Equinox Systems Ultra LED Scan EQLED75 Bedienungsanleitung

ORDER CODE: EQLED75

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modifications to this equipment are not

subject to warranty.

Equinox Ultra Scan Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modification to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to flammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualified engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature fluctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualified

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

DMX In

Equinox Ultra Scan Technical specifications

You should find inside the carton the following items:

1, Equinox LED Ultra Scan 2, Power cable 3, User manual

Technical Specifications:

DMX channels: 8

Operating modes: 1, Sound Activated

2, Auto Run

3, DMX

4, Master/Slave

1 x 25W Mega Bright White LED

Colour wheel: 8 dichroic colours + White

Gobo wheel: 11 Gobo’s + Open

4 Push button LED digital display

Beam angle: 11 degrees

Pan: 180˚, Tilt: 90˚

0-100% dimming + strobe function

Mains IEC Power In socket

3-Pin XLR In/Outs sockets for DMX

Power consumption: 50W

Power supply: 240V

Dimensions: 204 x 150 x 465mm

Weight: 4.3Kgs

Overview

Power Input

Button

DMX Out

LED Display

POWER INPUT

FUSE: F2A/250V

POWER INPUT

FUSE: F2A/250V

Down

Button

Enter

Button

Cooling Fan

Operation modes:

DMX mode:

To access the DMX mode, press the “MODE” button on the LED display to show “Addr”. Now

press the “ENTER” button and use the “UP” and “DOWN” buttons to set the desired DMX

address setting from “A001 - A512”.Once you have selected the desired DMX address setting,

press the “ENTER” button a final time.

For DMX functions, please refer to the DMX function chart over leaf

Sound active mode:

To access the sound active mode, press the “MODE” button on the LED display to show “Addr”

and use the “UP” and “DOWN” buttons to display “SOUN”. Now press the “ENTER” button to

access the mode and use the “UP” and “DOWN” buttons to choose from the two options.

Option 1: “ALON”, using this option, the unit(s) will work in sound active mode independently.

Also use this option to set the unit(s) into “SLAVE” mode.

Option 2: “NAST”, using this option will set the unit as the “MASTER” fixture when linking

multiple units.

Once you have selected the desired option, press the “ENTER” button a final time. The unit will

now react to the music.

Auto run mode:

To access the auto run mode, press the “MODE” button on the LED display to show “Addr” and

use the “UP” and “DOWN” buttons to display “AUTO”. Now press the “ENTER” button to

access the mode and use the “UP” and “DOWN” buttons to choose from the two options.

Option 1: “ALON”, using this option, the unit(s) will work in auto run mode independently.

Also use this option to set the unit(s) into “SLAVE” mode.

Option 2: “NAST”, using this option will set the unit as the “MASTER” fixture when linking

multiple units.

Once you have selected the desired option, press the “ENTER” button a final time. The unit will

now run through its built-in programmes.

Reverse pan mode:

To access the reverse pan mode, press the “MODE” button on the LED display to show “Addr”

and use the “UP” and “DOWN” buttons to display “rPAN”. Now use the “UP” and “DOWN”

buttons to turn this mode “ON” or “OFF”. Once you have selected the desired option, press the

“ENTER” button a final time.

Reverse tilt mode:

To access the reverse tilt mode, press the “MODE” button on the LED display to show “Addr”

and use the “UP” and “DOWN” buttons to display “rTIL”. Now use the “UP” and “DOWN”

buttons to turn this mode “ON” or “OFF”. Once you have selected the desired option, press the

“ENTER” button a final time.

Equinox Ultra Scan Operation modes

Operation modes cont....

Display mode:

To access the display mode, press the “MODE” button on the LED display to show “Addr” and

use the “UP” and “DOWN” buttons to display “rDIS”. Now use the “UP” and “DOWN” buttons to

choose “ON” or “OFF” options.

“ON” option: Selecting this option, the LED display will display the right way up.

“OFF” option: Selecting this option, the LED display will display upside down.

Once you have selected the desired option, press the “ENTER” button a final time.

Reset mode:

To access the reset mode, press the “MODE” button on the LED display to show “Addr” and use

the “UP” and “DOWN” buttons to display “rEST”. Now press the “ENTER” button and the unit

will reset itself and return to the last mode it was in.

Loading data mode:

To access the loading data mode, press the “MODE” button on the LED display to show “Addr”

and use the “UP” and “DOWN” buttons to display “LOAD”. Now press the “ENTER” button and

the unit will load up data from a DMX source.

DMX chart:

Equinox Ultra Scan Operation modes

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest flexibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the fixture and each fixture independently.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each fixture requires a

“start address” from 1- 511. A fixture requiring one or more channels for control begins to read the

data on the channel indicated by the start address. For example, a fixture that occupies or uses 7

channels of DMX and was addressed to start on DMX channel 100, would read data from

channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used

do not overlap. E.g. the next unit in the chain starts at 107.

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the

controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all fixtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX fixtures try to use the

shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Equinox Ultra Scan can be controlled via DMX-512 protocol. The DMX address is set on

the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (figure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Equinox Ultra Scan DMX set up

Notice:

• Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Equinox Ultra Scan DMX Set Up

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems EQLED162 Installations- und Betriebshandbuch

Equinox Systems

Equinox Systems Blitzer Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems Scantastic 4 Bedienungsanleitung

Equinox Systems

Equinox Systems 2M Flight CasedDMX LED Flame Machine Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer RGB Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems Six Shooter MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Pulse Tube Bedienungsanleitung

Equinox Systems

Equinox Systems Helix 100W Gobo Flower Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth Quad-colour Starcloth Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Orbit Bedienungsanleitung

Equinox Systems

Equinox Systems Flame Machine 1.5M Bedienungsanleitung

Equinox Systems

Equinox Systems Confetti Burst EQLED400 Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Wash RGBA Bedienungsanleitung

Equinox Systems

Equinox Systems Crossfire XP Bedienungsanleitung

Equinox Systems

Equinox Systems MicroPar UV EQLED028 Bedienungsanleitung

Equinox Systems

Equinox Systems Microbor EQLED60 Bedienungsanleitung

Equinox Systems

Equinox Systems C-Shot Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Quad Bedienungsanleitung

Equinox Systems

Equinox Systems HYPE Bedienungsanleitung

Equinox Systems

Equinox Systems Midas Spot Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Tri MKII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED039A Bedienungsanleitung

Equinox Systems

Equinox Systems Domin8R II Bedienungsanleitung

Equinox Systems

Equinox Systems MoonPar Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung