Epic EL 2980 Bedienungsanleitung

USER'S MANUAL

Serial

Number

Decal

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

Model No. EPEL69908.0

Serial No.

Write the serial number in the

space above for reference.

QUESTIONS?

As a manufacturer, we are commit-

ted to providing complete customer

satisfaction. If you have questions,

or if parts are damaged or missing,

PLEASE DO NOT CONTACT THE

STORE; please contact Customer

Care.

IMPORTANT: You must note the

product model number and serial

number (see the drawing above)

before contacting us:

CALL TOLL-FREE:

1-866-997-6999

Mon.–Fri. 6 a.m.–6 p.m. MT

Sat. 8 a.m.–4 p.m. MT

ON THE WEB:

www.iconservice.com

TABLE OF CONTENTS

WARNINGDECALPLACEMENT..............................................................2

IMPORTANTPRECAUTIONS ................................................................3

BEFOREYOUBEGIN ......................................................................4

ASSEMBLY...............................................................................5

HOWTOUSETHEELLIPTICALEXERCISER ..................................................12

MAINTENANCEANDTROUBLESHOOTING ...................................................22

EXERCISEGUIDELINES ...................................................................23

PARTLIST ..............................................................................24

EXPLODEDDRAWING ....................................................................25

ORDERINGREPLACEMENTPARTS ..................................................BackCover

LIMITEDWARRANTY ..............................................................BackCover

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the warn-

ing decal(s). If a decal is missing or illegible,

call the telephone number on the front cover

of this manual and request a free replace-

ment decal. Apply the decal in the location

shown. Note: The decal(s) may not be shown

at actual size.

WARNING: To reduce the risk of serious injury, read all important precautions and in-

structions in this manual and all warnings on your elliptical exerciser before using your elliptical ex-

erciser. ICON assumes no responsibility for personal injury or property damage sustained by or

through the use of this product.

IMPORTANT PRECAUTIONS

1. Before beginning any exercise program, con-

sult your physician. This is especially impor-

tant for persons over the age of 35 or per-

sons with pre-existing health problems.

2. It is the responsibility of the owner to ensure

that all users of the elliptical exerciser are

adequately informed of all precautions.

3. The elliptical exerciser is intended for

home use only. Do not use the elliptical exer-

ciser in a commercial, rental, or institutional

setting.

4. Keep the elliptical exerciser indoors, away

from moisture and dust. Place the elliptical

exerciser on a level surface, with a mat be-

neath it to protect the floor or carpet. Make

sure that there is enough clearance around

the elliptical exerciser to mount, dismount,

and use it.

5. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

6. Keep children under age 12 and pets away

from the elliptical exerciser at all times.

7. The elliptical exerciser should not be used

by persons weighing more than 350 lbs.

(159 kg).

8. Wear appropriate exercise clothes while

using the elliptical exerciser. Always wear

athletic shoes for foot protection while exer-

cising.

9. Hold the handgrip pulse sensors or the han-

dlebars when mounting, dismounting, or

using the elliptical exerciser.

10. The pulse sensor is not a medical device.

Various factors may affect the accuracy of

heart rate readings. The pulse sensor is in-

tended only as an exercise aid in determin-

ing heart rate trends in general.

11. Keep your back straight while using the ellip-

tical exerciser; do not arch your back.

12. If you feel pain or dizziness while exercising,

stop immediately and cool down.

13. When you stop exercising, allow the pedals

to slowly come to a stop.

14. Use the elliptical exercise only as described

in this manual.

Congratulations for selecting the new EPICTMEL 2980

elliptical exerciser. The EL 2980 provides a wide array

of features designed to make your workouts at home

more effective and enjoyable.

For your benefit, read this manual carefully before

you use the elliptical exerciser. If you have ques-

tions after reading this manual, please see the front

cover of this manual. To help us assist you, note the

product model number and serial number before con-

tacting us. The model number and the location of the

serial number decal are shown on the front cover of

this manual.

To avoid a registration fee for any service needed

under warranty, you must register the elliptical ex-

erciser at www.iconservice.com/registration.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Handlebar

Console

Integrated Universal

Dock for iPod

Leveling Foot

Handgrip Pulse Sensor

Water Bottle Holder*

*Water bottle is not included

Wheel

Pedal

Handle

BEFORE YOU BEGIN

M8 Locknut

(72)–4

M4 x 19mm

Screw (57)–2

M10 Split

Washer (85)–6

M10 Washer

(67)–6

M8 Small

Washer (18)–4

M8 Washer

(69)–4

M8 x 55mm Bolt

Set (82)–2

M10 x 123mm Button Bolt (38)–2

M8 x 38mm Button

Bolt (58)–4

Wave Washer

(78)–4

M10 Locknut

(70)–2

M4 x 16mm

Screw (47)–4

Thrust Washer

(66)–4

M10 x 13mm Button

Screw (54)–6

M10 x 65mm Bolt

Set (80)–2

M8 x 19mm Button

Screw (56)–4

M10 x 25mm Patch

Screw (48)–6

ASSEMBLY

To hire an authorized service technician to assemble the elliptical exerciser, call 1-800-445-2480.

Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the

packing materials. Do not dispose of the packing materials until assembly is completed.

In addition to the included tool(s), assembly requires a Phillips screwdriver , an

adjustable wrench , and a rubber mallet .

As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parenthe-

ses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The

number following the parentheses is the quantity needed for assembly. Note: Some small parts may have been

preassembled. If a part is not in the hardware kit, check to see if it has been preassembled.

Attach the Stabilizer (8) to the Frame (1) with

two M10 x 123mm Button Bolts (38) and two

M10 Locknuts (70) (only one is shown).

Tighten two Leveling Feet (36) into the under-

side of the Stabilizer (8).

2. Have another person hold the Upright (2) near

the Frame (1) as shown.

See the inset drawing. Locate the wire tie in

the Upright (2). Tie the lower end of the wire tie

to the Wire Harness (77). Next, pull the upper

end of the wire tie upward out of the top of the

Upright. Then, untie and discard the wire tie.

Tip: Use an elastic band or a piece of tape to

prevent the end of the Wire Harness from

falling into the Upright.

Tip: Avoid pinching the wires. Attach the

Upright (2) to the Frame (1) with four M10 x

25mm Patch Screws (48) and four M10 Split

Washers (85).

388

To make assembly easier, read the

information on page 5 before you begin

assembling the elliptical exerciser.

Avoid pinching

the wires

Wire Tie

3. Attach the Track Frame (4) to the Frame (1) with

two M10 x 25mm Patch Screws (48) and two

M10 Split Washers (85). Tip: Finger tighten a

Patch Screw into the lower hole first, and

then finger tighten a Patch Screw into the

upper hole. Then, tighten both Patch Screws.

Tip: This step may be easier if you raise the

Frame (1) a few inches in the location shown

by the arrow at the right while you attach the

Track Frame (4).

See the inset drawing. Tighten two Leveling

Feet (36) into the underside of the Track Frame

(4).

4. Apply a small amount of the included grease to

the sides of two Wave Washers (78) and to two

Thrust Washers (66).

Slide a Weld Spacer (68) onto the left Crank

Arm (37). Next, identify the Left Track Arm (12),

which is marked with a “Left” sticker.

Orient the Left Track Arm (12) as shown, and

slide it onto the left Crank Arm (37). Then, slide

a Wave Washer (78) on the end of the left Crank

Arm.

Slide an M8 Small Washer (18) and an Axle Cap

(41) onto an M8 x 19mm Button Screw (56).

Next, slide a Thrust Washer (66) onto the shoul-

der of the Axle Cap. Then, tighten the Button

Screw into the end of the left Crank Arm (37).

Make sure that the Thrust Washer remains

on the shoulder of the Axle Cap, and that the

Wave Washer (78) remains on the end of the

left Crank Arm.

Repeat this step to attach the Right Track

Arm (11).

Grease

5. Identify the Left Pedal Leg (14), which is marked

with a “Left” sticker.

Attach a Pedal (21) to the Left Pedal Leg (14)

with three M10 x 13mm Button Screws (54) and

three M10 Washers (67). Make sure that the

Button Screws are in the indicated holes.

The other holes in the Left Pedal Leg are not

used.

Attach the other Pedal (not shown) to the

Right Pedal Leg (not shown) in the same

way.

54 54

6. Apply a thin film of grease to the barrel of an

M10 x 65mm Bolt Set (80).

Fit the bracket on the Left Pedal Leg (14) onto

the bracket on the Left Track Arm (12).

Attach the Left Pedal Leg (14) to the Left Track

Arm (12) with the M10 x 65mm Bolt Set (80).

Attach the Right Pedal Leg (not shown) to

the Right Track Arm (not shown) in the same

way.

Grease

7. Identify the Left Handlebar (19), which is marked

with a “Left” sticker.

Insert the Left Handlebar (19) into one of the

Handlebar Legs (17). Next, turn the Left

Handlebar and the Handlebar Leg so that the

wide side of the pivot tube on the Left

Handlebar is above the hexagonal holes in

the Handlebar Leg.

Attach the Left Handlebar (19) with two M8 x

38mm Button Bolts (58) and two M8 Locknuts

(72). Make sure that the Locknuts are inside

the hexagonal holes. Do not tighten the

Button Bolts yet.

Assemble the Right Handlebar (20) and the

other Handlebar Leg (17) in the same way.

8. Apply a small amount of grease to the sides of

two Wave Washers (78) and to two Thrust

Washers (66).

Slide the Left Handlebar (19), which is marked

with a “Left” sticker, onto the Handlebar Axle

(16) as shown. Next, slide a Wave Washer (78)

onto the end of the Handlebar Axle.

Slide an M8 Small Washer (18) and an Axle Cap

(41) onto an M8 x 19mm Button Screw (56).

Next, slide a Thrust Washer (66) onto the shoul-

der of the Axle Cap. Then, tighten the Button

Screw a few turns into the end of the Handlebar

Axle (16). Make sure that the Thrust Washer

remains on the shoulder of the Axle Cap, and

that the Wave Washer (78) remains on the

end of the Handlebar Axle.

Assemble the Right Handlebar (20) in the

same way. Then, tighten both M8 x 19mm

Button Screws (56) at the same time.

19 20

58 58

17 17

Hexagonal

Holes

Wide side of

pivot tube

Grease

9. Apply a film of grease to the barrel of an M8 x

55mm Bolt Set (82) and to a 7mm Spacer (55).

Slide an M8 Washer (69) and the Spacer onto

the barrel of the Bolt Set.

While another person holds the front end of the

Left Pedal Leg (14) inside the bracket on the left

Handlebar Leg (17), insert the barrel of the M8 x

55mm Bolt Set (82) through both parts.

Next, slide a 7mm Spacer (55) and an M8

Washer (69) onto the end of the barrel of the M8

x 55mm Bolt Set (82). Then, turn the screw of

the Bolt Set a few turns into the barrel. Do not

overtighten the Bolt Set; the left Handlebar

Leg must pivot freely.

Attach the right Handlebar Leg (not shown)

to the Right Pedal Leg (not shown) in the

same way.

See step 7. Tighten the four M8 x 38mm Button

Bolts (58).

10. While another person holds the Console (74)

near the Upright (2), connect the Pulse Jumper

Wire (76) to the console pulse wire. Then, con-

nect the Wire Harness (77) to the console wire

harness. Insert the excess wire into the Upright.

Tip: Avoid pinching the wires. Set the

Console (74) on the Upright (2). Attach the

Console with four M4 x 16mm Screws (47).

17 82

55 69

Pulse Wire

Grease

Avoid pinching

the wires

Console Wire

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Epic Ellipsentrainer Handbücher

Epic

Epic 1000 Ex Elliptical Bedienungsanleitung

Epic

Epic 1200 Pro Elliptical Bedienungsanleitung

Epic

Epic 1200 Pro Elliptical Bedienungsanleitung

Epic

Epic 790 Hr Elliptical Bedienungsanleitung

Epic

Epic EL 2790 Bedienungsanleitung

Epic

Epic 790 Hr Elliptical Bedienungsanleitung

Epic

Epic A30E EPEL19912.0 Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

Precor

Precor Resolute RSL 620 Bedienungsanleitung

NordicTrack

NordicTrack E 9.2 Elliptical Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung