Eneo PLD-2036PTZ Bedienungsanleitung

Quick Installation Guide

1/4

Network High Speed Dome, PTZ, 36x, Day&Night

PLD-2036PTZ

Safety Instructions _______________________________________________

• Read these safety instructions and the operation manual first before you install and commission

the camera.

• Keep the manual in a safe place for later reference.

• Protect your camera from contamination with water and humidity to prevent it from permanent

damage. Never switch the camera on when it gets wet. Have it checked at an authorized service

center in this case.

• Never operate the camera outside of the specifications as this may prevent the camera

functioning.

• Do not operate the cameras beyond their specified temperature, humidity or power ratings.

• Operate the camera only at a temperature range of -40°C to +50°C and at a humidity of max. 90%.

• To disconnect the power cord of the unit, pull it out by the plug. Never pull the cord itself.

• Pay attention when laying the connection cable and observe that the cable is not subject to heavy

loads, kinks, or damage and no moisture can get in.

• Do not attempt to disassemble the camera board from the dome.

• The warranty becomes void if repairs are undertaken by unauthorized persons.

Do not open the camera housing.

• Never point the camera towards the sun with the aperture open. This can destroy the sensor.

• Installation, maintenance and repair have to be carried out only by authorized service centers.

Before opening the cover disconnect the unit from mains input.

• Contact your local dealer in case of malfunction.

• Only use original parts and original accessories from Videor E. Hartig GmbH.

• Do not use strong or abrasive detergents when cleaning the dome.

Use a dry cloth to clean the dome surface.In case the dirt is hard to remove, use a mild detergent

and wipe gently.

• All openings provided in the housing for assembly purposes must be closed and/or sealed.

• The installer is responsible for ensuring that the degree of protection as per the technical

specifications is upheld, e.g. by using all enclosed gasket seals and O-rings, by

waterproofing the cable exits with silicon or through laying the cable in such a way that the

cable does not act as a „gutter”.

• During assembly, care must be taken to ensure that existing seals are correctly inserted

and are not displaced as a result of assembly.

You must not continue to use damaged seals.

NOTE:

This is a class A digital device. This digital device can cause harmful interference in a

residential area; in this case the user may be required to take appropriate corrective action at

his/her own expense.

This Quick Guide is for quick installing and connecting the network Speed Dome Camera.

For details, please refer to the camera’s User Manual and Installation Guide.

Switch Definition _____

Outdoor

A None

B Communication Switch (Reserved)

C RJ45 Connector

D 22-Pin Connector

E None

F F-1 Reboot Button

F-2 Factory Reset Button

G ISP Connector (for FW upgrade)

Data Cable and Connector Definition _____

Please refer to the illustrations below for connector definition of each kind of Data Cable before

wiring.

Outdoor Dome Camera:

AC 24V Data Cable

22-Pin Connector Definition _____

When cabling, please refer to the table below for pin definition of the Data Cable’s 22-pin connector

on the Data Cable.

Pin Definition Cable Pin Definition Cable

1AC 24-1/DC (＋) 20AWG/18AWG 12 ALM-1

2ALM NC 13 ALM-3

3AC 24-2/DC (－) 20AWG/18AWG 14 ALM-2

4ALM NO 15 ALM-4

5FG 20AWG18AWG

16 Reserved

6 ALM COM 17 Reserved

7 Audio in

24AWG

18 Reserved

8 Audio out 19 Reserved

9 Audio GND 20 ALM GND

10 Audio GND 21 VGND 20AWG

11 ISOG

22 Video

Before Login to the Camera _____

A client program will be automatically installed on your PC when connecting to the network Speed

Dome Camera. Before logging in to the Dome Camera, please ensure downloading the ActiveX

control is allowed by either changing the ActiveX controls and plug-ins or setting Internet’s security

level to default. For further details, please refer to the network Speed Dome Camera’s Software

Guide.

ActiveX Controls and Plug-ins Settings Internet Security Level

Step 1: Start the Internet Explorer (IE).

Step 2: Select <Tools> from the main menu of

the browser. Then Click on <Internet

Options>.

Step 3: Click on the <Security> tab and select

“Internet”, and click on <Custom level>

to change ActiveX settings.

Step 4: Set “ActiveX controls and plug-ins”

items to <Prompt> or <Enable>.

Step 1:Start the IE.

Step 2:Select <Tools> from the main

menu of the browser. Then Click

on <Internet Options>.

Step 3: Click on the <Security> tab and

select “Internet.”

Step 4: Down the page, press “Default

Level” and click on <OK> to

confirm the setting. Close the

browser window, and open a new

one later for accessing the IP

Camera

Camera Login _____

The network Speed Dome Camera’s default IP address is: 192.168.1.10. Therefore, to access the

camera for the first time, set the PC’s IP address as: 192.168.1.XXX; for example:

IP Address: 192.168.1.20

Subnet Mask: 255.255.255.0

•

Key in the camera’s IP address in the URL bar of the Web browser window and hit “Enter.”

•

Enter the default user name (admin) and password (admin) in the prompt request dialogue.

Note that user name is case sensitive.

Install the ActiveX Control

•

After connecting to the network Speed Dome Camera, the request for installing the ActiveX

control will appear just below the URL bar.

•

Right Click on the information bar, and press “Install ActiveX Control…” to permit ActiveX control

installation.

•

In the pop-up security warning window, click on <Install> to start downloading DC Viewer software

on the PC.

•

Click on <Finish> after DC Viewer installation is complete.

Browser-based Viewer _____

The main page of the network Speed Dome Camera user interface is as shown below.

Technical Specifications _____

Type PLD-2036PTZ

Art. No. 200823

Resolution standard SD

System day&night

Sensor size 1/4”

Imager CCD

Sensitivity (at 50% video signal) 1Lux (colour) ; 0.01Lux (B&W)

Horizontal resolution 650 TVL

Automatic gain control (AGC) supplied

Automatic electronic shutter (ESC) 1/50 ~ 1/10,000sec.

Digital Noise Reduction (DNR) yes, 2D & 3D

Low speed shutter yes, ON/OFF switchable

White balance automatic, indoor, outdoor, ATW, manual

Backlight compensation BLC

Wide Dynamic Range (WDR) yes

IR cut filter switchable

Resolution max. 720x576

Resolution 720x576 (4:3)

Image transmission rate max. 25 images/sec.

Frame 25fps at 704x576

Privacy zones masking 16 zones masking, ON/OFF switchable

Activity detection yes

Motion detector 10 zones

Analysis functions activity detection

Text display supplied

Sharpness correction adjustment range: 0 ~ 15

Menu languages German, English, French, Italian, Russian

OSD function control resolution, modes (presets), motion detection, BLC,

DNR, WDR, bit rate, day&night, password

External connections alarm input, alarm output, audio input, audio output

Video outputs composite (CVBS), 1Vp-p (C)VBS, 75ohms, BNC

Audio support yes

Audio 1/1 Line input and output

Alarm inputs 4

Alarm output 1x Relay out (AC120VAC 30VDC)

Alarm processing SD-card recording, alarm out, FTP, E-Mail, PTZ action

Internal storage microSD card

Compression standard H.264, MJPEG

Audio standards G.711, G.726, ADPCM/AAC

Bandwidth controllable bandwidth and frame rate

Stream types H.264, MJPEG multiple

Network connection RJ-45

Network interface 10/100Base-TX, RJ45

Web browser MS Internet Explorer vers. 7.0 or higher, Safari (Java),

Mozilla Firefox (Java), Google Chrome (Java)

Network protocols TCP/IP, UDP, RTP, RTSP, HTTP, HTTPS, ICMP, FTP,

SMTP, DHCP, PPPoE, UPnP, IGMP, SNMP, IPv4, IPv6,

IEE 802.1

Lens type zoom

Lens mount -

Focal length 3.4mm – 122.4mm

Horizontal angle of view 50.4° - 1.4°

Aperture range F1.6~F4.5

Digital zoom 12x

Iris control DC

Focus control automatic and manual

MOD (Minimum object distance) 0.5m

Illumination no

Serial interfaces no

Remote configuration via web browser

Firmware update via network interface

Operation protection Password protected

Password protection yes, two levels (administrator and user)

e-PTZ support no

Speed (manual control) 1-80°/sec.

Preset speed up to 400°/sec.

Rotation range 360° (endless)

Auto flip function mechanical, digital, off

Proportional pan and tilt continually decreases pan and tilt speeds in proportion

to depth of zoom

Patterns 8 pattern

Presets 256 Presets

Home position included (with multiple park actions)

Tours up to 8 user programmable guard tours

Supply voltage 24VAC

Power over Ethernet no

Heater yes

Power consumption 65W

Mounting optional wall/flush mounting accessories

Temperature range (operation) -40°C~+50°C

Vandalism resistant yes

Housing outdoor

Housing material plastic

Colour (housing) RAL9003

Colour (bubble) clear

Protection rating IP66, IK10

Management Software Support Zelaris

SDK available

ONVIF core specifications 1.02

Certificates CE

Dimensions See drawing

Weight 2.6kg

Parts supplied remote viewer software, screw set, manual

Special features Auto calibration

Optional Accessories

The optional accessories currently available can be found on our Homepages: www.videor.com and

www. eneo-security.com

eneo

is a registered trademark of Videor E. Hartig GmbH

Exclusive distribution through specialised trade channels only.

Videor E. Hartig GmbH

Carl-Zeiss-Straße 8 · 63322 Rödermark, Germany

Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100 V 1.4

www.videor.com Technical changes reserved.

www.eneo-security.com © Copyright by Videor E. Hartig GmbH 05/2012

Andere Handbücher für PLD-2036PTZ

Inhaltsverzeichnis

Andere Eneo Sicherheitskamera Handbücher

Eneo

Eneo IPD-75M2713M5A Bedienungsanleitung

Eneo

Eneo 232574 Bedienungsanleitung

Eneo

Eneo 230799 Bedienungsanleitung

Eneo

Eneo HDC-2220M1080 Bedienungsanleitung

Eneo

Eneo VKC-13120F2810IR Bedienungsanleitung

Eneo

Eneo VKCD-1326/IR Bedienungsanleitung

Eneo

Eneo VKCD-1323/IR Montageanleitung

Eneo

Eneo VKC-1376/12-24 Bedienungsanleitung

Eneo

Eneo NXP-880F21 Bedienungsanleitung

Eneo

Eneo IEB-54F0028M0A Bedienungsanleitung

Eneo

Eneo ICB-73M2712MWA Bedienungsanleitung

Eneo

Eneo VKCD-12140F2812IR Bedienungsanleitung

Eneo

Eneo MPD-74A0003M0A Bedienungsanleitung

Eneo

Eneo IPB-62M2713MAA Bedienungsanleitung

Eneo

Eneo NXD-1602M Bedienungsanleitung

Eneo

Eneo VKC-1338A/PIR Bedienungsanleitung

Eneo

Eneo VKC-1416B-/PP Bedienungsanleitung

Eneo

Eneo IED-62F0036M0A Bedienungsanleitung

Eneo

Eneo IPD-73M2812M0A Bedienungsanleitung

Eneo

Eneo IED-54F0036MBA Bedienungsanleitung

Eneo

Eneo Fastrax IV EDC-4222 Bedienungsanleitung

Eneo

Eneo MEP-62M2812M0A Bedienungsanleitung

Eneo

Eneo HDB-2280Z10IR D Bedienungsanleitung

Eneo

Eneo VKC-1310 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung