EPOX BX5 Bedienungsanleitung

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 2.1

August 16, 1999

BX5

A PA P

A Pentiumentium

entiumentium

entium®®

®®

®II/III/CelerII/III/Celer

II/III/CelerII/III/Celer

II/III/Celeronon

onon

Slot1 Processor based AGPSlot1 Processor based AGP

Slot1 Processor based AGP

motherboard (100/66MHz)

FeaturesBX5

Page 1

FEATURES

BX5 Features:

•BX5 is based on the Pentium®II or Pentium®III Processor operating

at 233 ~ 400MHz (66MHz) or 300 ~ 550MHz (100MHz) on Slot 1.

There are no jumper setting for CPU Speed Setup but detected automati-

cally through the BIOS.

•Designed with Intel’s 82443 BX AGPset.

•Supports up to 1 GB of SDRAM (minimum of 8 MB) on board, You can

use 168-pin DIMM x 4. It will automatically detect Extended Data Output

(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM)

at 66MHz or 100MHz (please see Section 3-2).

•BX5 will not support Error Checking and Correcting (ECC) when using

paritys DRAM memory modules.

•Supports (2) 16 bit ISA slots, (5) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The BX5 supports (5) PCI

Bus Master slots and a jumperless PCI INT# control scheme which reduces

configuration confusion when plugging in PCI card(s).

•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

•Designed with Winbond W83977TF/EF Multi I/O: (1) floppy port, (1)

parallel port (EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported.

•Includes a PS/2 mouse connector.

•Allows use of a PS/2 keyboard.

•Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com

please visit our Technical Support section for the latest updates).

FeaturesBX5

Page 2

•BX5 utilizes a Lithium battery which provides environmental protec

tion and longer battery life.

•Supports the Universal Serial Bus (USB) connector. The onboard PIIX4E

chip provides the means for connecting PC peripherals such as; keyboards,

joysticks, telephones, and modems.

•Built-in ATX 20-pin power supply connector.

•Software power-down when using Windows®95/98.

•Supports ring-in feature (remote power-on through external modem,

allow system to be turned on remotely).

•Resume by Alarm - Allow your system to turn on at a preselected time.

•Power Loss Recovery - In the event of a power outage your system will

automatically turn itself back on without user intervention.

•Supports CPU Hardware sleep and SMM (System Management Mode).

•Supports Desktop Management Interface (DMI) facilitating the manage-

ment of desktop computers, hardware and software components and

peripherals, whether they are stand-alone systems or linked into networks.

(optional)

•Supports Hot key, Any key or password Keyboard power ON function

(KBPO).

•Supports USDM software to allow the status monitoring of various aspects

of the system when using Windows®95/98 or Windows®NT 4.0.

•Supports the CPU, PWR and Chassis fan Auto stop in the sleep mode.

•Supports the System Power LED (PANEL) blinks in the sleep mode.

•Built-in WOL (Wake On LAN) Connector.

InstallationBX5

Page 3

Figure 1

BX5 Detailed Layout

Installation

BX5

Page 4

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure Jumpers

System memory Configuration

Device Connectors

Configure Settings

The following will describe all of the setting that you are required to set before

moving on to step 2.

ROM PCI/ISA BIOS(2A69KPAG)

SENSOR & CPU SPEED SETTING

AWARD SOFTWARE, INC.

Auto Detect DIMM/PCI Clk : Enabled

Spread Spectrum Modulated : Disabled

CPU Host/PCI Clk : Default

CPU/AGP Clk Ratio : Default

CPU Int Clk Ratio : x3

CPU Clk Frequency : 300(100x3) MHz

CPU:AGP (Clk:Clk) : 3:2 (100:66)

CPU Vcore Voltage : +0.10V

CPU Vcore Voltage : 2.10V

** BIOS Writer Utility **

Checksum Error Detect : Both

Source : A:

Target : Mater

Go : Enter

CPU Warning Temperature : Disabled

Extended JP2 Temperature : 0OC/32OC

Current CPU Temperature : 0OC/32OC

Current System Temperature : 0OC/32OC

Current POWER FAN Speed :4900 RPM

Current CPU FAN Speed : 4900 RPM

Current CHASSIS FAN Speed : 4900 RPM

Vcore : 2.10V Vtt(V) : 1.55V

Vio(V) : 3.47V +5V :5.02V

+12V : 12.40V -12V : -11.95V

-5V : -5.50V VBAT (V) : 3.44V

5VSB (V) : 5.08V

Shutdown Temperature : 60OC/140OC

Esc:Quit : Select Item

F1 : Help PU/PD/+/-: Modify

F5 : Old Values (Shift) F2 : Color

F7 : Load Setup Defaults

éé

êê

èè

çç

InstallationBX5

Page 5

Note:Based on the implementation of the Intel 440BX AGPset, the BX5

is able to provide multiple front side bus (FSB) frequencies for Slot 1

processors and memory operations. The motherboard's FSB is easily se-

lected by BIOS Setup listed above to match the FSB required by your

processor. When using the 100MHz FSB (or higher) you must use

PC100 (or better) compliant SDRAM.

Memory is an important component of any motherboard. When

selecting memory for use on the 2theMax brand motherboard we

recommend use only the finest quality modules. 2theMax would like to

stress that using non-compliant PC100 SDRAM modules with a

100MHz (or higher) FSB severely compromises the integrity of the

system.

epyTUPCkcolClanretxEoitaR

epyT1tolS

IImuitneP

IIImuitneP

noreleC

draCtrevnoC+073S

001

0.2

5.2

0.3

5.3

0.4

5.4

0.5

5.5

0.6

5.6

0.7

5.7

0.8

JP1=1-2-Normal(Default)=2-3- ClearCMOS(momentarily)

JP1Chassis(Case)intruder detect

JP2The3thThermalConnector

JP4 Keyboard Power-ON function

JP4 = 1-2 - Enabled

= 2-3 - Normal (Default)

Installation

BX5

Page 6

J7 ReservedforNIC(NetworkInterface Card)to

WaketheSystem.

WOL

(Wake OnLAN)

Connector

J1 SB-LINK Connector

Reserved for Creative SB-LINK (Sound

Blaster LINK ) with the Sound Blaster

AWE64D PCI Sound Card to compatible

JP1 = 1-2 - Normal (Default)

= 2-3 - Clear CMOS (momentarily)

JP5 CMOS Clear

JP4 Keyboard Power-ON function

JP4 = 1-2 - Enabled

= 2-3 - Normal (Default)

InstallationBX5

Page 7

yromeMlatoT 1MMID )1/0knaB( 2MMID )3/2knaB( 3MMID )5/4knaB( 4MMID )7/6knaB(

BM652= mumixaM

*MARDS/ODE ,BM23,BM61,BM8 ,BM821,BM46 1xBM652

enoNenoNenoN

BM215=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

enoNenoN

BM867=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

enoN

BG1=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

*MARDS/ODE

,BM23,BM61,BM8

,BM821,BM46

1xBM652

* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.

*Using non-compliant memory with higher bus speed (over clocking)

may severely compromise the integrity of the system.

System Memory Configuration

Memory Layout

The BX5 supports (4) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized

DRAM).

•We recommend not mixing SDRAM DIMM and EDO DIMM together.

• EDO DIMM can only be used with the 66MHz FSB.

• We recommend using at least 125MHz (-8ns) SDRAM DIMM at the 100MHz

(or higher) FSB as timing becomes more critical at these higher speeds.

• DIMM SDRAM may be 83MHz (-12ns), 100MHz (-10ns) or 125MHz (-

8ns) bus speed.

Figure 2 and Table 1 show several possible memory configurations using

Figure 2

Table 1

DIMM 1 (M1)

DIMM 2 (M2)

DIMM 3 (M3)

DIMM 4 (M4)

Bank 0/1

Bank 2/3

Bank 4/5

Bank 6/7

-Synchronous

-SDRAM or EDO

DIMM

InstallationBX5

Page 8

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connec-

tions (figure 10).

Figure 10

PS/2 Mouse

PS/2 Keyboard

ParallelPort

COM1USB COM2

J2,J3: Chassis Panel Connector

• Power LED, Speaker, Reset, Turbo LED, HDD LED, IR Conn., Sleep/

Power_ON

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J6: Power Supply Fan Monitoring

• A plug-in for the Power supply so that BIOS can monitor the RPM’s

J8: Chassis Fan Power

• A plug-in for the chassis Fan Power

IDE1: Primary IDE Connector

IDE2: Secondary IDE Connector

FDD1: Floppy Controller Connector

PW2: ATX Power Connector

• 20-pin power connector

Installation

BX5

Page 9

Device Connectors(continued)

(This is connected to the power button on the case. Using the Soft-

Off by Pwr-BTTN feature, you can choose either Instant Off (turns

system off immediately), or 4 sec delay (you need to hold the button

down for 4 seconds before the system turns off). When the system is

in 4 sec delay mode, there is a special feature to make the system to

go into suspend mode when the button is pressed momentarily.)

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard disks

is activate

J3 1

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

Power On/Off

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

KeyLock - Keyboard lock switch & Power LED connector

1. Power LED(+) 4. KeyLock

2. N/C 5. GND

3. GND

Inhaltsverzeichnis

Andere EPOX Hauptplatine Handbücher

EPOX

EPOX 61BXA-M Bedienungsanleitung

EPOX

EPOX EP-BX5C Bedienungsanleitung

EPOX

EPOX EP-3VCA Bedienungsanleitung

EPOX

EPOX MVP3G-M Bedienungsanleitung

EPOX

EPOX IP-4PCI2E Series Bedienungsanleitung

EPOX

EPOX EP-3WXM2 Bedienungsanleitung

EPOX

EPOX MVP4M Bedienungsanleitung

EPOX

EPOX 3WXA Bedienungsanleitung

EPOX

EPOX 3WXM4 Bedienungsanleitung

EPOX

EPOX EP-6ZXM Bedienungsanleitung

EPOX

EPOX EP-6VBA Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

EPOX

EPOX SiS 661FX Bedienungsanleitung

EPOX

EPOX EP-4B2AE Bedienungsanleitung

EPOX

EPOX EP-BX3 Bedienungsanleitung

EPOX

EPOX EP-8RDAE Bedienungsanleitung

EPOX

EPOX KP6-LS Bedienungsanleitung

EPOX

EPOX EP-3VCA2 Bedienungsanleitung

EPOX

EPOX LX370Y Bedienungsanleitung

EPOX

EPOX 6VBA Bedienungsanleitung

EPOX

EPOX KP6-LA Bedienungsanleitung

EPOX

EPOX EP-3VHA Bedienungsanleitung

EPOX

EPOX EP-58MVP3C-M Bedienungsanleitung

EPOX

EPOX LX370Y Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung