Endress+Hauser Liquicap M FMI51 Bedienungsanleitung

BA297F/00/en/12.05

71000300

Valid as of software version:

FW: V01.00.00

HW: V01.00

Operating Instructions

Liquicap M FMI51, FMI52

FEI57C PFM

Capacitive Level Measurement

Brief overview Liquicap M FMI51, FMI52 - Level Measurement - PFM

Brief overview

For quick and easy commissioning:

Safety instructions

Explanation of the warning symbols

You can find special instructions at the appropriate position in the chapter in

question. The positions are indicated with the icons Warning #, Caution "and

Note !.

→Page 6 ff.

Installation

Here you can find the steps for installing the device and the installation

conditions

(such as the dimensions etc.).

→Page 16 ff.

Wiring

The device is delivered ready-wired as far as is possible. →Page 33 ff.

Display and operating elements

Here you can find an overview of the layout of the device's display and

operating elements.

→Page 38 ff.

Commissioning

The "Commissioning" section tells you how to switch on the device and check

the functions.

→Page 39 ff.

Troubleshooting

If faults and malfunctions occur during operation, use the checklist to find the

cause.

Here you can find measures you can take yourself to rectify any errors that may

occur.

→Page 43 ff.

Liquicap M FMI51, FMI52 - Level Measurement - PFM Brief overview

Brief operating instructions

L00-FMI5xxxx-16-00-00-en-001

!Note!

These Operating Instructions describe how to install and commission the level transmitter.

All functions that are needed for regular measuring tasks are taken into account.

In addition, the silometer, for example, has many other functions for optimising the measuring point

and converting the measured value which do not form part of these Operating Instructions.

An overview of the configuration options at the FEI57C electronic insert is provided on

Page 38.

2 (+)

1 (–)

d2 d4

(+) (–)

Silometer

FMC672

–

mA1

–

1000

>6 m

<6 m

Probe

length

FEI57C

Yes

Build up

FEI57C

PFM

>6 m

<6 m

Yes

Build up Probe

length

FMC672

–

mA1

–

1000

4. Make settings

1. Install probe 2. Wiring

3. Switch on power supply

Brief overview Liquicap M FMI51, FMI52 - Level Measurement - PFM

Liquicap M FMI51, FMI52 - Level Measurement - PFM Table of contents

Table of contents

1 Safety instructions . . . . . . . . . . . . . . . . 6

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Installation, commissioning and operation . . . . . . . . 6

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4 Notes on safety conventions and icons . . . . . . . . . . . 7

2 Identification . . . . . . . . . . . . . . . . . . . . 8

2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.3 Certificates and approvals . . . . . . . . . . . . . . . . . . . 15

2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 15

3 Installation . . . . . . . . . . . . . . . . . . . . . 16

3.1 Quick installation guide . . . . . . . . . . . . . . . . . . . . . 16

3.2 Incoming acceptance, transport, storage . . . . . . . . . 16

3.3 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 17

3.4 Installation instructions . . . . . . . . . . . . . . . . . . . . . 24

3.5 Installation examples . . . . . . . . . . . . . . . . . . . . . . . 25

3.6 With Separate Housing . . . . . . . . . . . . . . . . . . . . . 30

3.7 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 32

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 33

4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . . . . 33

4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 35

4.3 Recommendations for connection . . . . . . . . . . . . . 37

4.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 37

4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 37

5 Operation . . . . . . . . . . . . . . . . . . . . . . 38

5.1 Quick operation guide . . . . . . . . . . . . . . . . . . . . . . 38

5.2 Display and operating elements . . . . . . . . . . . . . . . 38

5.3 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

6 Commissioning. . . . . . . . . . . . . . . . . . 39

6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

6.2 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

7 Maintenance. . . . . . . . . . . . . . . . . . . . 40

8 Accessories. . . . . . . . . . . . . . . . . . . . . 41

8.1 Protective cover . . . . . . . . . . . . . . . . . . . . . . . . . . 41

8.2 Shortening set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

8.3 HAW569 surge arrester . . . . . . . . . . . . . . . . . . . . . 41

8.4 Welding boss for universal adapter . . . . . . . . . . . . . 41

8.5 Welding neck G ¾ . . . . . . . . . . . . . . . . . . . . . . . . 42

8.6 Welding neck G 1 . . . . . . . . . . . . . . . . . . . . . . . . . 42

9 Troubleshooting . . . . . . . . . . . . . . . . . 43

9.1 Fault analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

9.2 Application errors . . . . . . . . . . . . . . . . . . . . . . . . . 43

9.3 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

9.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

9.5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

9.6 Softwarehistorie . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

9.7 Contact addresses at Endress+Hauser . . . . . . . . . . . 45

10 Technical data . . . . . . . . . . . . . . . . . . 46

Safety instructions Liquicap M FMI51, FMI52 - Level Measurement - PFM

1 Safety instructions

1.1 Designated use

Liquicap M FMI51, FMI52 are compact, capacitance level transmitters for the continuous

measurement of conductive liquids.

1.2 Installation, commissioning and operation

Liquicap M is designed to meet state-of-the-art safety regulations and complies with the applicable

requirements and EC Directives. If used improperly or other than intended, the device can,

however, be a source of application-related danger, e.g. product overflow as a result of incorrect

installation or configuration. For this reason, installation, electrical connection,

commissioning,operation and maintenance of the measuring system must only be carried out by

trained technical personnel authorised to perform such work by the owner-operator.The technical

personnel must have read and understood these Operating Instructions and must follow the

instructions they contain. The device may only be repaired or modified if expressly permitted in the

Operating Instructions.

1.3 Operational safety

1.3.1 Ex area

When using the measuring system in Ex-areas, the appropriate national standards and regulations

have to be observed. Separate Ex documentation, which constitutes an integral part of this

documentation, is supplied with the device. The installation procedures, connection data and safety

instructions it contains must be observed.

• Make sure that the technical staff has adequate training.

• The special measuring and safety-related requirements for the measuring points must be

observed.

Liquicap M FMI51, FMI52 - Level Measurement - PFM Safety instructions

1.4 Notes on safety conventions and icons

To highlight safety-related or alternative processes, we have designed the following safety

instructions where every instruction is indicated by a corresponding pictogram.

Safety instructions

Warning!

Draws attention to activities or procedures that can result in serious injuries to persons, a safety risk

or the destruction of the device if not carried out properly.

Caution!

Draws attention to activities or procedures that can result in injuries to persons or the defective

operation of the device if not carried out properly.

Note!

Draws attention to activities or procedures that have an indirect effect on operation, or can trigger an

unforeseen device reaction if not carried out properly.

Type of protection

Explosion-protected equipment tested for type examination

If this sign can be found on the nameplate of the device, the device can be operated in hazardous

areas or non-hazardous areas in accordance with the approval

Hazardous area

This symbol in the drawings in these Operating Instructions indicates Ex-areas. Devices located in

Ex-areas, or cables for such devices, must have appropriate explosion protection.

Safe area (non-hazardous area)

This symbol in the drawings in these Operating Instructions indicates non-Ex areas. Devices in non-

hazardous areas must also be certified if connecting cables lead into hazardous areas.

Electrical symbols

Direct current

A terminal to which direct voltage is applied or through which the direct current flows.

Alternating current

A terminal to which alternating voltage (sine wave) is applied or through which the alternating

current flows.

)

Ground connection

A grounded terminal which, from a user's point of view, is grounded via a grounding system.

Protective earth connection

A terminal that has to be grounded before any other connections may be established.

Equipotential connection

A connection that has to be connected to the grounding system of the plant. This can be a potential

matching line or a star grounding system, depending on national or company codes of practice.

Immunity to temperature change of the connecting cables

Means that the connecting cables have to withstand a temperature of 85 °C at least.

t >85°C

Identification Liquicap M FMI51, FMI52 - Level Measurement - PFM

2 Identification

2.1 Device designation

2.1.1 Nameplate

You can take the following technical data from the nameplate of the device:

L00-FMI5xxxx-18-00-00-en-001

Information on the nameplate of Liquicap M (example)

250002075 - -

Dat.:

IP66/ IP67

NEMA4X

MWP:

≤Ta ≤+60°C

-40°C

Liquicap M

Order Code.:

Ser.No.:

XA327F

BVS 05 ATEX E 103 X

ATEX II 1/2 G EEx ia IIB T6

ATEX II 1/2 G EEx ia IIC T6

L1 = 1000

L3 = 1000

L = 2000

07/05

Made in Germany, D- 79689 Maulburg

Output:

XXXXXXXXXXXXX

FEI57C

FMI51-xxxxxxxxxxxxxx

U: 14,8 V DC

25bar

Z 65.13.xxx

PFM

Order number

(see ordering information)

Approval No.

ATEX

Safety information

Serial number

Ambient temperature

at housing

Electronic insert

WHG approval

(German Water Resources Act)

Max. permissible pressure

in tank

Liquicap M FMI51, FMI52 - Level Measurement - PFM Identification

2.1.2 Liquicap M FMI51

10 Approval:

A Non-hazardous area

B Non-hazardous area, WHG (German Water Resources Act)

C ATEX II 1/2 GD EEx ia IIC T6

D ATEX II 1/2 GD EEx ia IIC T6, WHG (German Water Resources Act)

E ATEX II 1/2 GD EEx ia IIB T6

F ATEX II 1/2 GD EEx ia IIB T6, WHG (German Water Resources Act)

G ATEX II 1/2 G EEx d (ia) IIB T6, WHG (German Water Resources Act)

H ATEX II 1/2 GD EEx ia IIC T6,