Equinox Systems PFM1500 Bedienungsanleitung

Order code: EQLED394

PFM1500

Foam Machine

User Manual

www.prolight.co.uk PFM1500 Foam Machine User Manual 2

Safety advice

WARNING:

FOR YOUR OWN SAFETY, PLEASE READ THIS USER

MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

240V AC, 50Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• This unit is not intended for xed installation.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Prolight

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This xture is for professional use only - it is not designed

for or suitable for household use. The product must be

installed by a qualied technician in accordance with local

territory regulations. The safety of the installation is the

responsibility of the installer. The xture presents risks of

severe injury or death due to re hazards, electric shock

and falls.

• WARRANTY: One year from date of purchase.

• Before your initial start-up, please make sure that

there is no damage caused during transportation.

• Should there be any damage, consult your dealer

and do not use the equipment.

• To maintain the equipment in good working condition

and to ensure safe operation, it is necessary for the user

to follow the safety instructions and warning notes written

in this manual.

• Please note that damages caused by user modications

to this equipment are not subject to warranty.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and the

warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

Before lling the unit disconnect the mains. Never ll with hot liquids.

Only use high quality, water based foam uid recommended by the manufacturer.

Other foam uids may cause clogging and void the guarantee.

Always make sure there is sufcient foam uid present. Operating this foam machine without foam uid will

cause damage to the pump.

Operate the unit only after you have familiarised yourself with its functions. Do not permit operation by persons not qualied

for operating the unit and always drain the tank and use the original packaging if the unit is to be transported.

IMPORTANT: The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the equipment.

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

www.prolight.co.uk PFM1500 Foam Machine User Manual 3

Product overview & technical specications

Designed for large events, the PFM1500 Foam Machine from

Equinox utilises a large, high output fan to project foam up to 10

metres away. Supplied complete with custom designed ight case

for protection during transportation. The robust steel chassis with

built-in tilt mechanism allows the user to direct the output as required.

• Output volume: 5m³ per minute (full on)

• Output distance: 6-8m

• Fluid consumption: 67l/min

• Use with water based foam uid

PFM1500 Foam Machine

Specications

Power consumption 1500W (max.)

Power supply 220-240V, 50/60Hz

Unit dimensions 1040 x 620 x 890mm

Unit weight 32.5kg

Flight case dimensions

with wheels 1220 x 1000 x 680mm

Flight case dimensions

without wheels 1120 x 1000 x 680mm

Flight case weight 36.5kg

Total weight 69kg

Order code EQLED394

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATEWITHOUT

EQUINOX FOAM FLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATEWITHOUT

EQUINOX FOAMFLUID

820mm

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATEWITHOUT

EQUINOX FOAM FLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATEWITHOUT

EQUINOX FOAMFLUID

470mm

830mm

Flightcase included

www.prolight.co.uk PFM1500 Foam Machine User Manual 4

Technical specications

01 - Fan on/off switch

02 - Pump on/off switch

03 - PowerCON TRUE1 input

04 - Fuse: F30A 250V

05 - Bracket adjustment

knobs

06 - Bracket

In the box:

1 x xture,

1 x ightcase with

wheels, 1 x powerCON

TRUE 1 cable

& 1 x user manual

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATEWITHOUT

EQUINOX FOAMFLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DONOT OPERATE WITHOUT

EQUINOXFOAM FLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATE WITHOUT

EQUINOX FOAM FLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATE WITHOUT

EQUINOX FOAM FLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATEWITHOUT

EQUINOX FOAMFLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DONOT OPERATE WITHOUT

EQUINOXFOAM FLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATE WITHOUT

EQUINOX FOAM FLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATE WITHOUT

EQUINOX FOAM FLUID

01 04 02

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATEWITHOUT

EQUINOX FOAMFLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DONOT OPERATE WITHOUT

EQUINOXFOAM FLUID

www.prolight.co.uk PFM1500 Foam Machine User Manual 5

Operating instructions

Installation:

Place the unit on a level surface.

Always disconnect it from the mains supply before lling as uid could be spilled.

If uid should get inside the main housing, disconnect the unit from the mains immediately

and consult a technician.

Install the unit in a well-ventilated area. Use in an insufciently ventilated room can lead to the

condensation of the foam uid. The resulting slippery surface can cause accidents. Keep a minimum

distance of 3m around the unit.

Furthermore do not orientate the output aperture directly in the direction of the audience’s eyes.

In order to create the best effect, there should be a distance between the unit and the audience

of at least 5m.

Only install the foam machine on re resistant, scratch resistant and water resistant surfaces.

This unit is constructed for a free standing installation only. The unit can be used whilst in the base of

the ightcase with the lid removed. Make sure all brakes are applied to the ightcase and the unit.

The operator must always make sure that the safety-relating and machine-technical installations are

approved by an expert before operation for the rst time and after any further changes are made.

The operator has to make sure that the safety-relating and machine-technical installations

are approved by a qualied person once a year.

Important:

Please make sure you connect a substantial uid source as 25 litres of uid will only produce a

maximum of 20 seconds full on foam output. Do not allow the uid source to run dry.

To prevent the unit from overheating it is advised after 20 minutes on continuous operation you stop the

unit outputting foam for approx. 10 minutes so the unit can cool down.

At the end of each operation water must be run through the pump to prevent seizure.

DANGER OF FIRE!

When installing the unit, make sure there is no highly ammable

material (decoration articles etc) within a minimum distance of 3m

DANGER TO LIFE!

Disconnect from the mains before starting maintenance

Only use quality snow uids recommended by your dealer. You must

not use substances which are classied as ‘DANGEROUS WORKING

MATERIALS’ or ‘FLAMMABLE FLUIDS’.

www.prolight.co.uk PFM1500 Foam Machine User Manual 6

Operation:

Connect the foam uid input hose to a sufcient amount of foam uid. Information on this can be found

on the previous page.

Connect the unit to a mains power supply via a powerCON TRUE1 cable.

Now turn on the fan by pressing the green button situated on the top panel.

This will illuminate to indicate the fan is on.

Now turn on the pump by pressing the red button situated on the top panel.

This will illuminate to indicate the pump is on.

Please note: the pump will take a little time to pump the uid through and start outputting.

This should be primed prior to use.

Cleaning and maintenance:

We recommend a frequent cleaning of the unit. Please use a soft lint-free and moistened cloth.

Never use alcohol or solvents!

The uids we recommend are non-hazardous to the environment and can be disposed of via the

sewage system.

There are no serviceable parts inside this unit.

Maintenance and service operations are only to be carried out by authorised dealers.

Replacing the fuse

Only replace the fuse with a fuse of the same type and rating.

Before replacing the fuse, unplug the mains cable.

Procedure:

Step 1: Open fuse holder on the top panel with a screwdriver.

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing.

Should you need any spare parts, please use genuine parts.

Should you have any further questions, please contact your dealer.

Operating instructions

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATE WITHOUT

EQUINOX FOAM FLUID

POWER INPUT:

220-240V~50/60Hz

FUSE:

F30A 250V

FAN WATER

PUMP

DO NOT OPERATE WITHOUT

EQUINOX FOAM FLUID

www.prolight.co.uk PFM1500 Foam Machine User Manual 7

www.prolight.co.uk PFM1500 Foam Machine User Manual 8

WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed of

with other household wastes at the end of its working life. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, please separate this from other

types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their

local government ofce, for details of where and how they can take this item for environmentally

safe recycling.

Business users should contact their supplier and check the terms and conditions of the

purchase contract. This product should not be mixed with other commercial wastes for disposal.

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems Fusion 140 Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Quad Pix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED162 Installations- und Betriebshandbuch

Equinox Systems

Equinox Systems Blitzer Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth Quad-colour Starcloth Bedienungsanleitung

Equinox Systems

Equinox Systems Ultra LED Scan EQLED75 Bedienungsanleitung

Equinox Systems

Equinox Systems Colour Raider Uplighter Pack Bedienungsanleitung

Equinox Systems

Equinox Systems Hot Rod EQLED089 Bedienungsanleitung

Equinox Systems

Equinox Systems Hallucination Bedienungsanleitung

Equinox Systems

Equinox Systems Graphix Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Orbit Bedienungsanleitung

Equinox Systems

Equinox Systems Truss Booth LED Starcloth System CW MKII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED039A Bedienungsanleitung

Equinox Systems

Equinox Systems TAURUS Bedienungsanleitung

Equinox Systems

Equinox Systems Microbor EQLED60 Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion 50 MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED12B Bedienungsanleitung

Equinox Systems

Equinox Systems Kaleido XP Bedienungsanleitung

Equinox Systems

Equinox Systems Midas Spot Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED53 Bedienungsanleitung

Equinox Systems

Equinox Systems Flame Machine 1.5M Bedienungsanleitung

Equinox Systems

Equinox Systems Confetti Burst EQLED400 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung