Endress+Hauser ITEMP TMT84 Bedienungsanleitung

BA00257R/09/en/02.11

71137264

Device software

01.01

Operating Instructions

iTEMP®TMT84

Temperature Head Transmitter

with PROFIBUS®PA Protocol

TMT84

2Endress+Hauser

Brief overview

For quick and straightforward commissioning:

Safety instructions Page 4

Installation instructions Page 8

Wiring Page 13

Display and operating elements Page 22

Information on configuration and operating programs from other manufac-

turers.

Information about setting the hardware write protection, device address, etc.

for PROFIBUS®PA communication

Commissioning Page 26

Commissioning using the PROFIBUS®PA interface - quick start for device

configuration for standard operation

Customer-specific configuration Page 53

Complex measurement tasks require additional functions to be configured

that the user can individually select, set and adapt to his process conditions

by setting the appropriate parameters.

A detailed description of all the functions and device parameters.

TMT84 Table of contents

Endress+Hauser 3

Table of contents

1 Safety instructions . . . . . . . . . . . . . . . . 4

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Installation, commissioning, operation . . . . . . . . . . . 4

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Notes on safety conventions and icons . . . . . . . . . . . 5

2 Identification . . . . . . . . . . . . . . . . . . . . 6

2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3 Certificates and approvals . . . . . . . . . . . . . . . . . . . . 6

2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 7

3 Installation instructions . . . . . . . . . . . . 8

3.1 Incoming acceptance, transport, storage . . . . . . . . . . 8

3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Installation instructions . . . . . . . . . . . . . . . . . . . . . . 8

3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 11

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Connecting the sensor cables . . . . . . . . . . . . . . . . . 14

4.3 PROFIBUS® PA cable specification . . . . . . . . . . . . 15

4.4 Fieldbus connection . . . . . . . . . . . . . . . . . . . . . . . 18

4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 20

5 Operation . . . . . . . . . . . . . . . . . . . . . . 21

5.1 Quick operation guide . . . . . . . . . . . . . . . . . . . . . . 21

5.2 Display and operating elements . . . . . . . . . . . . . . . 22

5.3 Operating options . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.4 Hardware settings (optional) . . . . . . . . . . . . . . . . . 24

6 Commissioning. . . . . . . . . . . . . . . . . . 26

6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6.2 Switching on the head transmitter . . . . . . . . . . . . . 26

6.3 Commissioning the PROFIBUS® PA interface . . . . 27

6.4 System integration . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.5 Cyclical data exchange . . . . . . . . . . . . . . . . . . . . . 31

6.6 Acyclical data exchange . . . . . . . . . . . . . . . . . . . . . 34

7 Maintenance. . . . . . . . . . . . . . . . . . . . 34

8 Accessories. . . . . . . . . . . . . . . . . . . . . 35

9 Troubleshooting . . . . . . . . . . . . . . . . . 35

9.1 Troubleshooting instructions . . . . . . . . . . . . . . . . . 35

9.2 Displaying the device status on the PROFIBUS® PA . .

9.3 Status messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

9.4 Application errors without messages . . . . . . . . . . . 43

9.5 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

9.6 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

9.7 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

9.8 Firmware/software history and overview of

compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

10 Technical data . . . . . . . . . . . . . . . . . . . 45

11 Operation using PROFIBUS® PA. . . . . 53

Index . . . . . . . . . . . . . . . . . . . . . . . . . .95

Safety instructions TMT84

4Endress+Hauser

1 Safety instructions

1.1 Designated use

• The device is a universal and configurable temperature head transmitter for resistance

thermometers (RTD), thermocouples (TC) and resistance and voltage transmitters. The device is

designed for installation in a terminal head form B according to DIN 43729 or field housing.

• The manufacturer cannot be held responsible for damage caused by misuse of the unit.

1.2 Installation, commissioning, operation

Please note the following:

• The device may only be installed, connected, commissioned and maintained by properly qualified

and authorized staff (e.g. electrical technicians) in strict compliance with these Operating

Instructions, applicable standards, legal regulations and certificates (depending on the

application).

• The specialist staff must have read and understood these Operating Instructions and must follow

the instructions they contain.

• The installer must ensure that the measuring system is correctly connected in accordance with

the electrical wiring diagrams.

• Damaged devices which could constitute a source of danger must not be put into operation and

must be clearly indicated as defective.

• Invariably, local regulations governing the opening and repair of electrical devices apply.

1.3 Operational safety

Please pay particular attention to the technical data on the nameplate! The nameplate is located on

the side of the transmitter housing.

Hazardous area

When using in hazardous areas, the national safety requirements must be met. Separate Ex

documentation is contained in these Operating Instructions for measurement systems that are to

mounted in hazardous areas. Strict compliance with the installation instructions, ratings and safety

instructions as listed in this supplementary documentation is mandatory. Ensure you are using the

correct Ex documentation for the relevant Ex-approved device. The number of the related Ex

documentation (XA...) is indicated on the nameplate. You can use this Ex documentation if the two

numbers (i.e. in the Ex documentation and on the nameplate) are identical.

Electromagnetic compatibility

The device meets the general safety requirements of EN 61010 and the EMC requirements of IEC/

EN 61326 as well as NAMUR recommendations NE 21 and NE 89.

#Warning!

Power must be fed to the device from an 9 to 32 VDC power supply in accordance with NEC

Class 02 (low voltage/current) with short-circuit power limit to 8 A/150 VA.

TMT84 Safety instructions

Endress+Hauser 5

1.4 Notes on safety conventions and icons

Always refer to the safety instructions in these Operating Instructions labeled with the following

symbols:

"Caution!

This symbol draws attention to activities or procedures that can lead to defective operation or to

destruction of the unit if not carried out properly.

#Warning!

This symbol draws attention to activities or procedures that can lead to injuries to persons, safety

risks or the destruction of the unit if not carried out properly.

!Note!

This symbol draws attention to activities or procedures that have an indirect effect on operation, or

can trigger an unforeseen unit reaction if not carried out properly.

ESD - Electrostatic discharge

Protect the terminals against electrostatic discharge. Failure to comply with this instruction can

result in the destruction of parts or malfunction of the electronics.

Identification TMT84

6Endress+Hauser

2 Identification

2.1 Device designation

2.1.1 Nameplate

The right device?

Compare and check the details on the device nameplate against the measuring point requirements.

a0009891

Fig. 1: Nameplate of the head transmitter (example, Ex version)

1 Power supply and extended order code

2 Serial number, device revision and firmware version

3 Approvals with symbols and 2D-barcode

4 2 lines for the TAG name

5 Approvals in hazardous area with number of the relevant Ex documentation (XA...)

6 Order code

2.2 Scope of delivery

The scope of delivery of the device comprises:

• Temperature head transmitter

• Securing material

• Multilingual hard copy of Brief Operating Instructions

• Operating Instructions and additional documentation on CD-ROM

• Additional documentation for devices that are suitable for use in hazardous areas (0 2 1),

such as Safety Instructions (XA...), Control or Installation Drawings (ZD...).

2.3 Certificates and approvals

On leaving the factory, the device was in perfect condition from the point of view of safety. The

device complies with the standards EN 61 010-1 "Protection Measures for Electrical Equipment for

Measurement, Control, Regulation and Laboratory Procedures" and with the EMC requirements of

IEC/EN 61326.

2.3.1 CE mark, declaration of conformity

The device meets the legal requirements of EU Directives. The manufacturer confirms a positive

completion of all tests by fitting the unit with a CE mark.

123

II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C

II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C

EH 08.001X

FNICO Apparatus

12345678910

Install per XA073/09/a3/01.08

9-32V

Suitable for Zone 22 when

install per XA074/09/a3/XX.XX

EH 08.002X

II3D Ex tD A22 IP54 T120°C

Made in Germany 2011

D-87484 Nesselwang

Ser.no.:

FW: X.XX.XX-[XXXXXXX

]

Input:

12345678ABCDEFGH

PROF I

BUS

PROCESS FIELDBUS

Profile: 3.02

iTEMP

TMT84-XXXXX/XX

2Dev.Rev.:

Ext. ord. cd.: XXXXX#

TMT84 Identification

Endress+Hauser 7

2.3.2 Certification PROFIBUS®PA

The temperature transmitter has successfully passed all test procedures and is certified and

registered by the PNO (PROFIBUS®user organization e.V.). The device thus meets all the

requirements of the specifications following:

• Certified according to PROFIBUS®PA Profile 3.02

• The device can also be operated with certified devices of other manufacturers (interoperability)

An overview of other approvals and certification can be found in chapter ’Technical data'.

2.4 Registered trademarks

•PROFIBUS

Registered trademark of the PROFIBUS Nutzerorganisation e.V. (Profibus User Organization),

Karlsruhe, Germany

•iTEMP

Registered trademark of Endress+Hauser Wetzer GmbH + Co. KG, Nesselwang, Germany

Installation instructions TMT84

8Endress+Hauser

3 Installation instructions

3.1 Incoming acceptance, transport, storage

3.1.1 Incoming acceptance

On receipt of the goods, check the following points:

• Are the contents or the packaging damaged?

• Is the delivery complete and is anything missing? Check the scope of delivery against you order.

3.1.2 Transport and storage

Note the following points:

• Pack the device in such a way as to protect it reliably against impact for storage (and

transportation). The original packaging provides optimum protection.

• The permitted storage temperature is -40 to +100 °C (-40 to 212 °F).

3.2 Installation conditions

3.2.1 Dimensions

The dimensions of the device can be found in chapter 10 ''Technical data''.

3.2.2 Installation point

• In the terminal head, flat face, as per DIN 43729, direct mounting on insert with cable entry

(middle hole 7 mm)

• In the field housing, separate from the process (see chapter 8 'Accessories')

!Note!

Mounting on a DIN rail as per EN 60715 is also possible with the DIN rail clip accessory,

see chapter 8 'Accessories'.

Information on installation conditions, such as ambient temperature, protection classification,

climatic class etc., can be found in chapter 10 "Technical data".

When using in the hazardous area, the limit values of the certificates and approvals must be

observed (see Safety Instructions XA or CD).

3.3 Installation instructions

A screwdriver is needed to mount the head transmitter.

"Caution!

Do not overtighten the mounting screws as this could damage the head transmitter. Maximum

torque = 1 Nm (¾ pound-feet).

TMT84 Installation instructions

Endress+Hauser 9

3.3.1 Mounting typical of Europe

a0014269-EN

Fig. 2: Head transmitter mounting (three versions)

12345

Item A Item B

Item C

Item A Mounting in a terminal head, flat face (terminal head as per DIN 43729)

1 Terminal head

2 Circlips

3Insert

4Connectionwires

5 Head transmitter

6 Mounting springs

7 Mounting screws

8 Terminal head cover

9Cableentry

Procedure:

1. Open the terminal head cover (8).

2. Guide the connection wires (4) of the insert (3) through the middle hole in the head transmitter (5).

3. Fit the mounting springs (6) onto the mounting screws (7).

4. Guide the mounting screws (7) through the lateral bores of the head transmitter and the insert (3). Then fix both

mounting screws in position with the circlips (2).

5. Then screw down the head transmitter (5) to the insert (3) in the terminal head.

6. After wiring (see chapter 4), close the terminal head cover (8) back on tight.

Item B Mounting in a field housing

1 Field housing cover

2 Mounting screws with springs

3 Head transmitter

4 Circlips

5 Field housing

Installation instructions TMT84

10 Endress+Hauser

3.3.2 Mounting typical of North America

a0008520

Fig. 3: Head transmitter mounting

1 Thermowell

2 Insert

3: Adapter, threaded joint

4: Terminal head

5: Head transmitter

6: Mounting screws

Thermometer design with thermocouples or RTD sensors and head transmitter

• Fit the thermowell (1) on the process pipe or the container wall. Secure the thermowell according

to the instructions before the process pressure is applied.

• Fit the necessary neck tube nipples and adapter (3) on the thermowell.

• Make sure sealing rings are installed if such rings are needed for harsh environmental conditions

or special regulations.

Procedure:

1. Open the cover (1) of the field housing (5).

2. Fit the mounting springs onto the mounting screws (2) and guide them through the lateral bores of the head

transmitter (3). Then fix both mounting screws in position with the circlips (4).

3. Screw the head transmitter to the field housing.

4. When wiring is complete (see chapter 4), screw the field housing cover (1) back on.

Item C Mounting on DIN rail (DIN rail as per IEC 60715)

1 Mounting screws with springs

2 Head transmitter

3 Circlips

4 DIN rail clip

5DINrail

Procedure:

1. Press the DIN rail clip (4) onto the top-hat rail (5) until it engages.

2. Fit the mounting springs onto the mounting screws (1) and guide them through the lateral bores of the head

transmitter (2). Then fix both mounting screws in position with the circlips (3).

3. Screw the head transmitter (2) to the DIN rail clip (4).

Item B Mounting in a field housing

Andere Handbücher für iTEMP TMT84

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Endress+Hauser Sender Handbücher

Endress+Hauser

Endress+Hauser Mycom S CLM 153 Bedienungsanleitung

Endress+Hauser

Endress+Hauser RMA42 Technische Daten

Endress+Hauser

Endress+Hauser iTEMP TMT31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser HART Proline 400 Technische Daten

Endress+Hauser

Endress+Hauser Liquiline CM442R Bedienungsanleitung

Endress+Hauser

Endress+Hauser OTMT85 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT111 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline M CM42 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP Montageanleitung

Endress+Hauser

Endress+Hauser Liquisys M CLM223F Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT86 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 500 PROFINET Technische Daten

Endress+Hauser

Endress+Hauser CM14 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT162 Technische Daten

Endress+Hauser

Endress+Hauser iTEMP TMT162 Handbuch

Endress+Hauser

Endress+Hauser Memograph CVM40 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT182 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquisys M CUM223 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquisys M CLM 223 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CM14 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Memograph CVM40 Technische Daten

Endress+Hauser

Endress+Hauser Cerabar M Bedienungsanleitung

Endress+Hauser

Endress+Hauser HART iTEMP TMT182B Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung

Endress+Hauser iTEMP TMT84 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken