EPOX P55-VP 2 Bedienungsanleitung

Introduction1-1

Chapter 1

Introduction

The P55-VP 2mainboard is a high performance system hardware based

on Intel Pentium processor and is equipped with three PCI slots, four

standardISAslots,SuperMulti-I/O controlleranddual portPCI-IDE

connectorsforthefutureexpansion.Thehardwaredimensionis220mmx

230mmwithafour-layer-designtechnology.

Specification

VIAApolloVPXPCIsetchipset.

Intel Pentium Processor, AMD K5/K6 & Cyrix M1 operating at75 ~ 200

MHz andP55C with321 ZIF socket 7 and scalability to accept faster

Processors in the future.

Supports up to 192 MegaBytes of DRAM (a minimum of 8 MB) on board

(72-pinSIMMx4&168-pinDIMMx1). BIOSwillautometicallydetectand

configure FP/EDO and Synchronous DRAM (Refer to Chapter 2-3 System

MemoryConfiguration).

Supports Onboard Pipelined Burst (synchronous) L2WriteBack/Through

Cache.Thecachememorycombinationcanbe256KB/512KB(32KB*32,

64KB*32SRAM,respectively).

Supports four 16 bit ISA slots and three 32 bit PCI slots and provides two

independent high performance PCI IDE interfaces capable of supporting

PIOMode3/4andUltra-DMA33devices.TheP55-VP2supportsthreePCI

Bus Masters and a jumperless PCI INT# control scheme which reduces

configurationconfusion whenplugging in PCI I/O controller card(s).

SupportsATAPI(e.g.CD-ROM)devicesonbothIDEinterfaces.

Supports1floppyport,1parallelport(EPP,ECPport), 2 serial ports (16550

FastUARTcompatible)and1USB Connector.

Supports a PS/2 style mouse and standard AT style keyboard connectors.

SupportsAwardPlug & Play BIOS . TheBIOS is stored in Flash EPROM

form. It provides better upgradeability for the system.

Supports CPU Hardware sleep and SMM (System Management Mode).

P55-VP2utilizes Lithiumbatterywhichprovidesenvironmentalprotection

and longer battery life.

1-2 P55-VP 2

P55-VP 2 Layout

BIOS

PCI#1

BIOS

PRINTER

W83877F

82C585

VIA

K/B

CONN.

Power Conn.

DIMM1

SIMM1

SIMM2

SIMM3

SIMM4

COM2COM1

J2 1

3 1 JP1

FDD CONN.

PCI#3

PCI#2

64K*32 64K*32

82C587

VIA

82C587

VIA

Figure1-1

HD-LED+

G-LED+ TB-LED+

SPEAKER

KEYLOCK J5

5 1 3 1 3 1

JP8 JP7

JP3 1

TAG SRAM

\Bank 4,5 / \ Bank 2,3 /

Bank 0,1

Primary IDE

Secondary IDE

SLEEP

RESET

1 2

7 8

JP6

JP2-2

JP2-1

JP2-3

JP2-4

82C586A

JP4 1

Socket 7

Hardware Design 2-1

2-1 Mainboard Layout

TheP55-VP2isdesignedwithVIAApolloVPXPCIset chipset which isdevel-

oped by VIA Corporation to fully support Pentium Processor PCI/ISA system. The

VIAApolloVPXPCIsetchipsetcanincreaseintegrationandimproveperformance

designs.The chipset provides an integrated IDEcontroller with two high perfor-

manceIDEinterfacesforuptofourIDEdevices(harddevices,CD-ROM device,etc).

TheWinbondW83877FSuperI/Ocontroller providesthestandardPCI/Ofunction:

floppyinterface,two16ByteFIFOserialportsandEPP/ECPcapableparallelport.

The P55-VP 2 layout is shown in the previous page for user's reference. Care must

betakenwheninsertingmemorymodules,insertingCPUorevenpluggingPCIcard

into associated slots to avoid damaging any circuits or sockets on board. A cooling

fanisstronglyrecommendedwheninstallingP54C/P54CTB/P55C/K5/K6/6x86/6x86L/

M2 processor due to possible overheat.

TheP55-VP2supportsaminimumof4MBandamaximumof192MBofSystem

MemorywhileL2Cachecanbe256KB/512KBsynchronousSRAMOnboardto

increasesystemperformance.(RefertoPage2-6CacheMemoryConfigurationfor

thedetails.)

TheP55-VP 2supports standard Fast Page, EDO(ExtendedData Out or Hyper

Page Mode) or synchronous DRAM.The P55-VP 2provides four 72-pin SIMM

andone168-pin DIMM sites for memory expansion.Thesockets support 1M x

32(4MB),2Mx32(8MB),4Mx32(16MB),and8Mx32(32MB)single-sidedordouble-

sidedmemory modules.The memorytimingrequires70ns Fastpagedevicesor60

nsEDODRAM.(DRAMModulesmaybeparity[x36]ornon-parity[x32].

TheP55-VP2supportstwoOnboardPCIIDEconnectors,andautomaticallydetects

IDEharddisktypebyBIOSutilityautomatic.

The P55-VP 2supports Award Plug & PlayBIOSfor the ISA and PCI cards. The

BIOScanbelocated inFlashEPROMwhichcanreplace BIOS codeeasilyifneces-

sary.

Chapter 2

Hardware design

2-2 P55-VP 2

2-2ConnectorsandJumpers

This section describes all connectors and jumpers equipped in the mainboard. Please

refer to Figure 1-1for location of each connector and jumper.

1.Power LED(+)

2.N/C

3.GND

4.Keylock

5.GND

1.Speaker

2.N/C

3.GND

4.GND

J5 1

Power Saving LED indicator - LED ON when system is

in any Saving mode.

Reset Switch - Closed to restart system.

Speaker - connect to the system's speaker for beeping.

KeyLock-Keyboardlockswitch&PowerLEDconnector.

Sleep/Resume switch: Closedtoentersleepmode.

Akeystrobeormousemovement(mousedriverexists).Will

instantly "wake up" the system.

TurboLEDindicator-LEDONwhenhigherspeedisselected.

IDELEDindicator-LEDONwhenOnboardPCIIDE

Harddisksactivate.

+# There is no deturbo function so that the turbo LED is always ON.

J3 The Power Supply (+12V) of the CPU Cooling FAN

1.GND

2.+12V

3.GND

Hardware Design 2-3

J1 PS/2 MOUSE CONNECTOR

1.RED wire

2.BLUE wire

3.GREEN wire

4.NC

5.YELLOW wire

J2 IrDA/ASKIRCONNECTOR

1.VCC

2.NC

3.IRRX

4.GND

5.IRTX

JP1 EPROMBIOSSelection

1-2:5VFlashEPROM.(SST,Winbond).

2-3:12VFlashEPROM(Intel).

JP3 CPUVcorevoltageselection

1-2:2.9VForAMDK6-PR166/200

2-3:2.8VForPentiumMMXProcessor&Cyrix6x86L

Open: 3.2V (Reserved)

JP4 CPUTypeSelection

1-2:Auto(forIntelPentiumMMXProcessor,AMDK5/

K6andCyrix6x86/6x86L/M2)

2-3:Manual(forIntelPentiumProcessor)

JP6 DIMM Working Voltage Selection

1-2, 3-4 : 5V

5-6, 7-8 : 3.3V (Default)

(Refer to 2-3 : Memory Configuration for the detail)

1 2

7 8

2-4 P55-VP 2

6x86/L-PR120+

CPU TYPE JP2-1 JP2-2 JP2-3 JP2-4 JP7 JP8

6x86/L-PR150+

6x86/L-PR166+ ON

OFF

IBM/ Cyrix 6x86(L)/6x86MXInstallation

*CPUOo.isCPUoperationat75,90,100MHz,andetc.

ON ON

OFF

6x86/L-PR133+

6x86/L-PR200+

2-3 1-2

OFF OFF

OFF

OFF OFF

OFF

Note 1

Note 2

Note1:IBM/CyrixPR200withsynchornousPCI

Note2:IBM/CyrixPR200withasynchornousPCIforPCI2.0

spec. Bus Master Device

* Clock is System Clock.

Intel Pentium Processor / Pentium MMX Processor

/AMD K5 /K6 Installation

2-3 2-3

1-2 2-3

2-3 1-2

1-2 1-2

ON OFF ON

OFF

ON ON

OFF

OFF ON

OFF

OFF ON

Clock/CPU Op. JP2-1 JP2-2 JP2-3 JP2-4 JP7 JP8

66/200 MHz

JP8 JP7

3 1 3 1

60/90 MHz

66/100 MHz

66/133 MHz

60/150 MHz

60/180 MHz

66/166 MHz

JP2 1 2 3 4

50/75 MHz

60/120 MHz

OFF

6x86MX-PR200

6x86MX-PR166 ON

OFF

ON ON

OFF

OFF6x86MX-PR166

6x86MX-PR200

2-3 2-3

OFF OFF

OFF

OFF OFF

OFF

Note 1

Note 2

66MHz x 2

75MHz x 2

60MHz x 2.5

66MHz x 2.5

Hardware Design 2-5

*6x86-PR120+=50MHzx2/100MHz,6x86-PR133+=55MHzx2/110MHz

*6x86-PR150+=60MHzx2/120MHz,6x86-PR166+=66MHzx2/133MHz

*6x86-PR200+=75MHzx2/150MHz

2-3SystemMemoryConfiguration

The P55-VP 2 supports different type of settings for the system memory. The

followingfiguresand table providesallpossiblememorycombinations. (Pleaserefer

toAppendixC:MemoryConfigurationTableforthedetails).

JP3 CPUVcorevoltageselection

1-2:2.9VForAMDK6-PR166/200

2-3:2.8VForPentiumMMXProcessor&Cyrix6x86L

Open:3.2V(Reserved)

JP4 CPUTypeSelection

1-2:Auto(forIntelPentiumMMXProcessor,AMDK5/K6

andCyrix6x86/6x86L/M2)

2-3:Manual(for IntelPentiumProcessor)

DIMM

SIMM4

SIMM2

SIMM3 BANK 4,5 5V FP / EDO DRAM

BANK 2,3 5V FP / EDO DRAM

3V Synchronous DRAM

or 3V FP / EDO DRAM

BANK 0,1

NOTE :1.P55-VP2supports both FastPageDRAMandEDO DRAM SIMMs,but

they cannot be used in the same memory bank.

2.TheKEYZOOMoftheDIMMsocketis3.3V/Unbuffered.

SIMM1

LEFT KEY ZONE CENTER KEY ZONE

DRAM chip

2-6 P55-VP 2

2-4CacheMemoryConfiguration

The second level (L2) of cache is installed in the mainboard to increase the system

performance. The P55-VP 2 supports different type of combinations for the cache

installation.Pleaserefer to thefollowingconfigurationsforthe details.

DATA SRAM

64K*32

U19 U20

SYN.CACHE On Board

256KB 32K*32 x 2

512KB 64K*32 x 2

Size (U19,U20)

TAG SRAM

U21

The P55-VP 2supports168-pinDIMMmoduletoextend system memory size. You

caninstall(3.3V /Unbuffered)FastPage,EDO orSynchronousDRAM.Besides, to

support5VFP and EDO DRAM with DIMMsocket,TheP55-VP 2 provides JP6 to

allow user using 3.3V/Unbuffered DIMM module with 5V FP and EDO DRAM

chips. The setting of the JP6 is shown as follows:

When you have a DIMM module to plug into a 168-pin dual readout connnector,

youmustmakesurethattheKEYZOOMoftheDIMMmoduleis3.3V/Unbuffered

and supports Intel Pentium Processor System.

JP6 DIMM Working Voltage Selection

1-2, 3-4 : 5V

5-6, 7-8 : 3.3V (Default)

1 2

7 8

64K*32

Hardware Design 2-7

2-5IntegratedPCIBridge

The P55-VP 2 utilizes PCIsetchipsettosupportIntelPentium ProcessorPCI/ISA

system.TheVIAApolloVPXPCIsetchipsetconsistsofthe82C585VPsystem

controller(TSC),two82C587VPDataPath(TDP)devices,andone82C586APCIISA/

IDEAcceleratorbridge chip. Itprovidesaninterfacewhich translates CPUcycleinto

PCIbuscycle,andPCIburstread/writecapability.Inaddition,itprovideshigh

performancePCIarbitortosupportfourPCIMasters,RotatingPriorityMechanism,

andHiddenArbitrationSchemeMinimizesArbitrationOverhead.

TherearefourinterruptsineachPCIslot:INTA#,INTB#,INTC#,andINTD#.Since

the P55-VP 2adapts the PCI auto-configuration with the system BIOS Setup utility.

Whenthesystemis turned on after adding a PCI add-incard,theBIOS automatically

configure interrupts, DMA channels, I/O space, and other paramaters. You do not

have to configure jumpers or worry about potential resource conflicts. Because PCI

cards use the same interrupt resource as ISA cards, you must specify the interrupt

used by ISA add-in cards in the BIOS Setup utility.

However, if a "Legacy card" (such as plugging a paddle card and cable into an ISA

slot)ispluggedinthesystem,modificationinthe ROMSETUPUTILITYbecomes

necessary.Firstofall,youmustenterPCICONFIGURATIONSETUPutilityfrom

theROMSETUPUTILITYmainmenutoset"ISA"forthe"PCIIDEIRQMAPTO

Secondly,youmustentertheCHIPSETFEATURESSETUPUTILITYfromtheROM

SETUPUTILITYmainmenuandset"Disable"forthe"OnboardPrimaryPCIIDE

andtheOnboardSecondaryPCIIDE.WhenyouplugPCI/ISAIDEcardsintothe

system,Youshouldselect"Disabled"fortheOnboardPrimaryandSecondaryPCI

IDEfromtheCHIPSETFEATURESSETUPUTILITYtoo.

You can set the system interrupt request (IRQ) on some "Legacy cards" which have

on paddle card and cable. (refer to user's manual of the card) to a proper system IRQ

level (In general, card's Primary is assigned to INTA and Secondary is assigned to

INTB). If the card is plugged into slot 1(marked PCI#1), you cannot use second slot

(markedPCI#2) becausetheSecondaryINTsignaltakesINTBfromtheslot(refer to

Page3-12forcircuitdiagram).Theuserthenentersthe PCICONFIGURATION

SETUPutilityfromthe ROMSETUPUTILITYmainmenuandset"PCI-Slot1"for

the"PCI IDE IRQMAPTO(Thisdependsonthe slot#wheretheLegacy cardis

plugged).

AWARD BIOS 3-1

CHAPTER 3

AWARD BIOS SETUP

Award'sROMBIOSprovidesabuilt-insetupprogramwhichallowsusertomodifythe

basicsystemconfigurationandhardwareparameters.Themodifieddatawillbestored

inabattery-backedCMOSRAMsodatawillberetainedevenwhenthepoweristurned

off.Ingeneral,theinformationsavedintheCMOSRAMstaysunchangedunlessthere

isaconfigurationchangeinthesystem,suchasaharddrivereplacementoranewdevice

installation.

If this does happen you will need to reconfigure your configuration parameter.

To Enter Setup Propgram

Poweronthecomputerandpress<Del>keyimmediately.ThiswillbringyouintoBIOS

CMOSSETUPUTILITY.

ROMPCI/ISABIOS(2A5LDPA9)

CMOSSETUPUTILITY

AWARDSOFTWARE,INC.

STANDARD CMOS SETUP SUPERVISOR PASSWORD

BIOS FEATURES SETUP USER PASSWORD

CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION

POWER MANAGEMENT SETUP HDD LOW LEVEL FORMAT

PNP/PCI CONFIGURATION SAVE & EXIT SETUP

INTEGRATED PERIPHERALS EXIT WITHOUT SAVING

LOAD SETUP DEFAULTS

ESC : QUIT : SELECT ITEM

F10 : Save & Exit Setup (Shift)F2 : Change Color

Time, Date, Hard Disk Type...

Figure 3-1 CMOS SETUP UTILITY

Themenudisplaysallmajorselectionitems. Select the item you need to reconfigure.

The selection is made by moving cursor (press any direction key ) to the item and

press the 'Enter' key. An on-line help message is displayed at the bottom of the

screen as the cursor is moving to various items which provides a better understand-

ingof each function. Whena selection is made,the menu of selecteditem will appear

so the user can modify the associated configuration parameters.

Inhaltsverzeichnis

Andere EPOX Hauptplatine Handbücher

EPOX

EPOX EP-5NVA+SLI Bedienungsanleitung

EPOX

EPOX 3WXM4 Bedienungsanleitung

EPOX

EPOX MVP4G Bedienungsanleitung

EPOX

EPOX P55TV2 Bedienungsanleitung

EPOX

EPOX EP-3C1A Bedienungsanleitung

EPOX

EPOX F62 Bedienungsanleitung

EPOX

EPOX 3VCA Bedienungsanleitung

EPOX

EPOX EP-6ZXM Bedienungsanleitung

EPOX

EPOX EP-V370Y Bedienungsanleitung

EPOX

EPOX LX370Y Bedienungsanleitung

EPOX

EPOX nForce2 Ultra 400 Bedienungsanleitung

EPOX

EPOX EP-5ATXA-M Bedienungsanleitung

EPOX

EPOX KP6-LS Bedienungsanleitung

EPOX

EPOX P2-133A Bedienungsanleitung

EPOX

EPOX EP-BX6 Bedienungsanleitung

EPOX

EPOX MU-4PEA800 Bedienungsanleitung

EPOX

EPOX nVIDIA nForce3 250Gb Bedienungsanleitung

EPOX

EPOX 3WXA Bedienungsanleitung

EPOX

EPOX 6XBA2 Bedienungsanleitung

EPOX

EPOX EP-3S1M Bedienungsanleitung

EPOX

EPOX EP-MVP3G-M Bedienungsanleitung

EPOX

EPOX BX5 Bedienungsanleitung

EPOX

EPOX EP-8HDA5J Bedienungsanleitung

EPOX

EPOX 6VBA Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

Epson

Epson S5U13700P00C000 Bedienungsanleitung