Endress+Hauser Prosonic flow 92 Handbuch

Technical Information

TI 060D/06/en

50102085

Portable Ultrasonic Flow Measuring

System

prosonic flow 92

Temporary volume flow measurement of liquids

with “Clamp On” sensors

Features and benefits

• Portable transmitter, battery operated,

for temporary measurements

• Built-in data logger with a capacity of

40000 measuring values

• Site Setup operating menus for

straightforward commissioning of up to

20 measurement sites

• “Clamp On” sensors, non-contact

measurement technique

• The sensors are affixed to the piping

from the outside

• Very wide range of nominal diameters

Sensors U DN 15...100

Sensors W DN 50...4000

• Wide temperature range of

–20…+80 °C

• Measuring transmitter in protected

handheld housing in: IP 50

• Sensors U in: IP 52

Sensors W in:

– IP 67 Sensorbody

– IP 52 BNC adapter

• Interfaces

– Data readout software for use with a

personal computer

– Current in- and outputs (4...20 mA)

Application

Ideally suited for temporary, bidirectional

measurement of pure or slightly soiled

liquids with a gas content of < 1% or a

solids content of < 5%.

• Application examples:

– Water, wastewater etc.

– Ultrapure water with low conductivity

– Process facilities

• The “Clamp On” sensors are equally

suitable for homogeneous piping as for

piping made of composite materials:

– steel, plastic, GRP and glass pipes

– Lined pipes

Prosonic Flow 92

2Endress+Hauser

Function and system design

Measuring principle Prosonic Flow operates on the principle of transit time difference.

An acoustic (ultrasonic) signal is transmitted in both directions from one measuring sensor to the

other. As the signal propagation velocity of the waves is less when the waves travel against the

direction of flow than along the direction of flow, a transit time difference occurs. This difference

is directly proportional to the flow velocity.

Prosonic Flow calculates the flow from the pipe cross-sectional area and the measured transit

time difference.

v ~ ∆t

Q = v · A

v = flow velocity

∆t = transit time difference

v = volume flow

A = pipe cross-sectional area

In addition to the volume flow, the system measures the sound velocity in the liquid. The sound

velocity can be used to distinguish different liquids or as a measure of product quality. You can

carry out application-specific calibrations of Prosonic Flow in the field using the Site Setup.

Signal propagation time

For accurate measurement, the ultrasonic signal needs a certain minimum signal propagation

time [t].

The measuring accuracy increases with the length of the signal propagation time (t) in a liquid.

F06-92xxxxxx-15-xx-06-xx-000

tt/2 t/2

F06-9xxxxxxx-15-05-xx-xx-000

Prosonic Flow 92

Endress+Hauser 3

Sensor arrangement Prosonic Flow W/U

The Prosonic Flow W sensors offer a choice between 1, 2 and 4 traverses and the Prosonic Flow

U sensors 2 traverses. Please note that the more reflection points there are in the pipe, the more

the signal strength decreases. (Example: 2 traverses = 1 reflection point, etc.)

Prosonic Flow W: 1 = 1 traverse, 2 = 2 traverses, 4 = 4 traverses

Prosonic Flow U: 2 = 2 traverses

Therefore, to maintain good signal quality, you should choose as few traverses as necessary to

achieve a sufficient transit time difference.

Recommendations:

To obtain optimum signal strength and the highest level of accuracy, we recommend the following:

•DN 15...50 →2 traverses

•DN 50...60 →2/4 traverses

•DN 80...600 →2 traverses

•DN 650...4000 →1 traverse

Sensor selection

Prosonic Flow U sensor type: DN 15...100

Prosonic Flow W sensor types (two versions): DN 50...300 and DN 100...4000.

•Both sensor types can be used in the DN 100...300 range.

•The W sensor type DN 50...300 should be used for a wall thickness < 4 mm and sensor type

DN 100...4000 for a wall thickness > 4 mm.

Commissioning accessories

During mounting and commissioning, in order to determine the sensor distance, you require data

on the measurement liquid, the pipe material used and the exact pipe dimensions. Data on the

most common liquids, pipe materials and lining materials are programmed into the

Prosonic Flow 92 program.

For liquids:

WATER –SEA WATER –DISTILLED WATER –AMMONIA –ALCOHOL –BENZENE –BROMIDE –

ETHANOL –GLYCOL –KEROSENE –MILK –METHANOL –TOLUOL –LUBRICATING OIL –FUEL

OIL –PETROL

For pipe materials:

CARBON STEEL –STAINLESS STEEL –CAST IRON –COPPER –PVC –ALUMINIUM –DUCTILE

IRON –ASBESTOS CEMENT –GRP –PEEK –PVDF –ACRYLIC GLASS

Liner material:

TAR EPOXY –MORTAR –RUBBER –TEFLON –GLASS PYREX –PVC

If your pipe material or liquid is not included in the pre-programmed selection of the transmitter

establish the missing data from the technical literature.

F06-9xxxxxxx-15-05-xx-xx-002

Prosonic Flow 92

4Endress+Hauser

Measuring system The measuring system consists of the following transmitter and flow measuring sensors.

Overview of components:

1 = Prosonic Flow 92 transmitter; 2 = Prosonic Flow W sensors, sensor holders and spacing ruler;

3 = Prosonic Flow U sensor assembly; 4 = Sensor connecting cables; 5 = Power adapter;

6 = Tensioning bands; 7 = Coupling medium; 8 = Carrying case

Measuring transmitter

Prosonic Flow 92 •For operation in the non hazardous area.

•Battery operation (power adapter included)

•Graphic display

•Configuration with push buttons

•Site Setup

•Data logger

•Volume and sound velocity measurement

•Single channel measurement

•Degree of protection IP 50

•Operation with Prosonic Flow W/U/P sensors

Flow measuring sensors

Prosonic Flow W •Clamp On flow measuring sensors

•Sensor pair for flow measurement and sound velocity in the

liquid during operation.

•2 sensor types for DN 50...4000 (2"...160")

•Temperature range -20...+80 °C

•Stainless steel sensor holders

•Degree of protection:

–Sensorbody in IP 67

–BNC adapter in IP 52

•Adaptor plug for BNC cables

Prosonic Flow U •Clamp On flow measuring sensors for small pipe diameters.

•Sensor pair for flow measurement and sound velocity in the

liquid during operation.

•1 sensor type for DN 15...100 (0.6"...4")

•Temperature range -20...+80 °C

•Plastic/Aluminum sensor assembly

•Degree of protection IP 52

F06-92xxxxxx-10-xx-xx-xx-000

Prosonic Flow 92

Endress+Hauser 5

Input

Measured variable Flow velocity (differential delay proportional to flow velocity)

Measuring range Prosonic Flow W/U sensors typically v = 0...7 m/s at the specified measuring accuracy

Operable flow range over 70 : 1

Input signal Current input: 4...20 mA, galvanically not isolated, for input of externally measured variable

(Display and data logging)

Output

Output signal Current output: active 4...20 mA, RL= 0...1 kΩ, galvanically isolated (from ground and analog

input)

Signal on alarm Current output → failsafe mode selectable

Load see “Output signal”

Low flow cutoff Switch points for low flow cutoff are selectable

Galvanic isolation All circuits for outputs and power supply are galvanically isolated from each other.

Power supply

Electrical connection

measuring unit

Power supply by built-in battery

To charge the battery, turn off the instrument power and connect the AC power adapter to the

device as shown below. The “FAST CHARGE”LED is lighted in red, and the “DC IN”LED is lighted

in green. When the instrument is fully charged, the “FAST CHARGE”LED flashes in red. With a

fully charged battery pack, the instrument can measure for about 5 hours (with the backlight

turned off). The time required for charging is approximately 3 hours.

F06-92xxxxxx-19-06-xx-xx-000

Prosonic Flow 92

6Endress+Hauser

Power supply by power adapter

A = View A

–1 = 17.5 V DC connector

–2 = AC power adapter for power supply and recharging the battery:

100...240 V AC, 47...63 Hz, Power consumption ≤12 W

Don’t use other power adapters, or it may result in an accident or in damage of the device.

The following mains connector adapters are delivered with the power supply:

1 = European standard

2 = GB standard

3 = USA/Japan standard

4 = Australien standard

F06-92xxxxxx-04-06-xx-xx-000

F06-92xxxxxx-04-xx-xx-xx-000

Prosonic Flow 92

Endress+Hauser 7

Electrical connection:

sensor cable connection

A = View A

–1 = Upstream sensor cable

–2 = Downstream sensor cable

Electrical connection:

analog input/output

connection

A = View A

–1 = Analog input/output connector

–2 = Analog output wires; 2.1 = red (+); 2.2 = black (-)

–3 = Analog input wires; 3.1 = red (+); 3.2 = black (-)

Potential equalisation Special measures for potential equalisation are not necessary.

F06-92xxxxxx-04-06-06-xx-001

Prosonic Flow 92

8Endress+Hauser

Cable connection Power supply connection of standard power supply (1)

Signal cable connection (input/output), circular connector, 4 pin (2)

Sensor cable connection (up stream/down stream), BNC connector (3)

Cable connections at the transmitter

Serial communication connection for data logging:

•D-SUB, 9 pin

D-SUB, 9 pin, socket

Pin Item Color

Analog input +

Analog output -

Analog input -

Analog output +

black

red

white

blue

Pin No. Symbol Item

–

R x D

T x D

D T R

G N D

D S R

R T S

C T S

–

Recive data

Send data

Data terminal ready

Signal ground

Data set ready

Send request

Send ready

–

F06-92xxxxxx-04-11-xx-xx-000

F06-92xxxxxx-04-11-xx-xx-001

Prosonic Flow 92

Endress+Hauser 9

Cable specifications Sensor cable:

•Special type coaxial cable.

•Use the ready-to-use cables supplied by E+H.

•The cables are available in lengths of 5 m and 10 m.

Mains connector adapters:

•Country specific mains connector adapters for mains supply connection.

Operation in zones of severe electrical interference:

The measuring device complies with the general safety requirements in accordance with

EN 61010, the EMC requirements of EN 61326.

Supply voltage Transmitter:

•Built-in battery

Special type Ni-Cd battery

Continuous operation time up to 5 hours (backlight OFF)

Recharching time 3 hours (power adaptor used)

•Special type power adaptor

100...240 V AC, 47...63 Hz

Flow measuring sensors:

•powered by the transmitter

Power consumption DC: < 12 W (incl. sensor)

Power supply failure Memory backup with lithium battery (lifetime approx. 5 years)

Performance characteristics

Reference operating

conditions

•Liquid temperature: +28 °C ± 2 K

•Ambient temperature: +22 °C ± 2 K

•Warm-up period: 30 minutes

Installation:

•Inlet run > 10 x DN

•Outlet run > 5 x DN

•Sensors grounded.

•The measuring sensors are correctly installed.

Maximum measured error For flow velocities between 0.5 m/s and 7 m/s and a Reynolds number of > 10000, the system

accuracy is:

± 0.5 % o.r. (of current reading)

The system is dry calibrated. The calibration factor by dry calibration is calculated based on the

actual pipe and liquid properties. This dry calibration procedure results in an additional uncer-

tainty for the measurement. The resulting accuracy of the measurement therefore is better than

2 % typically.

The zero point instability is < 10 mm/s.

Repeatability ± 0.3 % for flow velocities > 0.5 m/s

Prosonic Flow 92

10 Endress+Hauser

Operating conditions

Installation conditions

Installation instructions Mounting location

Correct measuring is possible only if the pipe is full. Avoid the following locations:

•Highest point of a pipeline. Risk of air accumulating.

•Directly upstream of a free pipe outlet in a vertical pipe.

Vertical pipes

Notwithstanding the above, the installation proposal below permits installation in an open vertical

pipe. Pipe restrictors or the use of an orifice with a smaller cross-section than the nominal diam-

eter prevent the pipe from running empty while measurement is in progress.

Installation in a vertical pipe

1 = Supply tank, 2 = Flow measuring sensors, 3 = Orifice plate, pipe restriction, 4 = Valve, 5 = Filling tank

F06-9xxxxxxx-11-05-00-xx-006

F06-9xxxxxxx-11-00-00-xx-007

Andere Handbücher für prosonic flow 92

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser IO-Link Ceraphant PTC31B Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Bedienungsanleitung

Endress+Hauser

Endress+Hauser RID14 Technische Daten

Endress+Hauser

Endress+Hauser Proline Promag 51 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP41C Bedienungsanleitung

Endress+Hauser

Endress+Hauser prowirl 70 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Gammapilot FTG20 Montageanleitung

Endress+Hauser

Endress+Hauser Teqwave T Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP40 Anwendungshandbuch

Endress+Hauser

Endress+Hauser ISEmax CAS40D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CA80HA Bedienungsanleitung

Endress+Hauser

Endress+Hauser RIA 250 Bedienungsanleitung

Endress+Hauser

Endress+Hauser eco-graph Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquicap M FMI51 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant M Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag P 200 Handbuch

Endress+Hauser

Endress+Hauser Proline Promag P 100 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prothermo NMT532 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline To Go CYM290 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proservo NMS81 Handbuch

Endress+Hauser

Endress+Hauser MODBUS RS485 Bedienungsanleitung

Endress+Hauser

Endress+Hauser promag 30 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass E 100 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Endress+Hauser prosonic flow 92 Handbuch

Beliebte Messgerät Handbücher anderer Marken