safety messages

WARNING

Explosions

Explosions could result in death or serious injury.

Installation of device in an explosive environment must be in

accordance with appropriate local, national, and international

standards, codes, and practices. Review the approvals section of

the Rosemount 3051 Reference Manual for any restrictions

associated with a safe installation.

In an explosion-proof/flameproof installation, do not remove the

transmitter covers when power is applied to the unit.

Process leaks

Process leaks may cause harm or result in death.

To avoid process leaks, only use the O-ring designed to seal with the

corresponding flange adapter.

Electrical shock

Electrical shock can result in death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

June2023 Quick Start Guide

Quick Start Guide 3

WARNING

Conduit/cable entries

Unless otherwise marked, the conduit/cable entries in the

housing enclosure use a ½–14 NPT form. Only use plugs,

adapters, glands, or conduit with a compatible thread form when

closing these entries.

Entries marked M20 are M20 x 1.5 thread form. On devices with

multiple conduit entries, all entries will have the same thread

form.

When installing in a hazardous location, use only appropriately

listed or Ex certified plugs, glands, or adapters in cable/conduit

entries.

Physical access

Unauthorized personnel may potentially cause significant damage to

and/or misconfiguration of end users’ equipment. This could be

intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access by

unauthorized personnel to protect end users’ assets. This is true for

all systems used within the facility.

Quick Start Guide June2023

4 Emerson.com/Rosemount

2 System readiness

Confirm HART revision capability

•If using HART-based control or asset management systems,

confirm the HART capability of those systems prior to transmitter

installation. Not all systems are capable of communicating with

HART Revision 7. This transmitter can be configured for either

HART Revision 5 or 7.

•For instructions on how to change the HART revision of your

transmitter, see Switch HART revision mode.

2.1 Confirm correct device driver

•Verify the latest device driver (DD/DTM™) is loaded on your

systems to ensure proper communications.

•Download the latest device driver at Emerson.com or

Fieldcommgroup.org.

Rosemount 3051 device revisions and drivers

Table 2-1 provides the information necessary to ensure you have the

correct device driver and documentation for your device.

Table 2-1: Rosemount 3051 with 4-20 mA HART Protocol Device Revisions

and Files

Releas

e date

Device identification Device driver

identification

Review

instruction

Review

functionalit

NAMUR

hardwar

revision

(1)

(1) HART

softwar

revision

(2)

HART

universa

revision

Device

revisio

(3)

Rosemount

2088,

2090P, and

2090F

Pressure

transmitter

Change

description

Aug-16 1.1.xx 1.0.x

3 7 10 with HART

and 1–5 Vdc

Low Power

Protocol

Reference

Manual



with 4–20

mA HART

and 1–5 Vdc

Low Power

Protocol

(4)

5 9

Jan-13 N/A 1.0.x

1 7 10 (5)

5 9

June2023 Quick Start Guide

Quick Start Guide 5

Table 2-1: Rosemount 3051 with 4-20 mA HART Protocol Device Revisions

and Files

(continued)

Releas

e date

Device identification Device driver

identification

Review

instruction

Review

functionalit

NAMUR

hardwar

revision

(1)

(1) HART

softwar

revision

(2)

HART

universa

revision

Device

revisio

(3)

Rosemount

2088,

2090P, and

2090F

Pressure

transmitter

Change

description

Jan-98 N/A N/A 178 5 3 Reference

Manual

N/A

(1) NAMUR revision is located on the hardware tag of the device. Differences in level

3 changes, signified above by xx, represent minor product changes as defined

per NE53. Compatibility and functionality are preserved and product can be used

interchangeably.

(2) HART software revision can be read using a HART capable configuration tool. Value

shown is minimum revision that could correspond to NAMUR revisions.

(3) Device Driver file names use Device and DD Revision, e.g. 10_01. HART Protocol

is designed to enable legacy device driver revisions to continue to communicate

with new HART devices. To access new functionality, the new Device Driver must be

downloaded. It is recommended to download new Device Driver files to ensure full

functionality.

(4) HART revision 5 and 7 Selectable, local operator interface (LOI), scaled variable,

configurable alarms, and expanded engineering units.

(5) Rosemount 3051G Pressure Transmitter updated electronics hardware design.

Intrinsic Safety temperature classification change.

Quick Start Guide June2023

6 Emerson.com/Rosemount

3 Transmitter installation

3.1 Mount the transmitter

3.1.1 Liquid applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the drain/vent valves are

oriented upward.

Figure 3-1: Coplanar and In-line Liquid Applications

Coplanar In-line

Flow

June2023 Quick Start Guide

Quick Start Guide 7

3.1.2 Gas applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Figure 3-2: Coplanar and In-line Gas Applications

Coplanar In-line

Flow

Quick Start Guide June2023

8 Emerson.com/Rosemount

3.1.3 Steam applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Figure 3-3: Coplanar and In-line Steam Applications

Coplanar In-line

Flow

Figure 3-4: Panel and Pipe Mounting

*5/6 x 1½ panel bolts are customer supplied

June2023 Quick Start Guide

Quick Start Guide 9

3.1.4 Bolting considerations

If the transmitter installation requires assembly of the process

flanges, manifolds, or flange adapters, follow the assembly

guidelines to ensure a tight seal for optimal performance

characteristics of the transmitters. Use only bolts supplied with the

transmitter or sold by Emerson as spare parts. Figure 3-5 illustrates

common transmitter assemblies with the bolt length required for

proper transmitter assembly.

Figure 3-5: Common Transmitter Assemblies

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and

flange adapters

Bolts are typically carbon steel (CS) or stainless steel (SST). Confirm

the material by viewing the markings on the head of the bolt and

referencing Table 3-1. If bolt material is not shown in Table 2-1,

contact a local Emerson representative for more information.

Use the following bolt installation procedure:

Procedure

1. CS bolts do not require lubrication and the SST bolts are

coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either

type of bolt.

2. Finger-tighten the bolts.

Quick Start Guide June2023

10 Emerson.com/Rosemount

Andere Handbücher für Rosemount 3051

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 1066 Bedienungsanleitung

Emerson

Emerson Rosemount 2090P Bedienungsanleitung

Emerson

Emerson Rosemount 1066 Bedienungsanleitung

Emerson

Emerson Rosemount Analytical HART 5081-A-HT Bedienungsanleitung

Emerson

Emerson MicroMotion FOUNDATION 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051 CF Series Bedienungsanleitung

Emerson

Emerson MAS 2600 Bedienungsanleitung

Emerson

Emerson Micro Motion 9739 MVD Kurzanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 5400 Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Rosemount 708 Bedienungsanleitung

Emerson

Emerson Rosemount 3308 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 1208A Bedienungsanleitung

Emerson

Emerson MICRO MOTION 2700 Kurzanleitung

Emerson

Emerson Micro Motion 800 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Micro Motion 3700 Bedienungsanleitung

Emerson

Emerson Rosemount OCX 8800 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 1208A Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung