Endress+Hauser Liquicap M FMI51 Bedienungsanleitung

BA298F/00/en/04.07

71039049

Valid as of software version:

FW: V 01.03.00

HW: V 02.00

Operating Instructions

Liquicap M FMI51, FMI52

FEI50H HART

Capacitive Level Measurement

Brief overview Liquicap M FMI51, FMI52

2Endress+Hauser

Brief overview

For quick and easy commissioning:

Safety instructions

Explanation of the warning symbols

You can find special instructions at the appropriate position in the chapter in

question. The positions are indicated with the icons Warning #, Caution "and

Note !.

→Page 6 ff.

Installation

Here you can find the steps for installing the device and the installation

conditions

(such as the dimensions etc.).

→Page 16 ff.

Wiring

The device is delivered ready-wired as far as is possible. →Page 34 ff.

Display and operating elements

Here you can find an overview of the layout of the device's display and

operating elements.

→Page 39 ff.

Commissioning

The "Commissioning" section tells you how to switch on the device and check

the functions.

→Page 55 ff.

Troubleshooting

If faults and malfunctions occur during operation, use the checklist to find the

cause.

Here you can find measures you can take yourself to rectify any errors that may

occur.

→Page 91 ff.

Liquicap M FMI51, FMI52 Brief overview

Endress+Hauser 3

Brief operating instructions

L00-FMI5xxxx-16-00-00-en-002

!Note!

These Operating Instructions describe how to install and commission the level transmitter. All the

functions required for normal measuring tasks have been taken into consideration.

An overview of the configuration options at the FEI50H is provided on Page 40 ff.

2 (+)

1 (–)

HART

DXR375

#% &

Copy

GH I

PQ R S

,( ) ‘

AB C

Paste

Page

DeleteBksp

Insert

JK L

TU V

_< >

DE F

HotKey

+Hot Key

MN O

WXY Z

+* /

375

FIELDCOMMUNICATOR

FMP40:LIC0001

ONLINE

1 GROUP SELECT

2 PV 8.7m

HELP SAVE

dsdmdm

dfdas.

asdasfa

asasla.

- ToF Tool -

FieldTool

Package

- FieldCare

Commubox

FXA191/195

4...20 mA

≥Ω250

FEI50H

4...20mA

+- Display

DC voltage source

PLC

1. Install probe

2. Wiring

4. Make settings

3. Switch on power supply

Brief overview Liquicap M FMI51, FMI52

4Endress+Hauser

Liquicap M FMI51, FMI52 Table of contents

Endress+Hauser 5

Table of contents

1 Safety instructions . . . . . . . . . . . . . . . . 6

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Installation, commissioning and operation . . . . . . . . 6

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4 Notes on safety conventions and icons . . . . . . . . . . . 7

2 Identification . . . . . . . . . . . . . . . . . . . . 8

2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.3 Certificates and approvals . . . . . . . . . . . . . . . . . . . 15

2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 15

3 Installation . . . . . . . . . . . . . . . . . . . . . 16

3.1 Quick installation guide . . . . . . . . . . . . . . . . . . . . . 16

3.2 Incoming acceptance, transport, storage . . . . . . . . . 16

3.3 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 17

3.4 Installation instructions . . . . . . . . . . . . . . . . . . . . . 24

3.5 Installation examples . . . . . . . . . . . . . . . . . . . . . . . 26

3.6 With separate housing . . . . . . . . . . . . . . . . . . . . . . 31

3.7 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 33

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 34

4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . . . . 34

4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 36

4.3 Recommendations for connection . . . . . . . . . . . . . 38

4.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 38

4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 38

5 Operation . . . . . . . . . . . . . . . . . . . . . . 39

5.1 Operating options . . . . . . . . . . . . . . . . . . . . . . . . . 39

5.2 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.3 Locking/unlocking configuration . . . . . . . . . . . . . . 52

5.4 Resetting to factory setting (reset) . . . . . . . . . . . . . 52

5.5 Operation via the ToF Tool - FieldTool Package . . . 53

5.6 Operation via HART handheld terminal DXR375 . . 54

6 Commissioning. . . . . . . . . . . . . . . . . . 55

6.1 Installation and function check . . . . . . . . . . . . . . . 55

6.2 Basic setup

Commissioning without the display module . . . . . . 55

6.3 "Basic setup" menu

Commissioning with the display module . . . . . . . . 60

6.4 "Safety settings" menu . . . . . . . . . . . . . . . . . . . . . . 66

6.5 "Linearization" menu . . . . . . . . . . . . . . . . . . . . . . . 70

6.6 "Output" menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

6.7 "Device properties" menu . . . . . . . . . . . . . . . . . . . 80

6.8 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

6.9 Interface measurement . . . . . . . . . . . . . . . . . . . . . 84

7 Maintenance . . . . . . . . . . . . . . . . . . . . 88

8 Accessories . . . . . . . . . . . . . . . . . . . . . 89

8.1 Protective cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

8.2 Shortening set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

8.3 Commubox FXA191/195 HART . . . . . . . . . . . . . . 89

8.4 HAW569 surge arrester . . . . . . . . . . . . . . . . . . . . . 89

8.5 Weld-in adapter for universal adapter . . . . . . . . . . . 90

8.6 Weld-in adapter for G ¾ . . . . . . . . . . . . . . . . . . . . 90

8.7 Weld-in adapter for G 1 . . . . . . . . . . . . . . . . . . . . . 90

9 Troubleshooting . . . . . . . . . . . . . . . . . 91

9.1 Error messages at electronic insert . . . . . . . . . . . . . 91

9.2 System error messages . . . . . . . . . . . . . . . . . . . . . . 91

9.3 Possible measuring errors . . . . . . . . . . . . . . . . . . . . 93

9.4 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

9.5 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

9.6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

9.7 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

9.8 Contact addresses at Endress+Hauser . . . . . . . . . . . 95

10 Technical data . . . . . . . . . . . . . . . . . . 96

11 Operating menu. . . . . . . . . . . . . . . . . 104

11.1 "Basic calibration" menu

Commissioning with display and operating module . .

104

11.2 "Safety setting" menu . . . . . . . . . . . . . . . . . . . . . . 105

11.3 "Linearization" menu . . . . . . . . . . . . . . . . . . . . . . 106

11.4 "Output" menu . . . . . . . . . . . . . . . . . . . . . . . . . . 107

11.5 "Device properties" menu . . . . . . . . . . . . . . . . . . . 108

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Safety instructions Liquicap M FMI51, FMI52

6Endress+Hauser

1 Safety instructions

1.1 Designated use

Liquicap M FMI51, FMI52 are compact, capacitance level transmitters for the continuous

measurement of liquids.

1.2 Installation, commissioning and operation

Liquicap M is designed to meet state-of-the-art safety regulations and complies with the applicable

requirements and EC Directives. If used improperly or other than intended, the device can,

however, be a source of application-related danger, e.g. product overflow as a result of incorrect

installation or configuration. For this reason, installation, electrical connection, commissioning,

operation and maintenance of the measuring system must only be carried out by trained technical

personnel authorized to perform such work by the owner-operator. The technical personnel must

have read and understood these Operating Instructions and must follow the instructions they

contain. The device may only be repaired or modified if expressly permitted in the Operating

Instructions.

1.3 Operational safety

1.3.1 Ex area

When using the measuring system in Ex-areas, the appropriate national standards and regulations

have to be observed. Separate Ex documentation, which constitutes an integral part of this

documentation, is supplied with the device. The installation procedures, connection data and safety

instructions it contains must be observed.

• Make sure that the technical staff has adequate training.

• The special measuring and safety-related requirements for the measuring points must be

observed.

Liquicap M FMI51, FMI52 Safety instructions

Endress+Hauser 7

1.4 Notes on safety conventions and icons

To highlight safety-related or alternative processes, we have designed the following safety

instructions where every instruction is indicated by a corresponding pictogram.

Safety instructions

#Warning!

Draws attention to activities or procedures that can result in serious injuries to persons, a safety risk

or the destruction of the device if not carried out properly.

"Caution!

Draws attention to activities or procedures that can result in injuries to persons or the defective

operation of the device if not carried out properly.

!Note!

Draws attention to activities or procedures that have an indirect effect on operation, or can trigger an

unforeseen device reaction if not carried out properly.

Type of protection

0Explosion-protected equipment tested for type examination

If this sign can be found on the nameplate of the device, the device can be operated in hazardous

areas or non-hazardous areas in accordance with the approval

-Ex-area

This symbol in the drawings in these Operating Instructions indicates Ex-areas. Devices located in

Ex-areas, or cables for such devices, must have appropriate explosion protection.

.Safe area (non-hazardous area)

This symbol in the drawings in these Operating Instructions indicates non-Ex areas. Devices in non-

hazardous areas must also be certified if connecting cables lead into hazardous areas.

Electrical symbols

%Direct current

A terminal to which direct voltage is applied or through which the direct current flows.

&Alternating current

A terminal to which alternating voltage (sine wave) is applied or through which the alternating

current flows.

)Ground connection

A grounded terminal which, from a user's point of view, is grounded via a grounding system.

*Protective earth connection

A terminal that has to be grounded before any other connections may be established.

+Equipotential connection

A connection that has to be connected to the grounding system of the plant. This can be a potential

matching line or a star grounding system, depending on national or company codes of practice.

Immunity to temperature change of the connecting cables

Means that the connecting cables have to withstand a temperature of 85 °C at least.

t >85°C

Identification Liquicap M FMI51, FMI52

8Endress+Hauser

2 Identification

2.1 Device designation

2.1.1 Nameplate

You can take the following technical data from the nameplate of the device:

L00-FMI5xxxx-18-00-00-en-002

Information on the nameplate of Liquicap M (example)

SIL

250002075 - -

Dat.:

IP66/ IP67

NEMA4X

MWP:

≤Ta ≤+60°C

-40°C

Liquicap M

Order Code.:

Ser.No.:

XA327F

10/04

Made in Germany, D- 79689 Maulburg

Output:

XXXXXXXXXXXXX

L1 = 1000

L3 = 500

L = 1500

FEI50H

FMI51-xxxxxxxxxxxxxx

U: 12...36 V DC

25bar

BVS 05 ATEX E 103 X

ATEX II 1/2 G EEx ia IIC T6

ATEX II 1/2 G EEx ia IIB T6

Z 65.13.xxx

4...20 mA (HART)

Functional

safety

Order number

(see ordering information)

Approval No.

ATEX

WHG approval

(German Water Resources Act)

Safety information

Max. permissible pressure

in tank

Serial number

Ambient temperature

at housing

Electronic insert

Liquicap M FMI51, FMI52 Identification

Endress+Hauser 9

2.1.2 Liquicap M FMI51

10 Approval:

A Non-hazardous area

B Non-hazardous area, WHG

C ATEX II 1/2 GD EEx ia IIC T6

D ATEX II 1/2 GD EEx ia IIC T6, WHG

E ATEX II 1/2 GD EEx ia IIB T6

F ATEX II 1/2 GD EEx ia IIB T6, WHG

G ATEX II 1/2 G EEx d (ia) IIB T6, WHG

H ATEX II 1/2 GD EEx ia IIC T6,