Endress+Hauser ITEMP TMT85 Bedienungsanleitung

Products Solutions Services

BA00251R/09/EN/14.13

71209223

Device software

02.00

Operating instructions

iTEMP®TMT85

Temperature head transmitter

with FOUNDATION Fieldbus™- protocol

Endress+Hauser

Brief overview

For quick and easy commissioning:

Safety instructions →Page 4

Installation instructions →Page 8

Wiring →Page 13

Display and operating elements →Page 22

Information on configuration and operating programs from other

manufacturers.

Information about setting the hardware write protection, device

address, etc. for FOUNDATION Fieldbus communication

Commissioning →Page 27

Commissioning via the FOUNDATION Fieldbus interface - quick start

for device configuration for standard operation

Customer-specific configuration →Page 52

Complex measurement tasks require additional functions to be

configured that the user can individually select, set and adapt to his

process conditions by setting the appropriate parameters.

A detailed description of all the functions and device parameters.

TMT85

Endress+Hauser 3

Table of contents

1 Safety instructions . . . . . . . . . . . . . . . . . . 4

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Installation, commissioning, operation . . . . . . . . . 4

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Notes on safety conventions and icons . . . . . . . . . 5

2 Identification . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3 Certificates and approvals . . . . . . . . . . . . . . . . . . . . 6

2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 7

3 Installation instructions . . . . . . . . . . . . . 8

3.1 Incoming acceptance, transport, storage . . . . . . . . 8

3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Installation instructions . . . . . . . . . . . . . . . . . . . . . . 8

3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . 12

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Connecting the sensor cables . . . . . . . . . . . . . . . 14

4.3 FOUNDATION Fieldbus™ cable specification . . 15

4.4 Connecting the measuring unit . . . . . . . . . . . . . . 18

4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . 20

5 Operation. . . . . . . . . . . . . . . . . . . . . . . . . 21

5.1 Quick operation guide . . . . . . . . . . . . . . . . . . . . . 21

5.2 Display and operating elements . . . . . . . . . . . . . 22

5.3 FOUNDATION Fieldbus™ technology . . . . . . . . . 22

5.4 Configuration of the transmitter and FF functions

5.5 Hardware settings (optional) . . . . . . . . . . . . . . . . 26

6 Commissioning. . . . . . . . . . . . . . . . . . . .27

6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6.2 Switching on the measuring device . . . . . . . . . . 27

6.3 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

7 Maintenance. . . . . . . . . . . . . . . . . . . . . .33

8 Accessories . . . . . . . . . . . . . . . . . . . . . . . 33

9 Troubleshooting. . . . . . . . . . . . . . . . . . . 34

9.1 Troubleshooting instructions . . . . . . . . . . . . . . . . 34

9.2 Status messages . . . . . . . . . . . . . . . . . . . . . . . . . . 36

9.3 Application errors without messages . . . . . . . . . 40

9.4 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

9.5 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

9.6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

9.7 Software history and overview of compatibility 42

10 Technical Data . . . . . . . . . . . . . . . . . . . . 43

11 Operation via FOUNDATION Fieldbus™ .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Safety instructions TMT85

4Endress+Hauser

1 Safety instructions

1.1 Designated use

• The device is a universal and configurable temperature head transmitter for resistance

thermometers (RTD), thermocouples (TC) and resistance and voltage transmitters. The

device is designed for installation in a connection head form B according to DIN EN50446.

• The manufacturer cannot be held responsible for damage caused by misuse of the unit.

1.2 Installation, commissioning, operation

Please note the following:

• The device may only be installed, connected, commissioned and maintained by properly

qualified and authorized staff (e.g. electrical technicians) in strict compliance with these

Operating Instructions, applicable standards, legal regulations and certificates (depending

on the application).

• The specialist staff must have read and understood these Operating Instructions and must

follow the instructions they contain.

• The installer must ensure that the measuring system is correctly connected in accordance

with the electrical wiring diagrams.

• Damaged devices which could constitute a source of danger must not be put into operation

and must be clearly indicated as defective.

• Invariably, local regulations governing the opening and repair of electrical devices apply.

1.3 Operational safety

Please pay particular attention to the technical data on the nameplate! The nameplate is

located on the side of the transmitter housing.

Hazardous area

When using in hazardous areas, the national safety requirements must be met. Separate Ex

documentation is contained in these Operating Instructions for measurement systems that

are to mounted in hazardous areas. Strict compliance with the installation instructions,

ratings and safety instructions as listed in this supplementary documentation is mandatory.

The documentation number of that document (XA...) is also indicated on the nameplate.

Electromagnetic compatibility

The measuring device meets the general safety requirements of EN 61010 and the EMC

requirements of IEC/EN 61326 as well as NAMUR recommendations NE 21 and NE 89.

NOTICE

Power supply

‣Power must be fed to the device from an 9 to 32 VDC power supply in accordance with

NEC Class 02 (low voltage/current) with short-circuit power limit to 8 A/150 VA.

TMT85 Safety instructions

Endress+Hauser 5

1.4 Notes on safety conventions and icons

Always refer to the safety instructions in these Operating Instructions labeled with the

following symbols:

Symbol Meaning

A0011190-EN

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation

can result in serious or fatal injury.

A0011191-EN

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation

can result in minor or medium injury.

A0011192-EN

NOTICE!

This symbol contains information on procedures and other facts which do not

result in personal injury.

ESD - Electrostatic discharge

Protect the terminals against electrostatic discharge. Failure to comply with

this instruction can result in the destruction of parts or malffunction of the

electronics.

A0011193

Indicates additional information, Tip

Identification TMT85

6Endress+Hauser

2 Identification

2.1 Device designation

2.1.1 Nameplate

The right device?

Compare the nameplate on the device with the following graphic:

A0008278

Fig. 1: Nameplate of the head transmitter (example)

1 Device identification number (Device_ID)

2 Power supply and extended order code

3 Serial number and FW release

4 Approvals with symbols

52Dbarcode

6Tagname(TAG)

7 Approval in hazardous area with number of the relevant Ex documentation (XA...)

8Ordercode

2.2 Scope of delivery

The scope of delivery of the device comprises:

• Temperature head transmitter

•Securingmaterial

• Multi-language hard copy of Brief Operating Instructions

• Operating Instructions and additional documentation on CD-ROM

• Additional documentation for devices that are suitable for use in hazardous areas (0

2 1), such as Safety Instructions (XA...), Control or Installation Drawings (ZD...).

2.3 Certificates and approvals

The device is designed in accordance with good engineering practice to meet state-of-the-

art safety requirements, has been tested and left the factory in a condition in which it is safe

to operate. The device complies with the standards EN 61 010-1 "Protection Measures for

Electrical Equipment for Measurement, Control, Regulation and Laboratory Procedures" and

with the EMC requirements of IEC/EN 61326.

2.3.1 CE mark, declaration of conformity

The device described in these Operating Instructions is therefore in conformity with the

statutory requirements of the EU Directives. The manufacturer confirms a positive

completion of all tests by fitting the unit with a CE mark.

TMT85 Identification

Endress+Hauser 7

2.3.2 Certification Foundation Fieldbus™

The temperature transmitter has successfully passed all the tests and is certified and

registered by the Fieldbus Foundation. The device meets all the requirements of the

following specifications:

• Certified in accordance with FOUNDATION Fieldbus™ specification

• FOUNDATION Fieldbus™ H1

• Interoperability Test Kit (ITK), (device certification number available on request): the

device may also be operated using certified devices from other manufacturers

• Physical Layer Conformance Test of the Fieldbus FOUNDATION™

An overview of additional approvals and certifications can be found on →ä50.

2.4 Registered trademarks

FOUNDATION FieldbusTM

Registered trademark of the Fieldbus Foundation Austin, Texas, USA

Installation instructions TMT85

8Endress+Hauser

3 Installation instructions

3.1 Incoming acceptance, transport, storage

3.1.1 Incoming acceptance

On receipt of the goods, check the following points:

• Are the contents or the packaging damaged?

• Is the delivery complete and is anything missing? Check the scope of delivery against you

order.

3.1.2 Transport and storage

Note the following points:

• Pack the device in such a way as to protect it reliably against impact for storage (and

transportation). The original packaging provides optimum protection.

• The permitted storage temperature is -40 to +100 °C (-40 to 212 °F).

3.2 Installation conditions

3.2.1 Dimensions

The dimensions of the device can be found in chapter 10 ''Technical data''.

3.2.2 Installation point

• In the terminal head, flat face, as per DIN EN50446, direct mounting on insert with cable

entry (middle hole 7 mm)

• In the field housing, separate from the process (see Section 8 'Accessories')

• Mounting on a DIN rail as per EN 60715 is also possible with the DIN rail clip accessory,

see Section 8 'Accessories'.

Information on installation conditions, such as ambient temperature, protection

classification, climatic class etc., can be found in chapter 10 "Technical data".

When using in the hazardous area, the limit values of the certificates and approvals must be

observed (see Safety Instructions XA or CD).

3.3 Installation instructions

A screwdriver is needed to mount the head transmitter.

NOTICE

Damage of the head transmitter

‣Do not overtighten the mounting screws as this could damage the head transmitter.

Maximum torque = 1 Nm (¾ pound-feet).

TMT85 Installation instructions

Endress+Hauser 9

3.3.1 Mounting typical of Europe

A0008281-EN

Fig. 2: Head transmitter mounting (three versions)

Item A Mounting in a terminal head (terminal head as per DIN EN50446, flat face)

1Terminalhead

2 Circlips

3Insert

4 Connection wires

5 Head transmitter

6 Mounting springs

7Mountingscrews

8 Terminal head cover

9Cableentry

Procedure:

1. Open the terminal head cover (8).

2. Guide the connection wires (4) of the insert (3) through the middle hole in the head transmitter (5).

3. Fit the mounting springs (6) onto the mounting screws (7).

4. Guide the mounting screws (7) through the lateral bores of the head transmitter and the insert (3). Then fix

both mounting screws in position with the circlips (2).

5. Then screw down the head transmitter (5) to the insert (3) in the terminal head.

6. After wiring (see section 4), close the terminal head cover (8) back on tight.

Installation instructions TMT85

10 Endress+Hauser

3.3.2 Mounting typical of North America

A0008520

Fig. 3: Head transmitter mounting

1: Thermowell

2: Insert

3: Adapter, threaded joint

4: Terminal head

5: Head transmitter

6: Mounting screws

Item B Mounting in a field housing

1 Field housing cover

2 Mounting screws with springs

3 Head transmitter

4 Field housing

Procedure:

1. Open the cover (1) of the field housing (4).

2. Guide the mounting screws (2) through the lateral bores of the head transmitter (3).

3. Screw the head transmitter to the field housing.

4. When wiring is complete (see section 4), screw the field housing cover (1) back on.

Item C Mounting on DIN rail as per IEC 60715

1 Mounting screws with springs

2 Head transmitter

3 Circlips

4DINrailclip

5DINrail

Procedure:

1. Press the DIN rail clip (4) onto the DIN rail (5) until it engages.

2. Fit the mounting springs onto the mounting screws (1) and guide them through the lateral bores of the head

transmitter (2). Then fix both mounting screws in position with the circlips (3).

3. Screw the head transmitter (2) to the DIN rail clip (4).

1234 5

Andere Handbücher für iTEMP TMT85

Inhaltsverzeichnis

Andere Endress+Hauser Sender Handbücher

Endress+Hauser

Endress+Hauser Liquisys M COM 223 Bedienungsanleitung

Endress+Hauser

Endress+Hauser cerabar S Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prosonic S FMU95 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Flowmeter Proline 300 Technische Daten

Endress+Hauser

Endress+Hauser Deltabar S FMD76 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP41C Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT162 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP PA TMT184 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 300 Technische Daten

Endress+Hauser

Endress+Hauser iTEMP TMT82 Technische Daten

Endress+Hauser

Endress+Hauser iTEMP TMT84 Technische Daten

Endress+Hauser

Endress+Hauser Cerabar S PMP71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT85 Technische Daten

Endress+Hauser

Endress+Hauser HMX50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser FHX50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CM14 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquisys M CLM223F Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 500 digital HART Technische Daten

Endress+Hauser

Endress+Hauser iTEMP TMT125 Technische Daten

Endress+Hauser

Endress+Hauser iTEMP Montageanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT162 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT86 Technische Daten

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung

Endress+Hauser iTEMP TMT85 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken