Emerson Rosemount 3144P Bedienungsanleitung

Quick Start Guide

00825-0100-4021, Rev. JB

April 2015

Rosemount 3144P Temperature

Transmitter with HART®Protocol

April 2015

Quick Start Guide

NOTICE

This guide provides basic guidelines for the Rosemount 3144P. It does not provide instructions for detailed

configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flameproof, or

intrinsically safe (I.S.) installations. Refer to the 3144P reference manual (document number

00809-0100-4021) for more instruction. The manual and this guide are also available electronically on

www.emersonprocess.com.

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate

local, national, and international standards, codes, and practices. Please review the approvals section of

this manual for any restrictions associated with a safe installation,

Process leaks may cause harm or result in death.

Install and tighten thermowells or sensors before applying pressure.

Do not remove the thermowell while in operation.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

The conduit/cable entries in the transmitter housing use a 1/2-14 NPT thread form.

When installing in a Hazardous Location, use only appropriately listed or Ex certified plugs, glands, or

adapters in cable/conduit entries.

Contents

System readiness . . . . . . . . . . . . . . . . . . . . . . . . . 3

Verify configuration . . . . . . . . . . . . . . . . . . . . . . . 3

Set the switches . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mount the transmitter. . . . . . . . . . . . . . . . . . . . . 6

Wire and apply power . . . . . . . . . . . . . . . . . . . . . 7

Perform a loop test . . . . . . . . . . . . . . . . . . . . . . . 11

Safety Instrumented System (SIS) . . . . . . . . . .12

Product Certifications . . . . . . . . . . . . . . . . . . . .13

Quick Start Guide

April 2015

Step 1: System readiness

Confirm HART revision capability

If using HART based control or asset management systems, please confirm

the HART capability of those systems prior to transmitter installation. Not all

systems are capable of communicating with HART Revision 7 protocol. This

transmitter can be configured for either HART Revision 5 or 7.

For instructions on how to change the HART revision of your transmitter, refer

to page 4.

Step 2: Verify configuration

The Rosemount 3144P communicates using a Field Communicator

(communication requires a loop resistance between 250 and 1100 ohms) or AMS

Device Manager. Do not operate when power is below 12 Vdc at the transmitter

terminal. Refer to the 3144P Reference Manual (document number

00809-0100-4021) and Field Communicator Reference Manual (document

number 00809-0100-4276) for more information.

Update the Field Communicator software

The latest Field Communicator Field Device Revision Dev v5 or v6, DD v1 or

greater is required to fully communicate with the 3144P. The Device Descriptors

are available with new communicators at www.emersonprocess.com or can be

loaded into existing communicators at any Emerson Process Management

Service Center.

The Device Descriptors are as follows:

Device in HART 5 mode: Device v5 DD v1

Device in HART 7 mode: Device v6 DD v1

Perform the following steps to determine if an upgrade is required. Refer to

Figure 1 on page -4.

1. Connect the sensor (see the wiring diagram located on the inside of the

housing cover).

2. Connect the bench power supply to the power terminals (“+” or “–”).

3. Connect a Field Communicator to the loop across a loop resistor or at the

power/signal terminals on the transmitter.

Software

release date

Identify device Field device driver Review instructions

NAMURsoftware

revision

HART software

revision

HART universal

revision

Device

revision

Manual document

number

Mar-2012 1.1.1 2

7 6

00809-0100-4021

5 5

Feb-2007 N/A 1 5 4 00809-0100-4021

April 2015

Quick Start Guide

4. The following message will appear if the communicator has a previous version

of the device descriptors (DDs):

NOTICE: Upgrade the communicator software to access new XMTR functions.

Continue with old description?

Note

If this notice does not appear, the latest DD is installed.

If the latest version is not available, the communicator will communicate

properly, but when the transmitter is configured some new capabilities may not

be visible.

To prevent this from happening, upgrade to the latest DD or answer NO to the

question and default to the generic transmitter functionality.

Figure 1. Connecting a Communicator to a Bench Loop

Switch HART revision mode

If the HART configuration tool is not capable of communicating with HART

Revision 7, the 3144P will load a Generic Menu with limited capability. The

following procedures will switch the HART revision mode from the Generic Menu:

1. Manual Setup > Device Information > Identification > Message.

a. To change to HART Revision 5, Enter: “HART5” in the Message field

b. To change to HART Revision 7, Enter: “HART7” in the Message field

Function HART 5 fast keys HART 7 fast keys

2-wire Offset Sensor 1 2, 2, 1, 5 2, 2, 1, 6

2-wire Offset Sensor 2 2, 2, 2, 5 2, 2, 2, 6

Alarm Values 2, 2, 5, 6 2, 2, 5, 6

Analog Calibration 3, 4, 5 3, 4, 5

Analog Output 2, 2, 5 2, 2, 5

Average Temperature Setup 2, 2, 3, 3 2, 2, 3, 3

Burst Mode N/A 2, 2, 8, 4

Comm Status N/A 1, 2

Configure additional messages N/A 2, 2, 8, 4, 7

Configure Hot Backup 2, 2, 4, 1, 3 2, 2, 4, 1, 3

Date 2, 2, 7, 1, 2 2, 2, 7, 1, 3

Descriptor 2, 2, 7, 1, 3 2, 2, 7, 1, 4

Device Information 2, 2, 7, 1 2, 2, 7, 1

Differential Temperature Setup 2, 2, 3, 1 2, 2, 3, 1

250  ≤RL ≤1100 

Power Supply

Power/Signal Terminals

Quick Start Guide

April 2015

Step 3: Set the switches

Switch HART revision mode

The 3144P comes with hardware switches to configure alarms and lock the

device. Use the following procedure to set the switches.

Without a LCD display

1. Set the loop to manual (if applicable) and disconnect the power.

2. Remove the electronics housing cover.

3. Set the alarm and security switches to the desired position. Reattach housing

cover.

4. Apply power and set the loop to automatic control.

Filter 50/60 Hz 2, 2, 7, 5, 1 2, 2, 7, 5, 1

Find Device N/A 3, 4, 6, 2

First Good Temperature Setup 2, 2, 3, 2 2, 2, 3, 2

Hardware Revision 1, 8, 2, 3 1, 11, 2, 3

HART Lock N/A 2, 2, 9, 2

Intermittent Sensor Detect 2, 2, 7, 5, 2 2, 2, 7, 5, 2

Lock Status N/A 1, 11, 3, 7

Long Tag N/A 2, 2, 7, 2

Loop Test 3, 5, 1 3, 5, 1

LRV (Lower Range Value) 2, 2, 5, 5, 3 2, 2, 5, 5, 3

Message 2, 2, 7, 1, 4 2, 2, 7, 1, 5

Open Sensor Holdoff 2, 2, 7, 4 2, 2, 7, 4

Percent Range 2, 2, 5, 4 2, 2, 5, 4

Sensor 1 Configuration 2, 2, 1 2, 2, 2

Sensor 1 Serial Number 2, 2, 1, 7 2, 2, 1, 8

Sensor 1 Setup 2, 2, 1 2, 2, 1

Sensor 1 Status N/A 2, 2, 1, 2

Sensor 1 Type 2, 2, 1, 2 2, 2, 1, 3

Sensor 1 Unit 2, 2, 1, 4 2, 2, 1, 5

Sensor 2 Configuration 2, 2, 2 2, 2, 2

Sensor 2 Serial Number 2, 2, 2, 7 2, 2, 2, 8

Sensor 2 Setup 2, 2, 2 2, 2, 2

Sensor 2 Status N/A 2, 2, 2, 2

Sensor 2 Type 2, 2, 2, 2 2, 2, 2, 3

Sensor 2 Unit 2, 2, 2, 4 2, 2, 2, 5

Sensor Drift Alert 2, 2, 4, 2 2, 2, 4, 2

Simulate Device Variables N/A 3, 5, 2

Software Revision 1, 8, 2, 4 1, 11, 2, 4

Tag 2, 2, 7, 1, 1 2, 2, 7, 1, 1

Terminal Temperature Units 2, 2, 7, 3 2, 2, 7, 3

URV (Upper Range Value) 2, 2, 5, 5, 2 2, 2, 5, 5, 2

Variable Mapping 2, 2, 8, 5 2, 2, 8, 5

Thermocouple Diagnostic 2, 1, 7, 1 2, 1, 7, 1

Min/Max Tracking 2, 1, 7, 2 2, 1, 7, 2

Function HART 5 fast keys HART 7 fast keys

April 2015

Quick Start Guide

With a LCD display

1. Set the loop to manual (if applicable) and disconnect the power.

2. Remove the electronics housing cover.

3. Unscrew the LCD display screws and slide the meter straight off.

4. Set the alarm and security switches to the desired position.

5. Reattach the LCD display and electronics housing cover (consider LCD display

orientation – rotate in 90 degree increments).

6. Apply power and set the loop to automatic control.

Step 4: Mount the transmitter

Mount the transmitter at a high point in the conduit run to prevent moisture from

draining into the transmitter housing.

Typical field mount installation

1. Mount the thermowell to the process container wall. Install and tighten

thermowells. Perform a leak check.

2. Attach any necessary unions, couplings, and extension fittings. Seal the fitting

threads with an approved thread sealant, such as silicone or PTFE tape (if

required).

3. Screw the sensor into the thermowell or directly into the process (depending

on installation requirements).

4. Verify all sealing requirements.

5. Attach the transmitter to the thermowell/sensor assembly. Seal all threads

with an approved thread sealant, such as silicone or PTFE tape (if required).

6. Install field wiring conduit into the open transmitter conduit entry (for remote

mounting) and feed wires into the transmitter housing.

7. Pull the field wiring leads into the terminal side of the housing.

8. Attach the sensor leads to the transmitter sensor terminals (the wiring

diagram is located inside the housing cover).

9. Attach and tighten both transmitter covers.

A. Thermowell

B. Extension (Nipple)

C. Union or Coupling

D. Conduit for Field Wiring (dc power)

E. Extension Fitting Length

Quick Start Guide

April 2015

Typical remote mount installation

1. Mount the thermowell to the process container wall. Install and tighten

thermowells. Perform a leak check.

2. Attach a connection head to the thermowell.

3. Insert sensor into the thermowell and wire the sensor to the connection head

(the wiring diagram is located inside the connection head).

4. Mount the transmitter to a 2-in. (50 mm) pipe or a panel using one of the

optional mounting bracket (B4 bracket is shown below).

5. Attach cable glands to the shielded cable running from the connection head

to the transmitter conduit entry.

6. Run the shielded cable from the opposite conduit entry on the transmitter

back to the control room.

7. Insert shielded cable leads through the cable entries into the connection

head/transmitter. Connect and tighten cable glands.

8. Connect the shielded cable leads to the connection head terminals (located

inside the connection head) and to the sensor wiring terminals (located inside

the transmitter housing).

A. Cable Gland

B. Shielded Cable from Sensor to Transmitter

C. Shielded Cable from Transmitter to Control Room

D. 2-in. (50mm) pipe

E. B4 Mounting Bracket

Step 5: Wire and apply power

Wire the transmitter

Wiring diagrams are located inside the terminal block cover. See 3144P

Single-sensor below.

3144P Single-sensor

* Transmitter must be configured for a 3-wire RTD in order to recognize an RTD with a compensation loop.

** Rosemount provides 4-wire sensors for all single-element RTDs. You can use these RTDs in 3-wire

configurations by leaving the unneeded leads disconnected and insulated with electrical tape.

4-wire RTD

andOhms T/Cs and

Millivolts RTD with

Compensation

2-wire RTD

and Ohms 3-wire RTD

and Ohms**

April 2015

Quick Start Guide

Power the transmitter

An external power supply is required to operate the transmitter.

1. Remove the terminal block cover.

2. Connect the positive power lead to the “+” terminal.

3. Connect the negative power lead to the “–” terminal.

4. Tighten the terminal screws.

5. Reattach and tighten the cover.

6. Apply power.

3144P Dual-sensor

* Rosemount provides 4-wire sensors for all single-element RTDs. You can use these RTDs in 3-wire

configurations by leaving the unneeded leads disconnected and insulated with electrical tape.

ΔT/Hot

Backup/Dual

Sensor with 2

RTDs*

ΔT/Hot

Backup/Dual

Sensor with 2

Thermocouples*

ΔT/Hot

Backup/Dual

Sensor with RTDs/

Thermocouples*

ΔT/Hot

Backup/Dual

Sensor with RTDs/

Thermocouples*

ΔT/

Hot Backup/Dual

Sensor with 2

RTDs with

Compensation

Loop*

“–”

“+”

Sensor Terminals (1 – 5)

Test

Ground

Quick Start Guide

April 2015

Load limitations

The power required across the transmitter power terminals is 12 to 42.4 Vdc (the

power terminals are rated to 42.4 Vdc). To prevent the possibility of damaging

the transmitter, do not allow terminal voltage to drop below 12.0 Vdc when

changing the configuration parameters.

Ground the transmitter

Ungrounded thermocouple, mV, and RTD/ohm Inputs

Each process installation has different requirements for grounding. Use the

grounding options recommended by the facility for the specific sensor type or

begin with grounding Option 1 (the most common).

Option 1 (recommended for ungrounded transmitter housing)

1. Connect signal wiring shield to the sensor wiring shield.

2. Ensure the two shields are tied together and electrically isolated from the

transmitter housing.

3. Ground shield at the power supply end only.

Ensure that the sensor shield is electrically isolated from the surrounding

grounded fixtures.

Maximum Load = 40.8 X (Supply Voltage - 12.0)(1)

1. Without transient protection (optional).

A. Remote Sensor Housing C. Sensor

B. Transmitter D. Shield Ground Points

1240

1000

750

250

12.0 Min

18.1 30 42.4

Supply Voltage (Vdc)

HART and Analog

Operating Range

4–20 mA dc

Load (Ohms)

500

1100

Analog Only

Operating Range

April 2015

Quick Start Guide

Option 2 (recommended for grounded transmitter housing)

1. Connect sensor wiring shield to the transmitter housing (only if the housing is

grounded).

2. Ensure the sensor shield is electrically isolated from surrounding fixtures that

may be grounded.

3. Ground signal wiring shield at the power supply end.

Option 3

1. Ground sensor wiring shield at the sensor, if possible.

2. Ensure the sensor wiring and signal wiring shields are electrically isolated from

the transmitter housing and other fixtures that may be grounded.

3. Ground signal wiring shield at the power supply end.

Grounded thermocouple inputs

1. Ground sensor wiring shield at the sensor.

2. Ensure the sensor wiring and signal wiring shields are electrically isolated from

the transmitter housing and other fixtures that may be grounded.

3. Ground signal wiring shield at the power supply end.

A. Remote Sensor Housing C. Sensor

B. Transmitter D. Shield Ground Points

A. Transmitter C. Sensor

B. Shield Ground Points

Andere Handbücher für Rosemount 3144P

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 3095FB MultiVariable MODBUS Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount 1066 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Fisher 4200 Bedienungsanleitung

Emerson

Emerson Rosemount 6888A Bedienungsanleitung

Emerson

Emerson Rosemount 2051HT Bedienungsanleitung

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Rosemount 2090 Konfigurationshandbuch

Emerson

Emerson Rosemount 702DX22 Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Rosemount 8732EM Bedienungsanleitung

Emerson

Emerson Rosemount 3101 Bedienungsanleitung

Emerson

Emerson Rosemount 2051L Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount X-well 648 Bedienungsanleitung

Emerson

Emerson Micro Motion 2400S Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung