Endress+Hauser Promag 400 Index C Bedienungsanleitung

Products Solutions Services

Installation Instructions

Replacing the transmitter

Promag 400 Index C

EN Installation Instructions: EA01097D →  3

DE Einbauanleitung: EA01097D →  15

EA01097D/06/A2/03.18

71388401

EA01097D

Endress+Hauser 3

Transmitter replacement

Promag 400 Index C

Table of contents

1 Overview of spare part sets ........................................................ 4

2 Designated use .................................................................... 5

3 Personnel authorized to carry out repairs ........................................... 5

4 Safety instructions ................................................................ 6

5 Symbols used ..................................................................... 7

6 Tools list .......................................................................... 7

7 Promag 400 compact version ...................................................... 8

8 Promag 400 remote version ...................................................... 12

EA01097D

4 Endress+Hauser

1 Overview of spare part sets

The Installation Instructions apply to the following spare part sets:

Order number Device component

5X4CXX-AAAA 1 × compact transmitter, aluminum coated

5X4CXX-AAAM 1 × compact transmitter, polycarbonate

5X4CXX-AAAQ 1 × compact transmitter, polycarbonate, tilted

5X4CXX-C6AA 1 × compact transmitter, aluminum coated

5X4CXX-C6AM 1 × compact transmitter, polycarbonate

5X4CXX-C6AQ 1 × compact transmitter, polycarbonate, tilted

5X4CXX-AAAN 1 × remote transmitter, polycarbonate

5X4CXX-AAAP 1 × remote transmitter, aluminum coated

5X4CXX-C6AN 1 × remote transmitter, polycarbonate

5X4CXX-C6AP 1 × remote transmitter, aluminum coated

• The order number of the spare parts set (on the product label on the package) can

differ from the production number (on the label directly on the spare part)!

• You can find the order number of the relevant spare parts set by entering the

production number of the spare part in the spare parts search tool.

• We recommend that you keep the Installation Instructions and packaging together at

all times.

EA01097D

Endress+Hauser 5

2 Designated use

The spare part set and the Installation Instruction are used to replace a faulty unit with a

functioning unit of the same type. Use genuine parts from Endress+Hauser only.

Only original spare part sets, intended by Endress+Hauser for the measuring device, must be

used.

The verification has to be done via W@M Device Viewer; this procedure is explained below.

For some devices there is an overview of spare part sets inside the device. If the spare

part set is listed there, the verification is not required.

www.endress.com/deviceviewer

4. ?

Order code Description

Ser. No.: 12345

1. www.endress.com/deviceviewer

2. Enter serial number (Ser. No.), search for product

data and click on "spare parts".

3. List of all spare parts sets for the device.

4. Determine the order number of the spare part set.

The spare part set can only be used if the order

number of the spare part set corresponds to the

order number on the spare part list.

3 Personnel authorized to carry out repairs

Authorization to carry out repairs depends on the measuring device's approval type. The table

below shows the authorized group of people in each case.

Whoever carries out the repairs has full responsibility to ensure that work is carried out

safely and to the required quality standard. He/she must also guarantee the safety of the

device following repair.

Measuring device approval Personnel authorized to perform repairs 1)

Without approval 1, 2, 3

With approval (e.g. IECEx) 1, 2, 3

For custody transfer 4

1) 1 = Qualified specialist on customer side, 2 = Service technician authorized by Endress+Hauser,

3 = Endress+Hauser (return measuring device to manufacturer)

4 = Check with local approval center if installation/modification must be performed under supervision.

EA01097D

6 Endress+Hauser

4 Safety instructions

• Check whether the spare part matches the identification label on the measuring device, as

explained on the first page.

• The spare parts set and Installation Instructions are used to replace a faulty unit with a

functioning unit of the same type.

Use genuine parts from Endress+Hauser only.

• Comply with national regulations governing mounting, electrical installation,

commissioning, maintenance and repair procedures.

• Requirements with regard to specialized technical staff for the mounting, electrical

installation, commissioning, maintenance and repair of the measuring devices:

– trained in instrument safety.

– familiar with the individual operation conditions of the devices.

– for Ex-certified measuring devices: also trained in explosion protection.

• The measuring device is energized. Danger: Risk of electric shock! Open the measuring

device in a de-energized state only.

• In the case of Ex-certified measuring devices: Only open in a de-energized state (once a

delay of 10 minutes has elapsed after switching off the power supply) or in environments

which do not have a potentially explosive atmosphere.

• In the case of measuring devices in safety-related applications in accordance with

IEC 61508 or IEC 61511: After repair recommission in accordance with Operating

Instructions. Document the repair procedure.

• Before removing the device: set the process in a safe condition and purge the pipe of

dangerous materials.

• Hot surfaces! Risk of injury! Before commencing work, allow the system and measuring

device to cool down to a touchable temperature.

• In the case of measuring devices in custody transfer, the custody transfer status no longer

applies once the lead seal has been removed.

• Follow the Operating Instructions for the device.

• Risk of damaging electronic components! Ensure you have a working environment

protected from electrostatic discharge.

• After removing the electronics cover, there is a risk of electric shock as shock protection is

removed!

Switch off the measuring device before removing internal covers.

• Modifications to the measuring device are not permitted.

• Only open housing for a brief period. Avoid the penetration of foreign bodies, moisture or

contaminants.

• Replace defective seal/gaskets with genuine parts from Endress+Hauser only.

• If threads are damaged or defective, the measuring device must be repaired.

• Threads (e.g. of the cover for the electronics and connection compartments) must be

lubricated. Use an acid-free, non-hardening grease if an abrasion resistant dry lubricant is

non-existent.

EA01097D

Endress+Hauser 7

• If spacing is reduced or the dielectric strength of the measuring device cannot be

guaranteed during repair work, perform a test on completion of the work (e.g. high-voltage

test in accordance with the manufacturer's instructions).

• Service connector:

– Do not connect in potentially explosive atmospheres.

– Only connect to Endress+Hauser service devices.

• Observe the instructions for transporting and returning the device outlined in the Operating

Instructions.

If you have any questions, contact your Endress+Hauser service organization.

5 Symbols used

5.1 Symbols for certain types of information

Symbol Meaning

Permitted

Procedures, processes or actions that are permitted.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

… Series of steps

6 Tools list

3 mm, 4 mm 0.5 × 3.5 mm T20 Wire cutter

EA01097D

8 Endress+Hauser

7 Promag 400 compact version

7.1 Backing up the data

Remove the existing T-DAT from the current electronics module and insert it into the

new electronics module. If the T-DAT is no longer available, the new T-DAT can be used

(included in the delivery). In this case, proceed as follows: read and note the parameters

on the display and save them to the new electronics module following the repair.

7.2 Removing the transmitter

1 → 2 →

T20

3 →

EA01097D

Endress+Hauser 9

4 → 5 →

3 mm

6 → 7 → 8 →

PUSH TO

REMOVE

T20

1.5 Nm

(1.1 lbf ft)

‣1. This step must only be

performed if a connection board

is present. The connection board

must be re-used.

‣2. This step must only be

performed if a connection board

is present. The connection board

must be re-used.

9 → 10 →

T20

PUSH TO

REMOVE

PUSH TO

REMOVE

EA01097D

10 Endress+Hauser

4 mm

7.3 Promag 400 compact version

7.3.1 Assembling the transmitter

Ensure that the amplifier connector (Fig. 5 below) has been plugged in correctly. If the

current transmitter has a connection board (as in Fig. 3), this board must be installed in

the new transmitter. This is because the connection board contains the S-DAT with all

the sensor-related data. In this case, the jumper must be removed as indicated (Fig. 1

below).

1 → 2 → 3 →

4 mm

5.5 Nm

(4.1 lbf ft)

‣1. This step must only be

performed if a connection board

is present.

Inhaltsverzeichnis

Sprachen:

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93 Technische Daten

Endress+Hauser

Endress+Hauser Liquiphant M/S with electronic Insert FEL56 Bedienerhandbuch

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 Bedienungsanleitung

Endress+Hauser

Endress+Hauser FTL62 Series Gebrauchsanweisung

Endress+Hauser

Endress+Hauser Proline Promag L 400 HART Bedienungsanleitung

Endress+Hauser

Endress+Hauser Stamosens CSM750 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prosonic S FMU95 PROFIBUS DP Bedienungsanleitung

Endress+Hauser

Endress+Hauser Analytik Jena multi EA 4000 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 51 Bedienungsanleitung

Endress+Hauser

Endress+Hauser PROline promag 53 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 80 Technische Daten

Endress+Hauser

Endress+Hauser Ceraphant PTP31B Bedienungsanleitung

Endress+Hauser

Endress+Hauser SpectraSensors J22 TDLAS Bedienungsanleitung

Endress+Hauser

Endress+Hauser Stamolys CA71NO Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR20 Technische Daten

Endress+Hauser

Endress+Hauser Liquicap T FMI21 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag L 400 Bedienungsanleitung

Endress+Hauser

Endress+Hauser TOC Analyzer CA79 Bedienungsanleitung

Endress+Hauser

Endress+Hauser RIA46 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Technische Daten

Endress+Hauser

Endress+Hauser Flowfit CYA27 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquitrend QMW43 Bedienungsanleitung

Endress+Hauser

Endress+Hauser COM280 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung

Uniks

Uniks C126 Bedienungsanleitung