Endon EL-40053 Bedienungsanleitung
The Light pack contains:
Wall light and bracket.
Terminal connection block.
LED GU10 lamp
The following tools may be required:
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.
INSTRUCTION MANUAL
This product is only suitable for connection to a 240V~50Hz supply.
It is recommended that this light is installed by a qualified electrician in accordance with current IEE Wiring
Regulations and Building Regulations (Part P).
The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature
circuit breaker).
This light has an IP44 (splash proof) rating suitable for use outdoors.
Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm2
(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it
must come out of the flat surface of the mounting surface in line with the entry to the fitting.
Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,
a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a
protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable
covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,
conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable
disturbance of the ground.
This product contains breakable parts – be careful during handling and maintenance to avoid breakage.
The shade can become hot in use. Switch off and allow 10 minutes to cool before cleaning (using a dry cloth
only – do not use liquid or abrasive cleaners).
If the cover is broken or cracked then it must be replaced immediately to preserve the water ingress
protection, please consult your retailer. This is represented by the symbol
This is fitted with an LED lamp and we recommend that you do not stare into the light beam of LED`s.
If any modification is made it will invalidate the warranty and may render the product unsafe.
Before you start
Please read these instructions carefully before fitting your new light and retain for reference.
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker
before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
EL- 40053 Outdoor wall fitting.
Safety Warnings
Endon
LS9 0SE
20150324
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.
Assembly / user instructions
P570 07
Diagram A
Diagram B
Diagram C
1. Diagram A. Determine the position of your light fitting
taking into account the exit position of the cable.
Ensure that the mounting surface is solid, preferably a
brick or block wall and ensure that there are no other
cables or pipes beneath the surface. Use appropriate
fixings. Wall plugs and screws as supplied are shown
here.
2. Separate the plastic back plate from the fitting by
removing the two domed nuts on the front of the fitting.
Leave the threaded (1) bolts in the back plate. Use the
back plate as a template to mark the screw holes.
Make sure the back plate is correctly aligned.
3. Diagram B. Use a sharp object such as a screwdriver
to pierce the rubber grommet in the back plate. Feed
the incoming cable (2) through the rubber grommet and
attach the back plate to the wall. Do not over tighten as
this could damage the back plate.
4. Diagram C. Connect the house wiring to the internal
terminal block. The terminal block can be removed
from its mount for ease of connection. NOTE: This is a
Class II fitting and must not be earthed. If you have
any earth cables make sure that they are connected to
each other – to maintain earth continuity throughout
your property – and wrap them in insulation tape and
keep them away from the terminal connections of the
fitting.
5. Diagram D. Place the fitting over the back plate,
ensuring that the bolts in the back plate are aligned
with the holes in the front of the fitting. Replace the
domed nuts (3) to secure the fitting. Do not over
tighten. Fit the LED bulb (supplied) into the lamp
holder.NOTE: Never fit bulbs of a higher wattage
or of a type other than those specified on the label
(as these may cause overheating and damage the
fitting).
6. Diagram E. Fit the bulb cover
7. Turn on the power and test.
Diagram D
Diagram E
(1)
(1)
(2)
(3)
Internal
cables
Inhaltsverzeichnis
Andere Endon Außenleuchte Handbücher
Endon
Endon Canillo Bedienungsanleitung
Endon
Endon YG-6002-SS Bedienungsanleitung
Endon
Endon EL-40085 Bedienungsanleitung
Endon
Endon YG-864-SS Bedienungsanleitung
Endon
Endon Dean 82013 Bedienungsanleitung
Endon
Endon YG- 8002 Bedienungsanleitung
Endon
Endon EL-YG-5006 Bedienungsanleitung
Endon
Endon Cambridge Wall Light Bedienungsanleitung
Endon
Endon EL-40022 Bedienungsanleitung
Endon
Endon YG-7501 Bedienungsanleitung
Endon
Endon EL- 40119 Bedienungsanleitung
Endon
Endon Joshua Bedienungsanleitung
Endon
Endon Roko Bedienungsanleitung
Endon
Endon EL-533-28W-T5 Bedienungsanleitung
Endon
Endon YG-861-SS Bedienungsanleitung
Endon
Endon YG-3004 Bedienungsanleitung
Endon
Endon YG-4002-SS Bedienungsanleitung
Endon
Endon Pagoda PIR Outdoor Wall Light Bedienungsanleitung
Endon
Endon Middleton EL-40017 Bedienungsanleitung
Endon
Endon Elan 5lt Bedienungsanleitung
Beliebte Außenleuchte Handbücher anderer Marken
LIGMAN
LIGMAN BAMBOO 3 Bedienungsanleitung
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung
urban ambiance
urban ambiance UQL1273 Bedienungsanleitung
TotalPond
TotalPond 52238 Bedienungsanleitung
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Bedienungsanleitung