Equinox Systems EQLED019 Bedienungsanleitung

Order code: EQLED019

Switchblade

User Manual

www.prolight.co.uk Switchblade User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 100~240V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• Never touch the xture during operation as it may be hot.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is not

designed for or suitable for household use. The product

must be installed by a qualied technician in accordance

with local territory regulations. The safety of the installation

is the responsibility of the installer. The xture presents

risks of severe injury or death due to re hazards, electric

shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk Switchblade User Manual 3

Safety advice

This xture falls under Protection Class 1, therefore it has to be connected

to a mains socket with a protective earthing connection.

Risk group 2, RG-2: CAUTION!

Do not stare at exposed LED in operation as it may damage/be harmful to

the eyes. Avoid looking directly into the light source.

CAUTION!

If the lens gets damaged ie. cracks or deep scratches so the output is impaired

then it must be replaced.

CAUTION!

The maximum ambient temperature (Ta) of 40° must not be exceeded.

www.prolight.co.uk Switchblade User Manual 4

8° - Lux (Beam)

FULL ON

160° - Lux (Strobe)

FULL ON

62232

9048

22484

4300

27696

734

222

446

150

15558

2262

5621

1075

6924

183

55.6

111

37.5

6914

1005

2498

477

3077

81.6

24.7

49.6

16.6

3889

565

1405

268

1731

45.6

13.9

27.9

9.3

2489

361

899

172

1107

29.3

8.9

17.8

0m 2m 3m 4m 5m1m

8° 160°

Product overview & technical specications

• 5 x 40W quad-colour LEDs (RGBW)

• Beam angle: 8°

• 15,558 Lux @ 2m (per LED, full on)

• 16kHz refresh rate

• 250 x tri-colour 5050 SMD LEDs (RGB)

• Beam angle: 160°

• 183 Lux @ 2m (full on)

• 500Hz refresh rate

• Individually controllable LEDs (beams)/

zones (strobe)

• DMX channels: 2/15/23 or 48 selectable

• Auto, sound active and master/slave modes

• Pan/tilt auto correction

• 16 bit pan/tilt positioning

• 360° continuous pan and tilt

• 0-100% dimming and variable strobe

• Supplied with quick release omega clamp

• 4 push button menu with 2.5” LCD display

• PowerCON input/output

• 5-Pin XLR input/output

• Fan cooled

Switchblade

Specications Switchblade

Power consumption 365W

Power supply 100~240V, 50/60Hz

Fuse F5A 250V

Dimensions 315 x 538 x 182mm

Weight 11kg

Order code EQLED019

Incorporating a beam and strobe/wash effect, the Switchblade does it all. One side of the sleek bar features

ve pixel mappable beams with an 8° beam angle whilst the other has 250 tri-colour LEDs controllable over ve

zones which strobe/wash to ll venues with blinding effects in any colour. Innite pan and tilt with lightning quick

movements along with razor sharp beams create awesome aerial effects.

Beam optics:

Strobe optics:

www.prolight.co.uk Switchblade User Manual 5

Technical specications

182mm

289mm

428mm

538mm

315mm

93mm

144mm

159mm

www.prolight.co.uk Switchblade User Manual 6

Technical specications

01 - LCD display

02 - Function buttons

03 - 5-Pin DMX input

04 - 5-Pin DMX output

05 - PowerCON input

06 - PowerCON output

07 - Fuse F5A 250V

08 - Power switch

09 - Carry handles

In the box: 1 x xture,

2 x omega clamps,

1 x power cable

& 1 x user manual

05 06 07

01 02

www.prolight.co.uk Switchblade User Manual 7

Installation

Before installing the xture, the supporting structure (ie. truss) must be able to hold a minimum of 10

times the xtures weight without any deformation (eg. 15kg - 150kg point load). The xture must be

secured with a secondary safety attachment when being installed (ie. an appropriate safety cable).

Never stand directly below the xture when mounting, removing, and/or servicing.

Overhead installation requires experience and qualications to calculate working load limits, the

material being used at the installation area and periodic safety inspections of the xture and installation

material. If you do not have the relevant experience and/or qualications please do not attempt the

installation yourself. The installation should be checked annually by a qualied person.

The Equinox Switchblade can be operated in a number of mounting positions as shown in the diagram

above, hanging upside-down from the ceiling or truss, mounting sideways on truss or stood upright on a

at level surface. Always use a safety wire as an extra safety precaution to prevent damage/injury in the

event a clamp fails (see the next page for clamp installation).

Never use the carry handles for secondary attachments.

www.prolight.co.uk Switchblade User Manual 8

Installation

Installation:

1. Fasten each clamp to the omega clamps with a bolt and lock nut through the hole in the

omega clamp.

2. Align and insert the omega clamp quick-lock fasteners with the respective holes on the bottom

of the unit.

3. Tighten both locking fasteners clockwise on each omega clamp ensuring they’re fully secure.

4. Mount the xture onto your truss system via the clamps and tighten to ensure secure.

5. Pull the safety cable through the safety cable holes located on the metal base plate on the

underside of the xture and around the truss.

www.prolight.co.uk Switchblade User Manual 9

Operating instructions

Control Panel Menu:

The LCD control panel situated on the front of the xture allows the user to access the menu system

adjust the xtures settings.

When the unit has been powered on the display will show “Equinox Switchblade”, “Motor Reset...

Please Wait...” whilst the unit performs its motor reset.

The xture will then return to its home screen.

Pressing the “MENU” button once will take the user to the xtures main menu. Using the “UP” and

“DOWN” buttons you can then navigate between the different options in the main menu. Pressing the

“ENTER” button on one of these options allows you to access the sub menu where you can use the

“UP” and “DOWN” buttons to select option/value required. Once the option/value has been selected

press the “ENTER” button once more to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

When exiting the menu the xture will display “5”, “4”, “3”, “2”, “1” before returning to the home screen.

DOWN

ENTER

www.prolight.co.uk Switchblade User Manual 10

DMX

Address xxx

DMX address:

To access the DMX address mode, press the

“MENU” button and use the “UP” and “DOWN”

buttons to show “DMX Address” on the LCD

display. Now press the “ENTER” button and use

the “UP” and “DOWN” buttons to set the required

DMX address. Press the “ENTER” button to

conrm the setting.

Main Menu - Defaults are in grey

DMX channel mode:

To access the DMX channel mode, press the

“MENU” button and use the “UP” and “DOWN”

buttons to show “Channel Mode” on the LCD

display. Now press the “ENTER” button and use

the “UP” and “DOWN” buttons to set the required

DMX channel. Press the “ENTER” button to

conrm the setting.

Show mode:

To access the show modes, press the “MENU”

button and use the “UP” and “DOWN” buttons to

show “Auto Mode” on the LCD display. Press the

“ENTER” button and use the “UP” and “DOWN”

buttons to show “Show Mode”. Now press the

“ENTER” button and use the “UP” and “DOWN”

buttons to set the required show mode.

Press the “ENTER” button to conrm the setting.

Show speed:

To access the show speed setting, press the

“MENU” button and use the “UP” and “DOWN”

buttons to show “Auto Mode” on the LCD display.

Press the “ENTER” button and use the “UP” and

“DOWN” buttons to show “Show Speed”. Now

press the “ENTER” button and use the “UP” and

“DOWN” buttons to set the required show speed.

Press the “ENTER” button to conrm the setting.

DMX Mode CH-02

CH-15

CH-23

CH-48

Auto Mode Show Mode Auto xx

Show Speed

Operating instructions

Default

001

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems PRO DJ Booth LED Starcloth System Bedienungsanleitung

Equinox Systems

Equinox Systems Hot Rod EQLED089 Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems Six Shooter MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Viper Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT XP MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems HYPE Bedienungsanleitung

Equinox Systems

Equinox Systems PFM1500 Bedienungsanleitung

Equinox Systems

Equinox Systems Flame Machine 1.5M Bedienungsanleitung

Equinox Systems

Equinox Systems Helix 100W Gobo Flower Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED12N Bedienungsanleitung

Equinox Systems

Equinox Systems Spark Stream Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth Quad-colour Starcloth Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten EQLED055 Bedienungsanleitung

Equinox Systems

Equinox Systems Triton Beam EQLED071 Bedienungsanleitung

Equinox Systems

Equinox Systems Crossfire XP Bedienungsanleitung

Equinox Systems

Equinox Systems Beamtastic Bedienungsanleitung

Equinox Systems

Equinox Systems FEVER Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Wash RGBA Bedienungsanleitung

Equinox Systems

Equinox Systems Hallucination Bedienungsanleitung

Equinox Systems

Equinox Systems MoonPar Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Duo RGB Bedienungsanleitung

Equinox Systems

Equinox Systems Ultra LED Scan EQLED75 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED368 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung