Enviro EP3 Bedienungsanleitung

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE



SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED

PAPER.

50-1070

PELLET STOVE

EF3

OWNER’S MANUAL

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION

AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO

FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY

DAMAGE, BODILY INJURY, OR EVEN DEATH.

Contact your building or fire officials about restrictions and

installation inspection requirements in your area.

Freestanding, Fireplace Insert,

and Built-In Heater

Table of Contents

Introduction..............................................................................................................3

Rating Label Location......................................................................................3

Pellet Quality..................................................................................................3

Important Safety Data....................................................................................4

Safety Warnings And Recommendations...........................................................4

Operating Instructions...............................................................................................7

Operating Your Pellet Stove - Timer..................................................................7

Turning Your Pellet Stove Off - Timer................................................................7

Stove Controls - Circuit Board..........................................................................8

Operating Your Pellet Stove - Circuit Board.......................................................9

Turning Your Pellet Stove Off - Circuit Board.....................................................9

Routine Cleaning and Maintenance...........................................................................10

Warranty.................................................................................................................13

Installation Data Sheet.............................................................................................14

Introduction

* This manual is designed for the home owner in conjunction with the technical manual. *

RATING LABEL LOCATION:

Freestanding: The rating label is located on the inside of the hopper lid.

Fireplace Insert and Built-In Heater: The rating label is located on the hopper cover.

PELLET QUALITY:

Pellet quality is important, please read the following:

Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other

type of fuel, as this will void any warranties stated in this manual.

The performance of your pellet stove is greatly affected by the type and quality of wood

pellets being burned. As the heat output of various quality wood pellets differs, so will the

performance and heat output of the pellet stove.

CAUTION: It is important to select and use only pellets that are dry and free of dirt or any impurities

such as high salt content. Dirty fuel will adversely affect the operation and performance of the unit and

will void the warranty.

ASH: The ash content of the fuel and operation of your stove will directly determine the frequency of

cleaning. The use of high ash fuels may result in the stove needing to be cleaned daily. A low ash fuel

may allow longer intervals between cleaning.

CLINKERING: [clinkers are silica (sand) or other impurities in the fuel that will form a hard mass during

the burning process]. This hard mass will block the air flow through the Burn Pot Liner and affect the

performance of the stove. Any fuel, even approved types, may tend to clinker. Check the Burn-Pot Liner

daily to ensure that the holes are not blocked with clinkers. If they become blocked, remove the liner

(when the unit is cold) and clean/scrape the clinkers out. Clean the holes with a small pointed object if

required. Refer to the section Routine Cleaning and Maintenance.

PELLET FEED RATES: Due to different fuel densities and sizes, pellet feed rates may vary. This may

require an adjustment to the slider damper setting or to the auger feed trim setting on Low.

Since Sherwood Industries Ltd. has no control over the quality of pellets that you use, we assume no

liability for your choice in wood pellets.

Store pellets at least 36” (1 m) away from the pellet stove.

IMPORTANT SAFETY DATA:

Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet

Stove. Failure to follow these instructions may result in property damage, bodily injury

or even death. Contact your local building or fire official to obtain a permit and any information on

installation restrictions and inspection requirements for your area.

To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the

installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information with

regards to your local building codes and installation restrictions.

The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive

chimney pressure. It is very important to ensure that the exhaust system be sealed and airtight. The ash

pan and viewing door must be locked securely for proper and safe operation of the pellet stove.

Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper

combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by

adjusting the slider damper located on the left side of the stove.

Minor soot or creosote may accumulate when the stove is operated under incorrect conditions such as an

extremely rich burn (black tipped, lazy orange flames).

If you have any questions with regard to your stove or the above-mentioned information, please feel free

to contact your local dealer for further clarification and comments.

SAFETY WARNINGS AND RECOMMENDATIONS:

Caution: Do not connect to any air distribution duct or system.

Do not burn garbage or flammable fluids such as gasoline, naptha or engine oil.

Unit hot while in operation. Keep children, clothing and furniture away. Contact

may cause skin burns.

FUEL: This pellet stove is designed and approved to only burn wood pellet fuel with up to 3% ash

content. Dirty fuel will adversely affect the operation and performance of the unit and may void the

warranty. Check with your dealer for fuel recommendations.

THE USE OF CORDWOOD IS PROHIBITED BY LAW.

SOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which

will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the

house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/

damper as needed to ensure proper combustion. See: “SLIDER/DAMPER SETTING”.

CLEANING: There will be some build up of fly ash and small amounts of creosote in the exhaust. This

will vary due to the ash content of the fuel used and the operation of the stove. It is advisable to inspect

and clean the exhaust vent semi-annually or every two tons of pellets.

Introduction

ASHES: Disposed ashes should be placed in a metal container with a tight-fitting lid. The closed

container of ashes should be on a non-combustible floor on the ground, well away from all combustible

materials pending final disposal. The ashes should be retained in the closed container until all cinders

have thoroughly cooled before disposing of them.

ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be

grounded. The grounded electrical cord should be connected to a standard 220-240 volts (2.26-2.46

Amps), 50 hertz electrical outlet and also must be accessible. If this power cord should become damaged,

a replacement power cord must be purchased from the manufacturer or a qualified ENVIRO dealer. Be

careful that the electrical cord is not trapped under the appliance and that it is clear of any hot surfaces

or sharp edges. This unit’s maximum power requirement is 520 watts.

GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove

with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an ENVIRO

dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is

hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner,

or take a damp paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the

glass.

FLAMMABLE LIQUIDS: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter

fluid, or similar liquids to start or “freshen up” a fire in the heater. Keep all such liquids well away from

the heater while it is in use.

SMOKE DETECTOR: Smoke detectors should be installed and maintained in the structure when

installing and operating a pellet burning appliance.

OPERATION: The ash pan and door must be closed securely for proper and safe operation of the pellet

stove. Also ensure all gaskets on the door are checked and replaced when necessary.

KEEP ASH PAN FREE OF RAW FUEL.

DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN ASH PAN. A fire in the ash pan may occur.

If you have any questions with regards to your stove or the above-mentioned information, please feel

free to contact your local dealer for further clarification and comments.

SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF

YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED

FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, SHERWOOD

INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

Operating Instructions

AUTOMATIC SAFETY FEATURES:

Your pellet Stove has the following safety features:

A. The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F

(49°C).

B. The stove has a high temperature safety switch. If the temperature on the hopper reaches 200°F

(93°C), the auger will automatically stop and the stove will shut down when the exhaust temperature

cools. If this happens, call your local dealer to reset the 200°F (93°C) high limit switch. ALSO FIND

THE REASONS WHY THE UNIT OVERHEATED.

C. The unit has a convection fan control over-ride. This function causes the convection fan to reach its full

speed when the temperature at the back of the firebox reaches 160°F (71°C). This is a normal safety

feature of your unit. To compensate for the fan cycling action that may occur, turn up the blower

control proportionately to the heat output.

D. If the power goes out, the unit will stop running. When the power comes back on, the stove will not

restart unless the exhaust temperature is still above 120°F (49 °C).

SLIDER/DAMPER SETTING:

This is used to regulate the airflow through the pellet stove.

Circuit Board Model: A Qualified Service Technician or Installer should set the Slider Damper.

SPECIAL NOTES:

  

 

 

 



 



 

Figure 2: Slider /

damper positions.

Pellet quality is a major factor in how the Pellet stove will operate. If the pellets have

a high moisture content or ash content the fire will be less efficient and has a higher

possibility of the fire building up and creating clinkers (hard ash build-up).

If the fire should happen to go out and the Dial-A-Fire has been set on the lowest

setting, the Slider Damper should be pushed in slightly, decreasing the air in the

firebox or the Dial-A-Fire and Auger Trim can be turned up slightly.

If, after long periods of burning, the fire builds up and overflows the burn pot or

there is a build up of clinkers, this would be a sign that the pellet quality is poor,

this requires more primary air, the slider damper must be pulled out to compensate.

Pulling the slider damper out gives the fire more air.

The easiest way to make sure that an efficient

flame is achieved is to understand the

characteristics of the fire.

• A tall, lazy flame with dark orange tips,

requires more air – Open slider (pull out)

slightly.

• A short, brisk flame, like a blowtorch, has too

much air – Close slider (push in) slightly.

• If the flame is in the middle of these two

characteristics with a bright yellow/orange,

active flame with no black tips then the air is

set for proper operation.

Figure 1: Efficient Flame.

Operating Instructions

Figure 3: Dial-A-Fire control panel.

1. Check and fill hopper with pellets.

2. Make sure unit is plugged into a working outlet.

3. Switch the power “ON” by pushing the start-up switch once

only.

4. Turn knob “B” to the 12 o’clock position. (Lower grade

pellets may need a higher setting on the feed rate).

NOTE: Unit will take longer to light if the hopper has been

completely emptied or is the first fire up.

5. Wait until the fire is established, then turn “Knob B” to the

desired heat output. The stove may not be able to burn in the

BLUE ZONE if poor quality wood pellets are being used. Adjust

the slider-damper to the appropriate setting (see “SLIDER/

DAMPER SETTING” section.

6. If the stove should shut off after fifteen (15) minutes and

there is still a fire in the firebox – press the start-up switch

once more. If the fire went out, return to step 2 and re-light

the stove.

KNOB “A”: Fan Controller. By adjusting the knob you will vary

the rate of airflow into the room by varying the speed of the convection blower. When you first start the

stove, it should be placed in the “OFF” position in order to heat the unit as quickly as possible. Once the

room has come up to temperature, the control may be set to a comfortable level. *Note: The convection

blower may cycle to high automatically depending on the setting of knobs “A” and “B”. This is a normal

safety feature of the unit.

SPECIAL NOTES: The flashing green light corresponds to the auger feed rate.

The scale on the Dial A Fire knob represents a range, not exact times. Wood pellets of differing quality

may affect the performance of the stove. If the stove has trouble operating at the ends of its’ range,

turn the heat output knob back slightly.

KNOB “B”: Dial a Fire Heat Output Knob. This knob controls the amount of heat output. The dial has a

scale with the blue zone representing the coolest setting of the stove, and the red zone representing

the hottest setting. The scale on knob “B” represents a range, not exact at times or fuel quantities.

Wood pellets of differing quality may affect the performance of the stove. If the stove has trouble

operating at either end of its range, turn the heat output knob back slightly.

TURNING YOUR PELLET STOVE OFF - TIMER:

To turn your stove off, simply turn the HEAT OUTPUT knob (“Knob B”) counter-clockwise until the knob

clicks to the “OFF” position. This will stop the feed of pellets. The blowers will continue to run and cool

the stove. When cool enough, the stove will shut down. DO NOT unplug unit while combustion

fan is operating. This may lead to smoke escaping from the stove.

Circuit Board Only: The combustion blower determines the adjustment of air from high fire to low fire.

The combustion exhaust blower is a variable speed blower controlled by the heat output. When the heat

output is turned down the blower speed will slow, decreasing the airflow through the firebox. As the heat

output knob is turned up, the blower speed increases drawing more air through the firebox.

OPERATING YOUR PELLET STOVE - TIMER:

Auger Trim Auger Trim Auger Trim

2 Seconds

"ON"

3 Seconds

"ON"

Factory Setting

4 Seconds

"ON"

AUGER TRIM

FAN

MANUAL FEED

ON/OFF

HEAT LEVEL

















3. AUGER PULSE LIGHT: This light will flash in

conjunction with the auger.

4. MANUAL AUGER FEED: If the unit runs out

of fuel, this button can be used to “prime the

auger system”. This button will turn off after 60

seconds and then must be released and pressed

again.

5. SYSTEM LIGHT: Responsible for signaling

the state of the control board. When the light

is flashing during start-up, the stove is in an

automatic start mode. When the light is solid,

the Heat Level Setting can be altered.

6. ON/OFF BUTTON: Used to turn the unit ON

and OFF.

7. HEAT OUTPUT INDICATOR: Shows the

present heat output setting.

8. HEAT LEVEL ADJUSTMENT: When pressed,

will change the heat setting of the unit from low

to high.

Operating Instructions

STOVE CONTROLS - CIRCUIT BOARD:

1. AUGER TRIM: Used to change feed rates on LOW ONLY for poorer quality fuels. Push the Auger

Trim button until the number 1 and 5 lights appear on the Heat Level Indicator. This will increase the

feed rate to 4 seconds ON time Auger pulse. This is done only on LOW to allow the burning of poor

quality fuels. Push the button until the number 1 and 4 lights appear, this will reduce the Auger On

time to 2 second. This setting is for high-grade fuel only. Push the button until just the number 1

light is on, this is for a three (3) second on time (standard setting).

2. CONVECTION BLOWER CONTROL: Used to turn the convection blower ON/OFF. If the Blower

is left off, and the sensor located on the air jacket reaches 160 °F (71 °C), the Convection blower

will automatically come on HI speed to cool the unit. Leave the convection blower ON for peak

efficiency

Figure 4: Circuit board control panel.

Figure 5: Auger trim and heat level indicator.

Operating Instructions

OPERATING YOUR PELLET STOVE - CIRCUIT BOARD:

PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed properly

against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit.

DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN AJAR

MANUAL MODE:

To START: Press the ON / OFF button. The stove will turn on. The system light will flash. The Auger

Light will flash with each pulse of the auger (the Auger Feed Rate is pre-programmed during start-up).

The Heat Level Indicator will show the Heat Level that the stove will run at after start-up.

If this is the first time the unit has been started or the unit has run out of fuel, the auger will need to

be primed. Press the Manual Auger Feed button until fuel starts to drop into the Burn Pot Liner (see

“OPERATING INSTRUCTIONS; STOVE CONTROLS - CIRCUIT BOARD”).

To OPERATE: When a fire has been established, the System Light will turn solid, the Auger Light will

continue to flash to the corresponding Heat Level setting. The Heat Level button can now be pressed to

change the desired Heat Level Output setting.

The convection blower (room air blower) will turn on. The speed of this blower is controlled by the setting

of the heat level output indicator. The convection blower can be turned OFF by depressing the convection

blower control button. When the air jacket reaches 160 °F (71 °C) the convection blower will come ON

High, cooling the unit. For the best efficiency and to prevent cycling, the convection blower should be

left on at all times.

When operating on LOW HEAT LEVEL, the feed rate can be adjusted, using the auger trim, for different

quality fuels. These settings can be used if the fire keeps going out on low (poor quality fuel). Or if the

low setting is too hot for the room (see “OPERATING INSTRUCTIONS; STOVE CONTROLS - CIRCUIT BOARD”).

THERMOSTAT / SWITCH MODE:

INITIAL START-UP: See above

OPERATION - HI / LOW mode: When the thermostat contacts are closed the stove settings are

adjustable as per Manual Mode (see above). When the thermostat contacts open, the circuit board will

take control of the settings. The stove will drop down to a low burn until the thermostat contacts close

again. This low burn setting can be adjusted for different fuel qualities (see “OPERATING INSTRUCTIONS;

STOVE CONTROLS - CIRCUIT BOARD”). The stove will come back to the previous HEAT LEVEL setting when the

thermostat contacts close again.

OPERATION – ON / OFF mode: When the thermostat contacts close, the unit will light automatically.

Once up to temperature, the stove operates the same as in manual mode (see above). When the

thermostat contacts open, the unit automatically begins its shutdown routine. The stove will re-light

when the thermostat contacts close again.

TURNING YOUR PELLET STOVE OFF - CIRCUIT BOARD:

•MANUAL and HI / LOW mode: To turn the unit OFF, simply press the ON / OFF button. This will stop the

feed of pellets. The blowers will continue to operate and cool the stove down. When cool enough, the

stove will turn off.

•ON / OFF mode: To turn the unit OFF, turn the thermostat down or off.

DO NOT unplug unit while Combustion fan is operating.

This may lead to smoke escaping from the stove.

Routine Cleaning and Maintenance

NOTE: Do not use abrasive cleaners to clean the surface or any part of the stove.

The following should be inspected periodically to ensure that the appliance is operating at its optimum

and giving you excellent heat value:

2-3 Days / Weekly Bi-Annually or 2 Tons of Fuel

Burn Pot and Liner Exhaust Vent

Ash Pan Fresh air Intake Tube

Inside Firebox Blower Mechanisms

Door Glass Heat exchanger tubes

Heat exchanger tubes Behind firebox liners

Ash pan & Door gaskets All Hinges

Door Latch Post Season Clean-up

BURN POT AND LINER (2-3 days)

This is the ‘pot’ where the pellets are burned. The burn pot and liner should be inspected every two to

three days, to ensure proper air flow through the liner. Failure to keep the liner clean may cause

a build up of fuel past the burn pot liner and up the drop tube. This will cause the auger to

jam and may result in pellets burning in the drop tube and hopper.

Ensure the unit is cold before cleaning. To remove the burn pot and burn pot liner, open the door using

the door handle provided, located on the left-hand side of the stove. Swing the door open. Lift the

liner from the burn pot. Lift the burn pot from the firebox by gently lifting the front of the burn pot up

first, then sliding the assembly from the air intake tube and the ignitor cartridge. Using a metal scraper,

remove material that has accumulated or is clogging the liner’s holes. Then dispose of the scrapped ashes

from the liner and from inside the burn pot. Place the burn pot back into the stove, making sure that the

pipes are properly inserted into the burn pot and the front tabs are placed in the firebox. Place the liner

back into the burn-pot making sure that the ignitor hole in the liner is aligned with the ignitor tube. Push

the liner up against the ignitor tube.

● If, after long periods of burning, the fire continually

builds up and overflows the burn pot or there is a build up

of clinkers, this is an indication that the pellet fuel quality

is poor or the stove may need cleaning. Check the stove

for ash build up (clean if required) and adjust the slider /

damper to produce the proper clean combustion.

INSIDE FIREBOX (2-3 days)

For bi-weekly clean out, ash may be removed from behind the steel plates by rotating the circular cover

to allow vacuuming behind the plates.

ASH PAN AND DOOR GASKETS (weekly)

After extended use the gasket may come loose. To repair or replace this, glue the gasket on, using high-

temperature fiberglass gasket glue available from your local ENVIRO dealer. This is important to maintain

an airtight assembly.

 



 







 

TOOLS REQUIRED TO CLEAN UNIT

• Torx T-20 Screwdriver

• 5/16” Wrench or Socket,

• Brush,

• Soft Cloth

• Vacuum with fine filter bag

The following list of components should be

inspected and maintained routinely to ensure

that the appliance is operating at its optimum

and giving you excellent heat value:

Figure 6: Burn pot with liner.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Enviro Pelletofen Handbücher

Enviro

Enviro Milan Bedienungsanleitung

Enviro

Enviro Bern Bedienungsanleitung

Enviro

Enviro Omega Bedienungsanleitung

Enviro

Enviro Evolution-A Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Enviro

Enviro Milan Bedienungsanleitung

Enviro

Enviro Maxx-1 Bedienungsanleitung

Enviro

Enviro 50-1021 Bedienungsanleitung

Enviro

Enviro Mini A Bedienungsanleitung

Enviro

Enviro P4 Bedienungsanleitung

Enviro

Enviro MERIDIAN Bedienungsanleitung

Enviro

Enviro Evolution Bedienungsanleitung

Enviro

Enviro M-55C-FS Bedienungsanleitung

Enviro

Enviro EF-II I Bedienungsanleitung

Enviro

Enviro Omega Bedienungsanleitung

Enviro

Enviro Maxx-1 Bedienungsanleitung

Enviro

Enviro Mini A Bedienungsanleitung

Enviro

Enviro WINDSOR Bedienungsanleitung

Enviro

Enviro P3 Bedienungsanleitung

Enviro

Enviro EF2 Bedienungsanleitung

Enviro

Enviro MERIDIAN 50-830 Bedienungsanleitung

Enviro

Enviro MERIDIAN Bedienungsanleitung

Enviro

Enviro WINDSOR Bedienungsanleitung

Enviro

Enviro M-55-FS Bedienungsanleitung

Beliebte Pelletofen Handbücher anderer Marken

SMG

SMG Comfort Bilt HP50GC Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Palazzetti

Palazzetti JP Series Installationsanleitung

Travis Industries

Travis Industries Avalon 900 PS Bedienungsanleitung

Flame

Flame FP-45 Bedienungsanleitung

Astra

Astra P-7 Bedienungsanleitung

Heatilator

Heatilator ECO-ADV-PS35 Bedienungsanleitung

Cadel

Cadel aquos 24 h2O Bedienungsanleitung

vicenza

vicenza V4.5 Bedienungsanleitung

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Technisches Handbuch

Quadra-Fire

Quadra-Fire 1000 Gold Betriebsanleitung

Ferroli

Ferroli GEMMA Bedienungsanleitung

pleasant hearth

pleasant hearth PH35PS Series Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200M-MBK Bedienungsanleitung

England's Stove Works

England's Stove Works 25-EP Bedienungsanleitung

Avalon

Avalon Astoria Bedienungsanleitung

Spartherm

Spartherm Mellino Kurzanleitung