Enviro Alliance EF3 Bedienungsanleitung

PELLET STOVE

Alliance (EF3)

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE

OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY

OR EVEN DEATH.

Contact your building or fire officials about restrictions and installation

inspection requirements in your area.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

OWNER’S MANUAL



SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED

PAPER.

50-918

Table of Contents

Introduction................................................................................................................................3

Important Safety Data.......................................................................................................3

Pellet Quality.....................................................................................................................4

Warnings and Recommendations.......................................................................................4

Automatic Safety Features of Your Pellet Stove...................................................................5

Appliance Dimensions.......................................................................................................6

Rating Label Location........................................................................................................6

Operating Instructions.................................................................................................................7

How to Turn On and Operate Your Pellet Appliance (Timer Control)......................................7

Control Board Functions....................................................................................................8

Turning Pellet Stove On (Circuit Board)...............................................................................8

Slider/Damper Operation...................................................................................................9

Routine Cleaning and Maintenance:..................................................................................10

Warranty...................................................................................................................................12

Installation Data Sheet...............................................................................................................13

Please read this entire manual before installation and use of this pellet fuel burning room heater. Failure

to follow these instructions could result in property damage, bodily injury or even death.

CAUTION: DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPTHA

OR ENGINE OIL.

UNIT HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE

AWAY. CONTACT MAY CAUSE SKIN BURNS.

Contact local building officials about restrictions and installation inspection requirements in your area.

The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive

chimney pressure, it is very important to ensure that the exhaust system be sealed and airtight.

The use of grates or other methods of supporting the fuel is not permitted.

This unit is designed to burn pelletized wood fuel only. Do not use any other type of fuel, this will void

any warranties stated in this manual.

THE USE OF CORDWOOD IS PROHIBITED BY LAW.

Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper

combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by

adjusting the slider/damper located on the left side of the stove.

It is advisable to clean the exhaust vent bi-annually or every two tons of pellets.

The grounded electrical cord should be connected to a standard 220-240 volts, 50 hertz electrical outlet

and also must be accessible. If this power cord should become damaged a replacement power cord must

be purchased from the manufacturer or a qualified ENVIRO dealer. Be careful that the electrical cord

is not trapped under the appliance and that it is clear of any hot surfaces or sharp edges. This unit’s

maximum power requirement is 520 watts. (2.26-2.46 Amps).

Soot or creosote may accumulate when the stove is operated under incorrect conditions such as an

extremely rich burn (black tipped, lazy orange flames).

When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the

home and bolted to the floor. Make sure that the structural integrity of the home is maintained and all

construction meets local building codes.

Be sure to maintain the structural integrity of the home when passing a vent through walls, ceilings, or

roofs.

The ash pan and viewing door must be locked securely for proper and safe operation of the pellet

stove.

Introduction

IMPORTANT SAFETY DATA:

WARNINGS AND RECOMMENDATIONS:

Introduction

PELLET QUALITY:

PELLET QUALITY IS IMPORTANT, PLEASE READ THE FOLLOWING PAGE.

Your pellet stove has been designed to burn wood pellets only. Since there are many manufacturers

of wood pellets, it is important to select pellets that are free of dirt or any impurities. The Pellet Fuel

Industries (P.F.I.) has established standards for wood pellet manufactures. We recommend the use of

pellets that meet or exceed these standards. Ask your dealer for a recommended pellet type.

THE PERFORMANCE OF YOUR PELLET STOVE IS GREATLY AFFECTED BY THE TYPE AND QUALITY OF

WOOD PELLETS BEING BURNED. AS THE HEAT OUTPUT OF VARIOUS QUALITY WOOD PELLETS DIFFER,

SO WILL THE PERFORMANCE AND HEAT OUTPUT OF THE PELLET STOVE.

Since Sherwood Industries Ltd. has no control over the quality of pellets that you use, we assume no

liability caused by the quality of wood pellets used.

P.F.I. PELLET STANDARDS:

Fines ...................................1% maximum through a 1/8” screen

Bulk Density.........................40 lbs. per cubic foot minimum

Size.....................................1/4” to 3/8” diameter 1 – 1.5” long maximum

Ash Content .........................1% maximum

Moisture Content..................8% maximum

Heat Content .......................approximately 8200 Btu per lb. minimum

Check the burn-pot liner periodically to ensure that the holes are not blocked with clinkers, (clinkers are

silica in the fuel that form a hard mass during the burning process). If they are blocked, remove the liner

(when the unit is cold) and clean the clinkers out. The liner should be cleaned or scraped once every 2-3

days depending on wood pellet quality. Clean the holes in the lines with a small pointed object.

Store pellets at least 36” (1 m) away from the pellet stove.

If you have any questions with regards to your stove or the above-mentioned information, please feel

free to contact your local dealer for further clarification and comments.

Since Sherwood Industries Ltd. has no control over the installation of your stove, we grant no warranty

implied or stated for the installation or maintenance of your stove. Therefore, Sherwood Industries Ltd.

assumes no responsibility for any consequential damage.

A. Do not abuse the glass by striking or slamming the door shut.

B. Do not attempt to operate the stove with broken glass.

C. Do not attempt to open the door and clean the glass while the unit is in operation. To clean the glass,

use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner, or take a damp

paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the glass.

Introduction

D. Do not use abrasive cleaners to clean the surface or any part of the stove.

E. It is recommended that the unit be secured into its’ position in order to avoid any displacement.

F. Never use gasoline, gasoline-type lantern fuel, kerosene, or similar liquids to start the fire. Keep all

such liquids well away from the pellet stove while it is in use.

G. Disposed ashes should be placed in a metal container with a tight-fitting lid. The closed container of

ashes should be on a non-combustible floor on the ground, well away from all combustible materials

pending final disposal. The ashes should be retained in the closed container until all cinders have

thoroughly cooled before disposing of them.

H. Make sure the ash pan is closed tightly during the operation of the stove.

I. Fresh air intake is strongly recommended. Failure to install intake air may result in the unit smoking

during power failures as well as improper combustion.

NOTE: Fresh air is mandatory on all units installed in “Mobile Homes” and “Air Tight” homes.

J. GOLD BARS: Please clean all fingerprints off of all gold parts, with denatured alcohol on a soft cloth,

before firing the unit each time. Fingerprints, etc. can become permanently etched into the gold if not

removed before operating the pellet heater.

K. BRICK PANEL: The paint on the steel brick panel may peel. This is due to extreme conditions applied

to the paint and is in no way covered by warranty.

KEEP ASH PAN FREE OF RAW FUEL. DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN

ASH PAN. A fire in the ash pan could be the result.

AUTOMATIC SAFETY FEATURES OF YOUR PELLET STOVE:

A. The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F

(49°C) for Circuit Board and 140°F (60°C) for Timer Control.

B. The stove has a high temperature safety switch. If the temperature at the back of the firebox

reaches 200°F (93°C), the auger will automatically stop and the stove will shut down when the

exhaust temperature cools. If this happens, call your local dealer to reset the 200°F (93°C) high

limit switch. ALSO FIND THE REASONS WHY THE UNIT OVERHEATED.

C. The unit has a convection fan control over-ride. This function causes the convection fan to reach

its’ full speed when the temperature at the back of the firebox reaches 160°F (71°C). This is a

normal safety feature of your unit. To compensate for the fan cycling action that may occur, turn

up the blower control proportionately to the heat output.

D. If the power goes out, the unit will stop running. When the power comes back on, the stove will

not restart unless the exhaust temperature is still above 120°F (49°C) for Circuit Board and 140°F

(60°C) for Timer Control.

APPLIANCE DIMENSIONS:

Introduction

RATING LABEL LOCATION:

The rating label is located on the hopper lid.

UNIT DIMENSIONS

HEIGHT: 34 (86.68 cm)

WIDTH: 22 (55.88 cm)

DEPTH: 24 (62.23 cm)

Front View Top View

HEARTH PAD:

WIDTH: 24 (61.79 cm)

DEPTH: 24 (62.23 cm)

Operating Instructions

6. Adjusting the blower speed control knob will vary the rate of airflow into the room by varying the

speed of the convection blower.

*Note: The convection blower may cycle to high automatically, depending on the setting of the controls.

This is a normal safety feature of the unit.

TURNING OFF YOUR PELLET STOVE:

To turn your stove off, simply turn the HEAT OUTPUT knob (knob “B”) counter-clockwise until the knob

clicks to the “off” position. This will stop the feed of pellets. The blowers will continue to run and cool

the stove. When cool enough the stove will shut down.

SPECIAL NOTES: The flashing green light corresponds to the auger feed rate.

The scale on the Dial A Fire knob represents a range, not exact times. Wood pellets of differing quality

may affect the performance of the stove. If the stove has trouble operating at the ends of its’ range,

turn the heat output knob back slightly.

1. Check and fill hopper with pellets.

2. Switch on power by pushing the start-up switch

once only.

3. Turn the Dial-A-Fire knob to the 12 o’clock

position. (Lower grade pellets may need a

higher setting on the feed rate).

NOTE: unit will take longer to light if the hopper

has been completely emptied.

4. Wait until the fire is established, then turn knob

“B” to the desired heat output. (The stove may

not be able to burn in the BLUE ZONE if poor

quality wood pellets are being used.) Adjust

the Slider Damper to the appropriate setting.

5. If the stove should shut off after 15 minutes

and there is still a fire in the firebox – press

the start-up switch once more. If the fire went

out, return to step number 2 and re-light the

stove.

CONVECTION

BLOWER SPEED

CONTROL

AUGER LIGHT

START-UP

SWITCH

DIAL-A-FIRE

HEAT

OUTPUT

KNOB

HOW TO TURN ON AND OPERATE YOUR PELLET APPLIANCE (TIMER CONTROL):

AUGER TRIM

FAN

MANUAL FEED

ON/OFF

HEAT LEVEL

















CONTROL BOARD FUNCTIONS:

1. AUGER TRIM: Used to increase feed rates on

LOW ONLY for poorer quality fuels. This button

reduces or increases the ON time of the Auger

pulse on low.

2. CONVECTION BLOWER CONTROL: Used

to turn the convection blower off. Convection

blower will automatically come on when the

160° F (71° C) sensor reaches this temperature

to help cool the unit.

3. AUGER PULSE LIGHT: This light will flash in

conjunction with the auger.

4. MANUAL AUGER FEED: If the unit runs out

of fuel, this button can be used to “prime the

auger system”. This button will turn off after

60 seconds and then must be released and

pressed again.

5. SYSTEM LIGHT: Responsible for signaling

the state of the control board. If flashing, the

board is under control. If the light is solid,

setting can be altered.

TURNING PELLET STOVE ON (CIRCUIT BOARD):

WITHOUT THERMOSTAT:

Ensure the hopper has sufficient fuel or pellets to start the unit.

1. Press the ON / OFF button (6) to start the appliance. System light (5) will flash, auger light (3) will

flash with the pulse of the auger, heat level indicator will show with no control until the system light

becomes solid.

2. If this is the first time the unit has been started or the unit has run out of fuel, press the Manual Auger

Feed button (4) and hold down for 60 seconds. This will help “prime the auger,” deliver fuel to the

burn pot, and help light the unit more quickly.

3. When a fire has been established, the system light will become solid and the auger light will continue

to flash. The heat output button (8) can be pressed to achieve the desired heat setting.

6. ON/OFF BUTTON: Used to turn the unit ON and OFF.

7. HEAT OUTPUT INDICATOR: Shows the present heat output setting.

8. HEAT LEVEL ADJUSTMENT: When pressed, will change the heat setting of the unit from low to

high.

Operating Instructions

SLIDER/DAMPER OPERATION:

Operating Instructions

THE TUBE SCRAPER ROD:

Put the stainless steel rod through the hole in the heat exchanger, thread the rod into the scraper plate.

ON LOW

Push all the

way in

ON HIGH

Pull out until

an efficient

flame is

achieved

This is used to regulate the airflow through the pellet stove.

•On the low heat output settings, push the slider all the way in.

•On the high heat output pull the slider out or until a good fire is achieved. A good fire is in between a

fire with lazy, flames black tipped flames and a forced fire (very quick, shorter flames). A good fire is the

most efficient and will have a bright and active flame.

•Hot magnetic reading 0.10 – 0.

4. The convection blower (room air blower) will be on, the speed of this blower is controlled by the

setting set on the heat output indicator. The convection blower can be turned OFF by depressing the

convection blower control button (2). When the unit reaches 160° F (71° C), the convection blower will

come ON, cooling the unit. It is recommended that the convection blower be left on at all times.

5. When the unit is operating on LOW

the unit can be adjusted for poorer quality

fuels. By depressing the Auger Trim button

(1), WHEN THE UNIT IS ON LOW, the ON

time the auger pulses can be changed

from 2 seconds ON to 4 seconds ON.

AUGER TRIM

2 SECONDS

“ON”

3 SECONDS

“ON” Factory

Setting

4 SECONDS

“ON”

These settings can be used if the unit does not keep a fire going on low (poor quality fuel). These settings

could also be used if the low setting is too hot or cold for the surrounding area.

TURNING OFF YOUR PELLET STOVE:

To turn the unit OFF, simply press the ON / OFF button. All LED lights will go out. This will stop the feed

of pellets. The blowers will continue to operate and cool the stove. When cool enough, the stove will shut

down.

2-3 DAYS/WEEKLY SEASON or 2 TONS OF FUEL

Burn Pot and Liner Exhaust Vent

Ash Pan Fresh Air Intake Tube

Inside Firebox Blower Mechanisms

Door Glass Heat Exchanger Tubes

Heat Exchanger Tubes Behind Firebox Liners

Ash Pan and Door Gaskets All Hinges

Door Latch Post-Season Clean-up

Operating Instructions

ROUTINE CLEANING AND MAINTENANCE:

IGNITOR TUBE

FRESH AIR

TUBE

BURN POT

LINER

BURN POT

The following list of components should be inspected and maintained routinely to ensure that the appliance is

operating at its’ optimum and giving you excellent heat value:

BURNER POT AND LINER

This is the ‘pot’ where the pellets are burned. Every two to three days (when the unit is cold), remove the burn-

pot liner from the stove. Using a metal scrapper, remove material that has accumulated or is clogging the liner’s

holes. Then dispose of the scrapped ashes from the liner and from inside the burn-pot. Place the burn-pot back

into the stove, making sure that the pipes are properly inserted into the burn pot. Place the liner back into the

burn-pot, making sure that the ignitor hole in the liner is aligned with the ignitor tube. Push the liner up against

the ignitor tube.

To remove the burn pot and burn pot liner, open the door using the door handle provided (located on the left-

hand side of the stove). Swing the door open. Lift the liner from the burn pot. Lift the burn pot from the firebox

by gently lifting up the front of the burn pot, then sliding the assembly from the air intake tube and the ignitor

cartridge.

ASH REMOVAL:

CAUTION WHEN VACUUMING FLY ASH: BECAUSE THE FLY ASH IS VERY FINE, THE USE OF A FINE

FILTER VACUUM BAG WILL BE REQUIRED TO PREVENT ASH FROM BEING BLOWN BACK INTO THE

ROOM. Please pay special attention that there are no hot ashes in the firebox or there could be a possibility of

a fire hazard inside the vacuum cleaner. Place all hot ashes into a noncombustible container.

FREESTANDING ASH PAN:

This part is located under the burner, in the pedestal, and has a latching mechanism to secure it. To remove the

ash pan, unlock the latch on the pedestal cover and pull the pan out. Dump the ashes into a metal container

stored away from combustibles. Monitor the ash level every week. Remember that different pellet fuels will

have different ash contents. Ash content is a good indication of fuel efficiency and quality. Refer to “Warnings

and Recommendations” for disposal of ashes.

DO NOT PLACE UNBURNED OR RAW PELLET FUEL IN ASH PAN

BLOWER MECHANISMS:

Unplug the stove then open the right/left side panels to access the two blowers. Only the convection blower

motor (on the right side of the stove) will require lubrication. The convection motor has two lubrication holes

on it. Use two drops of SAE 20, light oil to lubricate every six months. Excess oil may damage the motor. The

TOOLS REQUIRED TO CLEAN UNIT:

Torx T-20 Screwdriver, 5/16” wrench or

socket, Brush, Soft Cloth, Vacuum with fine

filter bag

ASH PAN AND DOOR GASKETS

After excessive use, the gasketing may come

loose. To repair this, glue the gasketing on

using high-temperature fiberglass gasket

glue available from your local dealer. This is

important to maintain an airtight assembly.

DO NOT PLACE UNBURNED OR RAW

PELLET FUEL IN ASH PAN.

Andere Handbücher für Alliance EF3

Inhaltsverzeichnis

Andere Enviro Pelletofen Handbücher

Enviro

Enviro P3 Bedienungsanleitung

Enviro

Enviro Milan Bedienungsanleitung

Enviro

Enviro WINDSOR Bedienungsanleitung

Enviro

Enviro EF THERMO Bedienungsanleitung

Enviro

Enviro Empress Bedienungsanleitung

Enviro

Enviro MERIDIAN 50-830 Bedienungsanleitung

Enviro

Enviro EF-V EVOLUTION Bedienungsanleitung

Enviro

Enviro M55C-FPI Bedienungsanleitung

Enviro

Enviro EF2 Bedienungsanleitung

Enviro

Enviro Maxx Bedienungsanleitung

Enviro

Enviro Mini A Bedienungsanleitung

Enviro

Enviro EF-IV I Bedienungsanleitung

Enviro

Enviro EF THERMO 28 CE2005 Bedienungsanleitung

Enviro

Enviro Evolution EF5 Bedienungsanleitung

Enviro

Enviro Empress Bedienungsanleitung

Enviro

Enviro WINDSOR Bedienungsanleitung

Enviro

Enviro Omega Bedienungsanleitung

Enviro

Enviro BERN C-10629 Bedienungsanleitung

Enviro

Enviro Maxx-1 Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Enviro

Enviro MINI C-14593 Bedienungsanleitung

Enviro

Enviro Meridian C-10135 Bedienungsanleitung

Enviro

Enviro Omega Bedienungsanleitung

Enviro

Enviro Evolution-A Bedienungsanleitung

Beliebte Pelletofen Handbücher anderer Marken

SMG

SMG Comfort Bilt HP50GC Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Palazzetti

Palazzetti JP Series Installationsanleitung

Travis Industries

Travis Industries Avalon 900 PS Bedienungsanleitung

Flame

Flame FP-45 Bedienungsanleitung

Astra

Astra P-7 Bedienungsanleitung

Heatilator

Heatilator ECO-ADV-PS35 Bedienungsanleitung

Cadel

Cadel aquos 24 h2O Bedienungsanleitung

vicenza

vicenza V4.5 Bedienungsanleitung

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Technisches Handbuch

Quadra-Fire

Quadra-Fire 1000 Gold Betriebsanleitung

Ferroli

Ferroli GEMMA Bedienungsanleitung

pleasant hearth

pleasant hearth PH35PS Series Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200M-MBK Bedienungsanleitung

England's Stove Works

England's Stove Works 25-EP Bedienungsanleitung

Avalon

Avalon Astoria Bedienungsanleitung

Spartherm

Spartherm Mellino Kurzanleitung