Endress+Hauser Dosimag Bedienungsanleitung

Products Solutions Services

Brief Operating Instructions

Dosimag

Electromagnetic flowmeter

These Instructions are Brief Operating Instructions; they are

not a substitute for the Operating Instructions pertaining to

the device.

Detailed information about the device can be found in the

Operating Instructions and the other documentation:

• On the CD-ROM supplied (is not included in the delivery for

all device versions).

• Available for all device versions via:

– Internet: www.endress.com/deviceviewer

– Smart phone/tablet: Endress+Hauser Operations App

Description of the procedure (→  9)

KA01175D/06/EN/01.14

71255175

Dosimag

2 Endress+Hauser

TAG No.: XXX000

Ser. No.: X000X000000

Order code 00X00-XXXX0XX0XXX

www.endress.com/deviceviewer Endress+Hauser Operations App

Serial number

A0023555

Dosimag Table of contents

Endress+Hauser 3

Table of contents

1 Document information ........................................................... 4

1.1 Symbols used ........................................................................ 4

2 Basic safety instructions ......................................................... 6

2.1 Requirements for the personnel ........................................................... 6

2.2 Designated use ....................................................................... 6

2.3 Workplace safety ...................................................................... 7

2.4 Operational safety ..................................................................... 7

2.5 Product safety ........................................................................ 7

2.6 IT security ........................................................................... 7

3 Incoming acceptance and product identification .................................. 8

3.1 Incoming acceptance ................................................................... 8

3.2 Product identification .................................................................. 9

4 Storage and transport ........................................................... 10

4.1 Storage conditions .................................................................... 10

4.2 Transporting the product ............................................................... 10

5 Installation ..................................................................... 13

5.1 Installation conditions ................................................................. 13

5.2 Mounting the measuring device .......................................................... 18

5.3 Post-installation check ................................................................. 19

6 Electrical connection ............................................................ 20

6.1 Connection conditions ................................................................. 20

6.2 Connecting the measuring device ......................................................... 20

6.3 Ensuring the degree of protection ........................................................ 27

6.4 Post-connection check ................................................................. 28

7 Operation options .............................................................. 28

7.1 Overview of operation options ........................................................... 28

8 System integration .............................................................. 29

9 Commissioning ................................................................. 30

9.1 Function check ...................................................................... 30

9.2 Switching on the measuring device ........................................................ 30

9.3 Configuring the measuring device ........................................................ 30

9.4 Advanced settings .................................................................... 39

9.5 Simulation ......................................................................... 41

10 Diagnostic information ......................................................... 42

Document information Dosimag

4 Endress+Hauser

1 Document information

1.1 Symbols used

1.1.1 Safety symbols

Symbol Meaning

DANGER

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

NOTE!

This symbol contains information on procedures and other facts which do not result in personal

injury.

1.1.2 Electrical symbols

Symbol Meaning

Direct current

A terminal to which DC voltage is applied or through which direct current flows.

Alternating current

A terminal to which alternating voltage is applied or through which alternating current flows.

Direct current and alternating current

• A terminal to which alternating voltage or DC voltage is applied.

• A terminal through which alternating current or direct current flows.

Ground connection

A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.

Protective ground connection

A terminal which must be connected to ground prior to establishing any other connections.

Equipotential connection

A connection that has to be connected to the plant grounding system: This may be a potential

equalization line or a star grounding system depending on national or company codes of practice.

Dosimag Document information

Endress+Hauser 5

1.1.3 Symbols for certain types of information

Symbol Meaning

Permitted

Indicates procedures, processes or actions that are permitted.

Preferred

Indicates procedures, processes or actions that are preferred.

Forbidden

Indicates procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

Reference to documentation

Refers to the corresponding device documentation.

Reference to page

Refers to the corresponding page number.

Reference to graphic

Refers to the corresponding graphic number and page number.

,…

Series of steps

Result of a sequence of actions

Visual inspection

1.1.4 Symbols in graphics

Symbol Meaning

1, 2, 3,... Item numbers

,…

Series of steps

A, B, C, ... Views

A-A, B-B, C-C, ... Sections

A0013441

Flow direction

A0011187

Hazardous area

Indicates a hazardous area.

A0011188

Safe area (non-hazardous area)

Indicates the non-hazardous area.

Basic safety instructions Dosimag

6 Endress+Hauser

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel must fulfill the following requirements for its tasks:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Before beginning work, the specialist staff must have read and understood the instructions

in the Operating Instructions and supplementary documentation as well as in the

certificates (depending on the application)

‣Following instructions and basic conditions

2.2 Designated use

Application and media

Depending on the version ordered, the measuring device can also measure potentially

explosive, flammable, poisonous and oxidizing media.

Measuring devices for use in hazardous areas, in hygienic applications or in applications

where there is an increased risk due to process pressure, are labeled accordingly on the

nameplate.

To ensure that the measuring device remains in proper condition for the operation time:

‣Only use the measuring device in full compliance with the data on the nameplate and the

general conditions listed in the Operating Instructions and supplementary documentation.

‣Based on the nameplate, check whether the ordered device is permitted for the intended

use in the hazardous area (e.g. explosion protection, pressure vessel safety).

‣Use the measuring device only for media against which the process-wetted materials are

adequately resistant.

‣If the measuring device is not operated at atmospheric temperature, compliance with the

relevant basic conditions specified in the associated device documentation is absolutely

essential: "Device documentation" section (→  9).

Incorrect use

Non-designated use can compromise safety. The manufacturer is not liable for damage caused

by improper or non-designated use.

LWARNING

Danger of breakage of the sensor due to corrosive or abrasive fluids!

‣Verify the compatibility of the process fluid with the sensor material.

‣Ensure the resistance of all fluid-wetted materials in the process.

‣Observe the specified pressure and temperature range.

Verification for borderline cases:

‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in

verifying the corrosion resistance of fluid-wetted materials, but does not accept any

warranty or liability as minute changes in the temperature, concentration or level of

contamination in the process can alter the corrosion resistance properties.

Dosimag Basic safety instructions

Endress+Hauser 7

Residual risks

The external surface temperature of the housing can increase by max. 10 K due to the power

consumption of the electronic components. Hot process fluids passing through the measuring

device will further increase the surface temperature of the housing. The surface of the sensor,

in particular, can reach temperatures which are close to the fluid temperature.

Possible burn hazard due to fluid temperatures!

‣For elevated fluid temperature, ensure protection against contact to prevent burns.

2.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

For welding work on the piping:

‣Do not ground the welding unit via the measuring device.

If working on and with the device with wet hands:

‣It is recommended to wear gloves on account of the higher risk of electric shock.

2.4 Operational safety

Risk of injury.

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the-art safety requirements, has been tested, and left the factory in a condition in which it

is safe to operate.

It meets general safety standards and legal requirements. It also complies with the EC

directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser confirms

this by affixing the CE mark to the device.

2.6 IT security

We only provide a warranty if the device is installed and used as described in the Operating

Instructions. The device is equipped with security mechanisms to protect it against any

inadvertent changes to the device settings.

IT security measures in line with operators' security standards and designed to provide

additional protection for the device and device data transfer must be implemented by the

operators themselves.

Incoming acceptance and product identification Dosimag

8 Endress+Hauser

3 Incoming acceptance and product identification

3.1 Incoming acceptance

Are the order codes on the

delivery note (1) and the

product sticker (2) identical?

Are the goods undamaged?

Do the nameplate data match

the ordering information on

the delivery note?

Is the CD-ROM with the

Technical Documentation

(depends on device version)

and documents present?

• If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.

• Depending on the device version, the CD-ROM might not be part of the delivery! In

such cases, the technical documentation is available via the Internet or via the Endress

+Hauser Operations App, see the "Device documentation" section (→  9).

Dosimag Incoming acceptance and product identification

Endress+Hauser 9

3.2 Product identification

The following options are available for identification of the measuring device:

• Nameplate specifications

• Order code with breakdown of the device features on the delivery note

• Enter serial numbers from nameplates in W@M Device Viewer

(www.endress.com/deviceviewer): All information about the measuring device is displayed.

• Enter the serial number from the nameplates into the Endress+Hauser Operations App or

scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser Operations

App: all the information for the measuring device is displayed.

Order code:

Ext. ord. cd.:

Ser. no.:

Order code:

Ext. ord. cd.:

Ser. no.:

A0021952

 1 Example of a nameplate

1 Order code

2 Serial number (Ser. no.)

3 Extended order code (Ext. ord. cd.)

4 2-D matrix code (QR code)

For detailed information on the breakdown of the specifications on the nameplate, see

the Operating Instructions for the device (→  9).

3.2.1 Device documentation

All devices are supplied with Brief Operating Instructions. These Brief Operating

Instructions are not a substitute for the Operating Instructions pertaining to the device!

Detailed information about the device can be found in the Operating Instructions and the

other documentation:

• On the CD-ROM supplied (is not included in the delivery for all device versions).

• Available for all device versions via:

– Internet: www.endress.com/deviceviewer

– Smart phone/tablet: Endress+Hauser Operations App

The information required to retrieve the documentation can be found on the nameplate of the

device (→  1,  9).

Technical documentation can also be downloaded from the Download Area of the

Endress+Hauser web site: www.endress.com→ Download. However this technical

documentation applies to a particular instrument family and is not assigned to a specific

device.

Storage and transport Dosimag

10 Endress+Hauser

W@M Device Viewer

1. Launch the W@M Device Viewer: www.endress.com/deviceviewer

2. Enter the serial number (Ser. no.) of the device: see nameplate (→  1,  9).

 All the associated documentation is displayed.

Endress+Hauser Operations App

The Endress+Hauser Operations App is available for Android (Google play) and iOS (App

Store).

Via the serial number:

1. Launch the Endress+Hauser Operations App.

2. Enter the serial number (Ser. no.) of the device: see nameplate (→  1,  9).

 All the associated documentation is displayed.

Via the 2-D matrix code (QR code):

1. Launch the Endress+Hauser Operations App.

2. Scan the 2-D matrix code (QR code) on the nameplate (→  1,  9).

 All the associated documentation is displayed.

4 Storage and transport

4.1 Storage conditions

Observe the following notes for storage:

• Store in original packaging.

• Do not remove protective covers or protective caps installed on process connections.

• Protect from direct sunlight.

• Select a storage location where moisture cannot collect in the measuring device.

• Store in a dry and dust-free place.

• Do not store outdoors.

• Storage temperature(→  13)

4.2 Transporting the product

Transport the measuring device to the measuring point in the original packaging.

Andere Handbücher für Dosimag

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser Teqwave F Bedienungsanleitung

Endress+Hauser

Endress+Hauser Memosens COS81E Bedienungsanleitung

Endress+Hauser

Endress+Hauser SpectraSensors J22 TDLAS Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prothermo NMT 539 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CUM 750 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Memobase Plus CYZ71D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Bedienungsanleitung

Endress+Hauser

Endress+Hauser UniFit CPA 441 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Memosens Wave CKI50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Thermophant T TTR31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline t-mass 65F Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass E 300 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline t-mass 65F Handbuch

Endress+Hauser

Endress+Hauser Deltatop DP71B Handbuch

Endress+Hauser

Endress+Hauser SpectraSensors SS2100i-1 Installationsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena Biometra TS1 ThermoShaker Anleitung zur Verwendung

Endress+Hauser

Endress+Hauser Liquiline System CA80CR Bedienungsanleitung

Endress+Hauser

Endress+Hauser RID14 Technische Daten

Endress+Hauser

Endress+Hauser Levelflex FMP55 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline t-mass 65 PROFIBUS DP Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant M FTL51C Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CA80NO Technische Daten

Endress+Hauser

Endress+Hauser Liquiline CA80FE Technische Daten

Endress+Hauser

Endress+Hauser HART iTEMP TMT142B Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung