Emerson Rosemount 5300 Series Bedienungsanleitung
Quick Start Guide
00825-0100-4530, Rev HA
February 2019
Rosemount™ 5300 Level Transmitter
Guided Wave Radar
Contents
About this guide............................................ 3
Confirm system readiness (HART® only).........5
Mount transmitter on tank.............................6
Prepare the electrical connections............... 11
Connect wiring and power up...................... 19
Configure.....................................................22
Safety Instrumented Systems (4-20 mA only)..
25
Adjust probe length..................................... 26
Product certifications...................................29
Quick Start Guide February 2019
2 Rosemount 5300 Level Transmitter
1 About this guide
This Quick Start Guide provides basic guidelines for the Rosemount 5300
Level Transmitter. Refer to the Rosemount 5300 Reference Manual for more
instructions. The manual and this guide are also available electronically on
Emerson.com/Rosemount.
WARNING
Failure to follow safe installation and servicing guidelines could result in death
or serious injury.
•Make sure the transmitter is installed by qualified personnel and in
accordance with applicable code of practice.
•Use the equipment only as specified in this Quick Start Guide and the
Reference Manual. Failure to do so may impair the protection provided by
the equipment.
•Any substitution of non-recognized parts may jeopardize safety. Repair,
e.g. substitution of components etc., may also jeopardize safety and is
under no circumstances allowed.
Explosions could result in death or serious injury.
•Verify that the operating atmosphere of the transmitter is consistent with
the appropriate hazardous locations certifications.
•To prevent ignition of flammable or combustible atmospheres, disconnect
power before servicing.
•Before connecting a handheld communicator in an explosive atmosphere,
ensure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
•To avoid process leaks, only use the O-ring designed to seal with the
corresponding flange adapter.
Electrical shock could cause death or serious injury.
•Avoid contact with the leads and terminals. High voltage that may be
present on leads can cause electrical shock.
•Make sure the mains power to the transmitter is off and the lines to any
other external power source are disconnected or not powered while
wiring the transmitter.
•Ground device on non-metallic tanks (e.g. fiberglass tanks) to prevent
electrostatic charge build-up.
February 2019 Quick Start Guide
Quick Start Guide 3
WARNING
Probes with non-conducting surfaces
•Probes covered with plastic and/or with plastic discs may generate an
ignition-capable level of electrostatic charge under certain extreme
conditions. Therefore, when the probe is used in a potentially explosive
atmosphere, appropriate measures must be taken to prevent electrostatic
discharge.
Eliminate the risk of ESD discharge prior to dismounting the transmitter head
from the probe.
•Probes may generate an ignition-capable level of electrostatic charge
under extreme conditions. During any type of installation or maintenance
in a potentially explosive atmosphere, the responsible person should
make sure that any ESD risks are eliminated before attempting to separate
the probe from the transmitter head.
Quick Start Guide February 2019
4 Rosemount 5300 Level Transmitter
2 Confirm system readiness (HART® only)
2.1 Confirm HART® revision capability
If using HART based control or asset management systems, confirm the HART
capability of those systems prior to transmitter installation. Not all systems
are capable of communicating with HART Revision 7 protocol.
Transmitters with a firmware version 2F0 or later can be configured for either
HART Revision 5 or 7.
2.2 Confirm correct device driver
Procedure
•Verify that the latest Device Driver (DD/DTM™) is loaded on your systems
to ensure proper communication. See Table 2-1.
•Download the latest Device Driver from Emerson.com/DeviceInstallKits.
Table 2-1: Rosemount 5300 Device Revisions and Files
Firmware version (1) Find Device Driver
HART® Universal
Revision
Device Revision (2)
2F0 or later 7 4
5 3
2A2 - 2E0 5 3
(1) Firmware version is printed on the transmitter head label, e.g. SW 2E0 or can
be found in Rosemount Radar Master (select Device > Properties).
(2) Device revision is printed on the transmitter head label, e.g. HART Dev Rev 4.
2.3 Switch HART® revision mode
If the HART configuration tool is not capable of communicating with HART
Revision 7, the device will load a generic menu with limited capability. To
switch the HART revision mode from the generic menu:
Procedure
1. Locate the “Message” field.
2. In the Message field, enter HART5 or HART7 and then 27 trailing
spaces.
February 2019 Quick Start Guide
Quick Start Guide 5
3 Mount transmitter on tank
For flexible single lead probes ordered with weight unmounted (option code
WU), refer to Adjust probe length before mounting the transmitter.
3.1 Threaded/Flange/Tri-Clamp® tank connection
Procedure
1. Seal and protect the threads.
Only for NPT threaded tank connection.
Use anti-seize paste or PTFE tape according to your site procedures.
2. Mount the device on tank.
$&%
A. NPT
B. Flange
C. Gasket
Quick Start Guide February 2019
6 Rosemount 5300 Level Transmitter
&&$%
A. Tri-Clamp
B. BSP/G
C. Gasket
3. (Optional) Adjust display orientation.
4. Tighten the nut.
Torque 30 ft-lb (40 Nm)
February 2019 Quick Start Guide
Quick Start Guide 7
3.2 Install remote housing
Procedure
1. Carefully remove the transmitter.
2. Mount the probe on tank.
$
A. Gasket
3. Mount the remote connection on the probe.
Torque 30 ft-lb (40 Nm)
Quick Start Guide February 2019
8 Rosemount 5300 Level Transmitter
4. Mount the bracket to the pipe.
4X
$%
A. Horizontal pipe
B. Vertical pipe
5. Fasten the housing support.
3X
6. Mount the transmitter head.
Torque 30 ft-lb (40 Nm)
February 2019 Quick Start Guide
Quick Start Guide 9
3.3 Bracket mounting
Procedure
1. Mount the bracket to the pipe/wall.
On pipe:
4X
$%
A. Horizontal pipe
B. Vertical pipe
On wall:
4X
2. Mount the transmitter with probe to the bracket.
3X
Quick Start Guide February 2019
10 Rosemount 5300 Level Transmitter
Andere Handbücher für Rosemount 5300 Series
3
Inhaltsverzeichnis
Andere Emerson Sender Handbücher
Emerson
Emerson Rosemount 702 Bedienungsanleitung
Emerson
Emerson Rosemount 1199 Bedienungsanleitung
Emerson
Emerson Rosemount 848T Bedienungsanleitung
Emerson
Emerson ROSEMOUNT 5300 Bedienungsanleitung
Emerson
Emerson Rosemount 4088B MultiVariable Bedienungsanleitung
Emerson
Emerson Rosemount 5081 Bedienungsanleitung
Emerson
Emerson Micro Motion ELITE Bedienungsanleitung
Emerson
Emerson Rosemount 1408A Bedienungsanleitung
Emerson
Emerson Rosemount 248 Bedienungsanleitung
Emerson
Emerson MICRO MOTION 2700 Kurzanleitung
Emerson
Emerson Rosemount 248 Bedienungsanleitung
Emerson
Emerson Rosemount 2051CF series Bedienungsanleitung
Emerson
Emerson Rosemount 550PT Bedienungsanleitung
Emerson
Emerson Rosemount ET310C Bedienungsanleitung
Emerson
Emerson Rosemount 3051SF Series Bedienungsanleitung
Emerson
Emerson Micro Motion 2500 Kurzanleitung
Emerson
Emerson Rosemount 644 Bedienungsanleitung
Emerson
Emerson Fisher 4210 Bedienungsanleitung
Emerson
Emerson Micro Motion 5700 Bedienungsanleitung
Emerson
Emerson Rosemount 5408 Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
