Endress+Hauser Proline Promass series Technische Daten

Products Solutions Services

Brief Operating Instructions

Proline Promass

Part 1 of 2

Coriolis sensor

These Instructions are Brief Operating Instructions; they are

not a substitute for the Operating Instructions pertaining to

the device.

These Brief Operating Instructions contain all of the

information on the sensor. Please also follow the Brief

Operating Instructions for the transmitter during

commissioning →  3.

KA01212D/06/EN/03.17

71360078

Proline Promass

2 Endress+Hauser

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

Proline Promass Brief Operating Instructions for the device

Endress+Hauser 3

Brief Operating Instructions for the device

The device consists of a transmitter and a sensor.

The process of commissioning these two components is described in two separate manuals:

• Sensor Brief Operating Instructions

• Transmitter Brief Operating Instructions

Please refer to both Brief Operating Instructions when commissioning the device as the

contents of the manuals complement one another:

Sensor Brief Operating Instructions

The Sensor Brief Operating Instructions are aimed at specialists with responsibility for

installing the measuring device.

• Incoming acceptance and product identification

• Storage and transport

• Installation

Transmitter Brief Operating Instructions

The Transmitter Brief Operating Instructions are aimed at specialists with responsibility for

commissioning, configuring and parameterizing the measuring device (until the first

measured value).

• Product description

• Installation

• Electrical connection

• Operation options

• System integration

• Commissioning

• Diagnostic information

Additional device documentation

These Brief Operating Instructions are the Sensor Brief Operating Instructions.

The "Transmitter Brief Operating Instructions" are available via:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

Detailed information about the device can be found in the Operating Instructions and the

other documentation:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

Table of contents Proline Promass

4 Endress+Hauser

Table of contents

1 Document information ............................................................ 5

1.1 Symbols used ......................................................................... 5

2 Basic safety instructions .......................................................... 7

2.1 Requirements for the personnel ............................................................ 7

2.2 Designated use ........................................................................ 7

2.3 Workplace safety ...................................................................... 8

2.4 Operational safety ......................................................................8

2.5 Product safety ......................................................................... 8

2.6 IT security ............................................................................ 9

3 Incoming acceptance and product identification ................................... 9

3.1 Incoming acceptance .................................................................... 9

3.2 Product identification .................................................................. 10

4 Storage and transport ........................................................... 11

4.1 Storage conditions .................................................................... 11

4.2 Transporting the product ................................................................11

5 Installation ...................................................................... 13

5.1 Installation conditions .................................................................. 13

5.2 Mounting the measuring device ...........................................................29

5.3 Post-installation check ................................................................. 31

6 Disposal ......................................................................... 31

6.1 Removing the measuring device .......................................................... 31

6.2 Disposing of the measuring device ......................................................... 31

Proline Promass Document information

Endress+Hauser 5

1 Document information

1.1 Symbols used

1.1.1 Safety symbols

Symbol Meaning

DANGER

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

NOTE!

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.1.2 Symbols for certain types of information

Symbol Meaning Symbol Meaning

Permitted

Procedures, processes or actions that

are permitted.

Preferred

Procedures, processes or actions that

are preferred.

Forbidden

Procedures, processes or actions that

are forbidden.

Tip

Indicates additional information.

Reference to documentation

Reference to page

Reference to graphic

… Series of steps

Result of a step Visual inspection

1.1.3 Electrical symbols

Symbol Meaning Symbol Meaning

Direct current Alternating current

Direct current and alternating current Ground connection

A grounded terminal which, as far as

the operator is concerned, is grounded

via a grounding system.

Document information Proline Promass

6 Endress+Hauser

Symbol Meaning

Protective ground connection

A terminal which must be connected to ground prior to establishing any other connections.

Equipotential connection

A connection that has to be connected to the plant grounding system: This may be a potential

equalization line or a star grounding system depending on national or company codes of practice.

1.1.4 Communication symbols

Symbol Meaning Symbol Meaning

Wireless Local Area Network

(WLAN)

Communication via a wireless, local

network.

Bluetooth

Wireless data transmission between

devices over a short distance.

LED

Light emitting diode is off.

LED

Light emitting diode is on.

LED

Light emitting diode is flashing.

1.1.5 Tool symbols

Symbol Meaning Symbol Meaning

Torx screwdriver Flat blade screwdriver

Cross-head screwdriver Allen key

Open-ended wrench

1.1.6 Symbols in graphics

Symbol Meaning Symbol Meaning

1, 2, 3,... Item numbers

… Series of steps

A, B, C, ... Views A-A, B-B, C-C, ... Sections

Hazardous area

Safe area (non-hazardous area)

Flow direction

Proline Promass Basic safety instructions

Endress+Hauser 7

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel must fulfill the following requirements for its tasks:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task.

‣Are authorized by the plant owner/operator.

‣Are familiar with federal/national regulations.

‣Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the application).

‣Follow instructions and comply with basic conditions.

2.2 Designated use

Application and media

The measuring device described in these Instructions is intended only for flow measurement

of liquids and gases.

Depending on the version ordered, the measuring device can also measure potentially

explosive, flammable, poisonous and oxidizing media.

Measuring devices for use in hazardous areas, in hygienic applications or where there is an

increased risk due to process pressure, are labeled accordingly on the nameplate.

To ensure that the measuring device remains in proper condition for the operation time:

‣Only use the measuring device in full compliance with the data on the nameplate and the

general conditions listed in the Operating Instructions and supplementary documentation.

‣Based on the nameplate, check whether the ordered device is permitted for the intended

use in the hazardous area (e.g. explosion protection, pressure vessel safety).

‣Use the measuring device only for media to which the process-wetted materials are

sufficiently resistant.

‣If the measuring device is not operated at atmospheric temperature, compliance with the

relevant basic conditions specified in the associated device documentation is absolutely

essential: "Documentation" section..

‣Protect the measuring device permanently against corrosion from environmental

influences.

Incorrect use

Non-designated use can compromise safety. The manufacturer is not liable for damage caused

by improper or non-designated use.

LWARNING

Danger of breakage due to corrosive or abrasive fluids!

‣Verify the compatibility of the process fluid with the sensor material.

‣Ensure the resistance of all fluid-wetted materials in the process.

‣Keep within the specified pressure and temperature range.

Basic safety instructions Proline Promass

8 Endress+Hauser

NOTICE

Verification for borderline cases:

‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in

verifying the corrosion resistance of fluid-wetted materials, but does not accept any

warranty or liability as minute changes in the temperature, concentration or level of

contamination in the process can alter the corrosion resistance properties.

Residual risks

LWARNING

The electronics and the medium may cause the surfaces to heat up. This presents a burn

hazard!

‣For elevated fluid temperatures, ensure protection against contact to prevent burns.

LWARNING

Danger of housing breaking due to measuring tube breakage!

‣In the event of a measuring tube breakage for a device version without rupture disk it is

possible for the pressure loading capacity of the sensor housing to be exceeded. This can

lead to rupture or failure of the sensor housing.

2.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

For welding work on the piping:

‣Do not ground the welding unit via the measuring device.

If working on and with the device with wet hands:

‣Due to the increased risk of electric shock, gloves must be worn.

2.4 Operational safety

Risk of injury!

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the-art safety requirements, has been tested, and left the factory in a condition in which it

is safe to operate.

It meets general safety standards and legal requirements. It also complies with the EU

directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms

this by affixing the CE mark to the device.

Proline Promass Incoming acceptance and product identification

Endress+Hauser 9

2.6 IT security

We only provide a warranty if the device is installed and used as described in the Operating

Instructions. The device is equipped with security mechanisms to protect it against any

inadvertent changes to the device settings.

IT security measures in line with operators' security standards and designed to provide

additional protection for the device and device data transfer must be implemented by the

operators themselves.

3 Incoming acceptance and product identification

3.1 Incoming acceptance

A0028673

A0029314

Are the order codes on

the delivery note (1)

and the product sticker

(2) identical?

A0029315

A0028673

A0029316

Are the goods

undamaged?

Incoming acceptance and product identification Proline Promass

10 Endress+Hauser

A0028673

Order code:

Ser. no.:

Ext. ord. cd.:

Date:

A0029317

Do the nameplate data

match the ordering

information on the

delivery note?

A0028673

A0029318

Is the CD-ROM with the

Technical

Documentation

(depends on device

version) and documents

present?

• If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.

• Depending on the device version, the CD-ROM might not be part of the delivery! The

Technical Documentation is available via the Internet or via the Endress+Hauser

Operations App.

3.2 Product identification

The following options are available for identification of the measuring device:

• Nameplate specifications

• Order code with breakdown of the device features on the delivery note

• Enter serial numbers from nameplates in W@M Device Viewer

(www.endress.com/deviceviewer): All information about the measuring device is displayed.

• Enter the serial number from the nameplates into the Endress+Hauser Operations App or

scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser Operations

App: all the information for the measuring device is displayed.

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser CleanFit P CPA 472 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit P CPA472 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CA80NO Technische Daten

Endress+Hauser

Endress+Hauser COM280 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag L 400 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Solitrend MMP40 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass F 200 HART Bedienungsanleitung

Endress+Hauser

Endress+Hauser Nivector FTI26 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prosonic T FMU 130 Bedienungsanleitung

Endress+Hauser

Endress+Hauser MODBUS RS485 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline Control CDC90 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 84 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 80 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Smartec S CLD132 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR53 Handbuch

Endress+Hauser

Endress+Hauser Liquiline System CA80AM Technische Daten

Endress+Hauser

Endress+Hauser Proline Cubemass 300 Anwendungshandbuch

Endress+Hauser

Endress+Hauser Proline t-mass 65 PROFIBUS DP Bedienungsanleitung

Endress+Hauser

Endress+Hauser Dosimag Bedienungsanleitung

Endress+Hauser

Endress+Hauser SpectraSensors OXY5500 Bedienungsanleitung

Endress+Hauser

Endress+Hauser promag 31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP40 Technische Daten

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung