Emerson Rosemount 4088B MultiVariable Bedienungsanleitung

Quick Start Guide

00825-0200-4088, Rev CB

September 2018

Rosemount™ 4088B MultiVariable™

Transmitter

with Bristol™ Standard Asynchronous/

Synchronous Protocol (BSAP)/MVS

Protocol

Safety messages

NOTICE

This guide provides basic guidelines for the Rosemount 4088 MultiVariable Transmitter. It does not

provide instructions for diagnostics, maintenance, service, or troubleshooting. Reference the 4088

MultiVariable Transmitter Reference Manual for more instruction. All documents are available

electronically at Emerson.com/Rosemount.

Procedures and instructions in this section may require special precautions to ensure the safety of the

personnel performing the operation. Information that raises potential safety issues is indicated with a

warning symbol ( ). Refer to the following safety messages before performing an operation

preceded by this symbol.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate

local, national, and international standards, codes, and practices. Review the approvals section of the

4088 MultiVariable Transmitter Reference Manual for any restrictions associated with a safe

installation.

•Before connecting a Field Communicator in an explosive atmosphere, ensure the instruments in

the loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.

•In an Explosion-proof/Flameproof installation, do not remove the transmitter covers when power

is applied to the unit.

Process leaks may cause harm or result in death.

Install and tighten process connectors before applying pressure.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

•Unless marked, the conduit/cable entries in the transmitter housing use a 1/2–14 NPT thread

form. Entries marked “M20” are M20 x 1.5 thread form. On devices with multiple conduit entries,

all entries will have the same thread form. Only use plugs, adapters, glands, or conduit with a

compatible thread form when closing these entries.

•When installing in a hazardous location, use only appropriately listed or Ex certified plugs,

adapters, or glands in cable/conduit entries.

Contents

Steps required for quick installation .............. 5

Mount the transmitter .................................. 6

Consider housing rotation .......................... 13

Set the switches ......................................... 15

Wiring and power up .................................. 16

Verify device configuration ......................... 25

Trim the transmitter ................................... 26

Product Certifications ................................. 27

Quick Start Guide September 2018

2 Rosemount 4088B MultiVariable Transmitter Quick Start Guide

September 2018 Quick Start Guide

Quick Start Guide 3

1 Steps required for quick installation

•Start >

•Mount the transmitter : Mount the Transmitter

•Consider housing rotation : Consider Housing Rotation

•Set the switches : Set the Switches

•Wiring and power up : Wiring and Power Up

•Verify device configuration : Verify Device Configuration

•Trim the transmitter : Trim the Transmitter

•> Finish

September 2018 Quick Start Guide

Quick Start Guide 5

2 Mount the transmitter

2.1 Liquid flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the drain/vent valves are oriented

upward.

A. Direction of flow

2.2 Gas flow applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

A. Direction of flow

Quick Start Guide September 2018

6 Rosemount 4088B MultiVariable Transmitter Quick Start Guide

2.3 Steam flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

A. Direction of flow

2.4 Mounting brackets

Figure 2-1: Mounting Bracket – Coplanar Flange

Panel mount Pipe mount

September 2018 Quick Start Guide

Quick Start Guide 7

Figure 2-2: Mounting Brackets – Traditional Flange

Panel mount Pipe mount

Figure 2-3: Mounting Brackets – In-line

Panel mount Pipe mount

2.5 Bolting considerations

About this task

If the transmitter installation requires assembly of a process flange, manifold,

or flange adapters, follow these assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitter. Only use bolts

supplied with the transmitter or sold by Emerson™ as spare parts. Figure 2-4

illustrates common transmitter assemblies with the bolt length required for

proper transmitter assembly.

Quick Start Guide September 2018

8 Rosemount 4088B MultiVariable Transmitter Quick Start Guide

Figure 2-4: Common Transmitter Assemblies

4 × 1.75-in.

(44 mm)

4 × 1.75-in.

(44 mm)

4 × 2.25-in.

(57 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 2.88-in.

(73 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional Rosemount Conventional

Manifold and flange adapters

Note

For all other manifolds, contact Customer Central technical support.

Bolts are typically carbon steel or stainless steel. Confirm the material by

viewing the markings on the head of the bolt and referencing Table 2-1 . If

bolt material is not shown in Table 2-1, contact the local Emerson

representative for more information.

Use the following bolt installation procedure:

Procedure

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 2-1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing

pattern. See Table 2-1 for final torque value.

September 2018 Quick Start Guide

Quick Start Guide 9

5. Verify the flange bolts are protruding through the sensor module

before applying pressure (see Figure 2-5).

Example

Table 2-1: Torque Values for the Flange and Flange Adapter Bolts

Bolt material Head markings Initial torque Final torque

Carbon Steel

(CS)

B7M

300 in-lb 650 in-lb

Stainless Steel

(SST)

316

STM

316

B8M

150 in-lb 300 in-lb

Figure 2-5: Proper Bolt Installation

A. Bolt

B. Sensor module

Quick Start Guide September 2018

10 Rosemount 4088B MultiVariable Transmitter Quick Start Guide

2.6 O-rings with flange adapters

WARNING

Failure to install proper flange adapter O-rings may cause process leaks, which

can result in death or serious injury. Only use the O-ring that is designed for its

specific flange adapter.

A. Flange adapter

B. O-ring

C. PTFE-based profile (square)

D. Elastomer profile (round)

Whenever the flange or adapters are removed, visually inspect the O-rings.

Replace them if there are any signs of damage, such as nicks or cuts. If the O-

rings are replaced, re-torque the flange bolts and alignment screws after

installation to compensate for seating of the O-rings.

2.7 Environmental seal for housing

Thread sealing (PTFE) tape or paste on male threads of conduit is required to

provide a water/dust tight conduit seal and meets requirements of NEMA®

Type 4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are

required. For M20 threads, install conduit plugs to full thread engagement or

until mechanical resistance is met.

2.8 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located under the sensor module neck label. (See Figure 2-6)

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so that any contaminants

can drain away.

September 2018 Quick Start Guide

Quick Start Guide 11

Andere Handbücher für Rosemount 4088B MultiVariable

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Wireless Series Bedienungsanleitung

Emerson

Emerson Rosemount 1066 Bedienungsanleitung

Emerson

Emerson Micro Motion 3500 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 3095FB MultiVariable MODBUS Bedienungsanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 6888A Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 702DX22 Bedienungsanleitung

Emerson

Emerson Rosemount 3051N Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson Rosemount 5081 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 3051HT Bedienungsanleitung

Emerson

Emerson MICRO MOTION 2700 Bedienungsanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Emerson

Emerson Rosemount 2240S Bedienungsanleitung

Emerson

Emerson CSI 9420 Bedienungsanleitung

Emerson

Emerson Rosemount 1199 Bedienungsanleitung

Emerson

Emerson Net Safety Millennium II Bedienungsanleitung

Emerson

Emerson Micro Motion 1000 Series Kurzanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung