ENFORCER E-931-S50RRQ Bedienungsanleitung

E-931-S50RRQ

50ft Reflective Photoelectric Beam Sensor

Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.

Manual

Up to 50ft (15m) sensing range

Weatherproof (IP66)

Anti-condensation housing

12~250 VAC/VDC

Form C relay: 1A@30VDC

Beam status LED

N.C. Tamper switch:

500mA@30VDC

Caution:

This sensor is not designed to prevent bodily injury or loss of life.

This sensor is not designed for use in environments where explosive gasses may be present.

Use of this sensor in certain security applications may be regulated by local laws or codes. SECO-LARM is not

responsible for compliance with such laws or codes.

ENFORCER 50ft Reflective Photoelectric Beam Sensor

2SECO-LARM U.S.A., Inc.

Specifications:

Model

E-931-S50RRQ

Type

Reflective photoelectric

beam sensor

Sensing range

50ft (15m)

Operating voltage

12~250 VAC/VDC

Current draw (max.)

12VDC

Standby: 50mA; Active: 25mA

24VAC

Standby: 30mA; Active: 18mA

Response time

10ms

Light source

IR LED

LEDs

Solid Green

Good beam signal, properly aligned

Alternating flash

Poor beam signal

Solid Red

No beam signal, triggered

Trigger output

SPDT Relay output (NO/NC/COM)

Switching capacity

0.5A@120VAC/1A@30VDC

Tamper switch

500mA@30VDC

IP Rating

IP66

Operating temperature

-13 ~140 F (-25 ~60 C)

Parts List:

1x Sensor

1x Reflector

1x Mounting bracket

1x Sensor hood

4x Cover screws

2x Mounting screws

1x Reflector mounting screw

1x Rubber ring

1x Cable connector

1x Manual

1x Removable terminal block

Overview:

Tamper switch

Vertical

adjustment screw

(without cover)

Cover

screw

Wire cable

connector

Mounting plate

Hood

Dimensions:

Beam

sensor LED

Terminal

block

Cable breakout

Captive screw

Beam sensor

413/16”

(122mm)

3/16”

(4mm)

37/32”

(82mm)

11/32”

(9mm)

21/8”

(54mm)

23/8”

(60mm)

115/16”

(49mm)

27/16”

(62mm)

Cable breakout

Polarity does not matter for the power input.

Connect the N.C. tamper terminal to the

tamper circuit of an alarm control panel.

Wiring Diagram:

12~250

VAC/VDC

(Non-Polarity)

N.C.

N.O.

COM

Tamper

N.C.

Relay

ENFORCER 50ft Reflective Photoelectric Beam Sensor

SECO-LARM U.S.A., Inc. 3

1. Mount the sensor and reflector so that they face

each other.

2. Connect power to the sensor. The LED will light as

indicated in the chart below.

3. Unscrew the 4 cover screws and remove the cover.

4. To find the correct alignment, slowly turn the lens

assembly left and right to adjust the horizontal angle.

5. Loosen the vertical adjustment screw to adjust the

vertical angle.

6. Place the hood on the sensor by sliding the hood’s

ridges into the slots on the sides of the sensor.

7. Re-attach the cover, replace the four screws, and

attach the hood to the top of the sensor.

1. Unscrew the four cover screws and remove the cover.

2. Loosen the captive screw and remove the sensor

from the mounting plate.

3. Using the included mounting screws, mount the

mounting plate to the wall.

4. Use the cable breakout and cable connector at

the bottom or rear of the sensor to run the wires.

5. Hang the sensor back on the plate and use the captive screw to secure it in place.

6. Re-attach the cover, replace the four screws, and attach the hood to the top of the sensor.

Mounting:

Alignment:

Solid green

Good beam signal,

properly aligned

Alternating flash

Poor beam signal

Solid red

No beam signal,

triggered

Lens

alignment

±90

±5

Horizontal

adjustment

Vertical

adjustment

Wiring for the Rear Cable Breakout

1. Puncture the cable breakout located at the rear of

the sensor using a screwdriver or other object.

2. Run wires through the included rubber ring.

3. Install the weatherproofing ring with the wires already

installed in the cable breakout hole.

4. Make sure the ring is secure and there is no room for

water to get into the unit.

Rubber

ring

Cable

breakout

Wiring for the Bottom Cable Breakout

1. Puncture the cable breakout located at the bottom of

the sensor using a screwdriver or other object.

2. Insert the short end side of the cable connector

into the cable breakout hole and use the nut to

secure it, tightening with a wrench as needed.

3. Run the wires through the end cap and cable connector.

4. Then screw the end cap into the external side of the cable

connector to prevent water from entering the unit.

Cable

Connector

End cap

Sensor

Nut

Rubber

neck

ENFORCER 50ft Reflective Photoelectric Beam Sensor

4SECO-LARM U.S.A., Inc.

WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal service

for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the

repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair,

or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such

equipment is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at

SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal

or property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the

SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to

change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

part, without the written permission of SECO-LARM.

M E-931-S50RRQ_1212.docx

PITSW3

SECO-LARM®U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com

Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: i[email protected]om

Troubleshooting:

Sensor does not detect the object.

Change the angle of the sensor or readjust

the sensitivity setting.

The beam sensor LED will not turn green.

Clean the sensor and reflector with a damp

(not wet) cloth.

Adjust the reflector and/or sensor for proper

alignment.

Beam sensor LED lights when object

is detected, but there is no output.

Check wiring between the sensor and local

alarm device.

Sample Applications:

Garage

Door

Gate

Vehicle

Detection

Assembly

Line

Other Sensors Available:

Dual and

Quad Beam

Curtain and

Barrier

Optional Accessory:

Reflector Hood

E-931ACC-HR

Provides extra

protection for the

reflector.

Compatible with Reflective Photoelectric Beam Sensor models

E-931-S50RRQ, E-931-S35RRQ, and E-931-S33PRQ.

Reflective

Photobeam

Inhaltsverzeichnis

Andere ENFORCER Zubehör Handbücher

ENFORCER

ENFORCER CS-PD115-PAQ Bedienungsanleitung

ENFORCER

ENFORCER E-931-S50RRLQ Bedienungsanleitung

ENFORCER

ENFORCER SLI SECO-LARM SD-9163-KSQ Bedienungsanleitung

ENFORCER

ENFORCER ECO-LARM RM-R100-TLQ Bedienungsanleitung

ENFORCER

ENFORCER EFR-E-931-S35RRQ Bedienungsanleitung

ENFORCER

ENFORCER E-931-S35RRQ Bedienungsanleitung

ENFORCER

ENFORCER Seco-Larm SLI E-936-S45RRGQ Bedienungsanleitung

ENFORCER

ENFORCER No Touch SD-927PKC-NEQ Bedienungsanleitung

ENFORCER

ENFORCER SD-9 63 Series Bedienungsanleitung

ENFORCER

ENFORCER E-9622-4B25 Bedienungsanleitung

ENFORCER

ENFORCER E-931CS22RRCQ Bedienungsanleitung

ENFORCER

ENFORCER E-931-S50RRGQ Bedienungsanleitung

ENFORCER

ENFORCER Enforcer SD-927PKC-NEQ Bedienungsanleitung

ENFORCER

ENFORCER SECO-LARM SD-9773-KNEVQ Bedienungsanleitung

ENFORCER

ENFORCER ENFORCER EVT-RBP-GNCQ* Bedienungsanleitung

ENFORCER

ENFORCER Enforcer SD-927PKC-NEQ Bedienungsanleitung

ENFORCER

ENFORCER E-936-S35RRGQ Bedienungsanleitung

ENFORCER

ENFORCER E-931-S45RRQ Bedienungsanleitung

ENFORCER

ENFORCER E-932-D33TBQ Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung