Enviro EF2 Bedienungsanleitung

November 2011

Enviro EF2 Classic

Wood Pellet Fire FPI CB and FS CB

Classic Wood Pellet Burning Heater

Insert and Free Standing Models

Installation Specications

Safety testing of the EF2 Classic FS CB Pellet Burning Heater to

AS/NZS 2918, ARS 09/1981 & 08/1902. Emissions 07/1731

Safety testing of the EF2 Classic FPI CB Pellet Burning Heater to

AS/NZS 2918, ARS 09/1981 & 09/1952, 09/1953. Emissions 07/1713

Flue Kit Testing to AS/NZS 2918 AppF: 05/1185

November 2011

Installation

Dimensions – Classic Freestanding

Dimensions - Classic Insert & Built-In Heater

597 mm

525 mm 556 mm

767 mm

FPI (612 mm)

333 mm

559 mm

FPI

579 mm

November 2011

Installation Clearances & Specications

Minimum clearances shown are in millimetres. All Enviro res are tested to AS/NZS2918:2001.

Specications were correct at time of printing but may alter and those detailed below should be used as

a guide only. Refer to the Installation and Operation Manual supplied with every Enviro Pellet Fire or if

in doubt, consult your Switch Retailer. Refer to Safety Test 09/1981 for all clearances to combustibles.

Clearances to Combustibles

Internal Flue (Freestanding)

Built-In Fire and Flue

Internal Flue

External Flue (Freestanding)

Clearances to Combustibles

Classic Pellet Fire

(built-in & freestanding)

Freestanding

Clearances

Built-In Heater

Clearances

Location Dimension

(mm)

A 100

B 150

C* 50

D ~210

E N/A

F 75

G* 50

H 100

I* 50

J* 25

Location Dimension

(mm)

K 100

L 920

M#1020

N 150

O#150

P* 50

NOTE: Built-In re clearances don’t apply in a non-combustible cavity. However, remember you will need access for servicing. The above clearance to

combustibles on the ue are only applicable within the re envelope. Clearance outside this e.g.at a ceiling / wall thimble reverts to 25mm as per ARS ue test

05/1185. Correct as at November 2011. # Fire hearth width indicative only. Critical measurement is “O”, extending in front of the re. Hearth width only needs to

be same as re width.

* from shielded ue

Note: AS/NZS 2918

requires a minimum

of 100mm clearance

for any side requiring

access.

Note: These are

minimum clearances to

combustibles. Actual

installation distances

may be greater.

WALL WALL WALL WALL WALL WALL WALL

LWALL WALL WALL WALL WALL WALL WALL WALL

November 2011

Location of the Pellet Fire

Installation of the Enviro Classic Wood Pellet Burning Heater should be undertaken by an

experienced installer. Please read the Classic Owners/Technical Manual thoroughly before

commencing installation as failure to follow the instruction could cause damage to the pellet

re or property.

Positioning the re:

Generally the Classic should be installed in a centrally located position within the home. When

deciding where to position the appliance in your room you need to consider the following:

• Location of a power source

• The Classic has a convection fan which blows air through tubes in the direction that the

re faces, for optimum performance this location should be in a large room centrally

located.

• The Classic must be installed on a non-combustible surface. This surface must protrude

150mm from the front of the closed pellet re door.

• The Classic has been Safety Tested to AS/NZS 2918 using the Davins manufactured

ue. Test Report ARS 05/1185. Installation is not exclusive to these nominated kits,

though alternative ue should only be considered following consultation with your local

council.

• Please consult page 3 for the required clearances to combustible material also ensure

the position of structural elements near the proposed ue.

• Because of the positive pressure in the ue, sealing of all 75mm stainless joints is

mandatory – use high temperature sealant. Both inner and outer ue joints must be

riveted.

• Seismic Restraint: Please see page 9 for requirements.

• Warranty: To validate warranty following installation a copy of the completed Warranty

Registration Form/Producer’s Statement must be forwarded to: Switch - Fax (03) 341

8057.

November 2011

Internal Standard Flue Kit (50)

Internal Standard Flue Kit

Each 50 Internal Standard Flue Kit contains:-

ytitnauQnoitpircseDoNtraP

1Galvanised outer liner

ø100mm x 900mm long 1

2 Stainless steel inner liner

ø75mm x 900mm long

4a Black p/coat outer liner

ø100mm x 900mm long

5Inner/outer ue liner spacer

6c Ceiling thimble ø107mm hole

7c Ceiling decor plate

ø107mm hole – white

8Rain cap 75mm

9Rain Cap 100mm

10b Elbow 45° – ø75mm stainless

–black (painted)

12H T-adaptor/cleanout – ø75mm

–black (painted)

23 Support angle 950mm long

– 50mm x 50mm sides

This ue kit may be used in new and replacement

applications in rooms with stud height of 2.4m. The

overall height of the ue is 3.6m. The visible u e is

nished in black and the ceiling plate is white. T he

support angles for securing the liner to the ceilin g are

not shown. Kit is supplied in a carton.

Heat-resistant

oor protector

Seismic restraint

(to be tted)

50mm minimum clearance if lined ue

600mm from

roof

penetration

~210 mm

150mm

(minimum)

Note: The Davin 50 Internal Standard Flue

Kit complies with AS/NZS 2918:2001 as per

Applied Research Test Report 05/1185, dated

15 September 2005.

All res must be installed by a qualied

installer as per the manufacturer’s

instructions and AS/NZS2918:2001.

To order : Telephone 0800 765 431. Fax 64 3 341 8057 info@switchenergy.co.nzwww.switchenergy.co.nzDecember 2006

Drawing representative only - not to scale.

This ue kit may be used in new and replacement

applications in rooms with stud height of 2.4m.

The overall height of the ue is 3.6m. The visible

ue is nished in black and the ceiling plate is

white. The support angles for securing the liner to

the ceiling are not shown. Kit is supplied in carton.

November 2011

External Standard Flue Kit (51)

Each 51 External Standard Flue Kit contains:-

ytitnauQnoitpircseDoNtraP

1Galvanised outer liner

ø100mm x 900mm long

2 Stainless steel inner liner

ø75mm x 900mm long

5Inner/outer ue liner spacer

6w Wall thimble – 2 pieces

ø102mm holes

6s Sot thimble ø107mm hole

7w Wall decor plate

ø102mm hole – white

8Rain cap 75mm

9Rain Cap 100mm

26 Lined T-adaptor

This ue kit may be used in new and replacement

applications with the ue penetrating the wall behind

the re, running vertically up an outside wall and

penetrating the sot. The overall height of the f lue is

3.6m. All visible ue has a galvanised nish, and can be

powdercoated on request. Kit is supplied in a carton.

Note: The Davin 51 External Standard Flue

Kit complies with AS/NZS 2918:2001 as per

Applied Research Test Report 05/1185, dated

15 September 2005.

All res must be installed by a qualied

installer as per the manufacturer’s

instructions and AS/NZS2918:2001.

Heat-resistant

oor protector

Seismic restraint

(to be tted)

600mm from

roof penetration

100mm

(minimum)

150mm

(minimum)

External Standard Flue Kit51

To order :December 2006 Telephone 0800 765 431. Fax 64 3 341 8057 info@switchenergy.co.nzwww.switchenergy.co.nz

Drawing representative only - not to scale.

This ue kit may be used in new and replacement

applications with the ue penetrating the wall

behind the re, running vertically up an outside

wall and penetrating the soft. The overall

height of the ue is 3.6m. All visible ue has a

galvanised nish, and can be powdercoated on

request. Kit is supplied in a carton.

November 2011

Insert Flue Kit (52)

Each 52 Insert Flue Kit contains:-

ytitnauQnoitpircseDoNtraP

2 Stainless steel inner liner

ø75mm x 900mm long 5

8Rain cap 75mm 1

12 T-adaptor/cleanout – ø75mm 1

16 Clamp – exible ue to

stainless ue pipe 1

19 Flexible ue pipe – stainless

steel ø75mm x 1m 1

21 Bracket 75mm securing

ue pipe to wall 1

839 Casing cover – standard

ø75mm - ø300mm 1

34 Chimney cover – may be required

as an optional extra

This ue kit may be used in replacement applications

in masonry chimneys. The overall height of the ue is

4.5m. Kit is supplied in two cartons.

Note: The Davin 52 Insert Flue Kit

complies with AS/NZS 2918:2001 as per

Applied Research Test Report 05/1185,

dated 15 September 2005.

All res must be installed by a qualied

installer as per the manufacturer’s

instructions and AS/NZS2918:2001.

Heat-resistant

oor protector

Seismic restraint chain. To be tted one on each

side of the re at the mid point. The chain should

have a breaking strength of at least 350kg or

minimum 3.5mm nominal diameter. Chains

should be anchored to the oor (not framing or

masonry), and should be as short as possible,

only allowing access to unbolt the chains from the

re to allow the re to be pulled forward for servicing.

Chimney cover

– optional extra

150mm

(minimum)

Insert Flue Kit52

To order :December 2006 Telephone 0800 765 431. Fax 64 3 341 8057 info@switchenergy.co.nzwww.switchenergy.co.nz

Drawing representative only - not to scale.

November 2011

Built In Heater (non-chimney) Flue Kit (54)

Each 54 Built-in-Heater Flue Kit

(non-Chimney installation) contains:-

ytitnauQnoitpircseDoNtraP

Galvanised outer liner

ø100mm x 900mm long

Stainless steel inner liner

ø75mm x 900mm long

Inner/outer ue liner spacer

Ceiling thimble ø107mm hole

Rain cap 75mm

Rain cap 100mm

Elbow 45° – ø75mm stainless

–black (painted)

T-adaptor/cleanout – ø75mm

This ue kit may be used in new or existing timber

chimneys. The overall height of the ue is 3.6m.

Kit is supplied in a carton.

Note: The Davin 54 Built-in-Heater Flue Kit

(non-Chimney) complies with AS/NZS

2918:2001 as per Applied Research Test

Report 05/1185, dated 15 September 2005.

All res must be installed by a qualied

installer as per the manufacturer’s

instructions and AS/NZS2918:2001.

600mm from

roof

penetration

Built-in-Heater Flue Kit

(non-Chimney installation)

To order :December 2006

10b

50mm minimum clearance if lined ue

150mm

(minimum)

Heat-resistant

oor protector

Seismic restraint

(to be tted)

Telephone 0800 765 431. Fax 64 3 341 8057 info@switchenergy.co.nzwww.switchenergy.co.nz

Drawing representative only - not to scale.

November 2011

Flashing Options:

Decktite - For all Steel Roof Proles

Please circle the ashing option to be used. When considering an alternative method please consult

your local council.

Seismic Restraint

Concrete Floor

Installation scenarios for the Classic FS and Built In Models require the use of hold-down anchors (one

on each side)

Fixing to Concrete Floor:

Minimum M8 expansion anchors (M10 recommended) or min M8 epoxy- set anchors.

Approved Anchors: Expansion Anchors-Ramset Dynabolt and Trubolt, Hilti HAS.

Epoxy-set Anchors – Ramset Epcon, Ramset Chemset and Hilti HVU.

Installation of the Insert Model (non-combusitble cavity) requires the use of a seismic restraint chains to

be tted one on each of the re at the mid-point. The chain should have a breaking strength of at least

350kg or minimum 3.5mm nominal diameter. Chains should be anchored to the oor (not framing or

masonry), and should be as short as possible, only allowing access to unbolt the chains from the re to

allow the re to be pulled forward for servicing.

Timber Floor

Minimum 14g x 60mm screws (6.3mm diameter) or M10 X 90mm coach-screws. These shall be xed

a minimum of 40mm into the centre-line of the existing oor joists. If screws cannot be installed directly

into an existing oor joist, solid blocking between joists (min size 90x45) shall be provided.

Andere Handbücher für EF2

Inhaltsverzeichnis

Andere Enviro Pelletofen Handbücher

Enviro

Enviro P3 Bedienungsanleitung

Enviro

Enviro Empress Bedienungsanleitung

Enviro

Enviro OLYMPIAN Bedienungsanleitung

Enviro

Enviro MERIDIAN Bedienungsanleitung

Enviro

Enviro Maxx-1 Bedienungsanleitung

Enviro

Enviro M55C-FPI Bedienungsanleitung

Enviro

Enviro EF-IV I Bedienungsanleitung

Enviro

Enviro Milan Bedienungsanleitung

Enviro

Enviro Meridian 50-765 Bedienungsanleitung

Enviro

Enviro MAX 50-1531 Bedienungsanleitung

Enviro

Enviro Omega Bedienungsanleitung

Enviro

Enviro Meridian C-10135 Bedienungsanleitung

Enviro

Enviro P3 Bedienungsanleitung

Enviro

Enviro M-55C-FS Bedienungsanleitung

Enviro

Enviro Maxx-1 Bedienungsanleitung

Enviro

Enviro Mini A Bedienungsanleitung

Enviro

Enviro 50-1021 Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Enviro

Enviro M-55C-FS Bedienungsanleitung

Enviro

Enviro Omega Bedienungsanleitung

Enviro

Enviro M-55-FS Bedienungsanleitung

Enviro

Enviro Empress-1 FS Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Beliebte Pelletofen Handbücher anderer Marken

SMG

SMG Comfort Bilt HP50GC Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Palazzetti

Palazzetti JP Series Installationsanleitung

Travis Industries

Travis Industries Avalon 900 PS Bedienungsanleitung

Flame

Flame FP-45 Bedienungsanleitung

Astra

Astra P-7 Bedienungsanleitung

Heatilator

Heatilator ECO-ADV-PS35 Bedienungsanleitung

Cadel

Cadel aquos 24 h2O Bedienungsanleitung

vicenza

vicenza V4.5 Bedienungsanleitung

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Technisches Handbuch

Quadra-Fire

Quadra-Fire 1000 Gold Betriebsanleitung

Ferroli

Ferroli GEMMA Bedienungsanleitung

pleasant hearth

pleasant hearth PH35PS Series Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200M-MBK Bedienungsanleitung

England's Stove Works

England's Stove Works 25-EP Bedienungsanleitung

Avalon

Avalon Astoria Bedienungsanleitung

Spartherm

Spartherm Mellino Kurzanleitung