Equinox Systems HYPE Bedienungsanleitung

HYPE

order code: EQLED40

user manual

www.prolight.co.uk

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Equinox Hype Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the Equinox carton the following items:

1, Equinox Hype 2, Power cable 3, Instruction manual

Technical Specications:

DMX channels: 4

Voltage: AC 110-240V ~ 50Hz/60Hz

156 Ultra bright LED’s (R: 36, G: 36, B:30, W:30, Y: 24)

Fuse: 1 Amp

Power Consumption: 15W

Dimensions: 370 x 220 x 170mm

Weight: 3.1Kg

Operations:

There are 3 operating modes to choose from:

1, DMX Mode 2, Auto Run 3, Sound Active mode

DMX Mode

When the unit is connected with a universal DMX controller, press the “MODE” button to show

“Addr” in the LED display window, you can now set the DMX address from 001-512 using the

“UP” and “DOWN” buttons, once you have set your desired DMX address press the “SET UP”

button to conrm the setting.

Auto Run Function Mode

When the unit is not being used via a DMX controller, press the “MODE” button to show “Func”

in the LED display window. Now press the “SET UP” button and select one of the three following

operation modes using the “UP” and “DOWN” buttons:

1) “Soun” = Sound Active mode

2) “Slav” = Slave mode

3) “Auto” = Auto Run mode

Once you have selected your desired operation mode press the “SET UP” button to conrm

the setting.

Sound Active Mode

To activate the Sound Active mode, rst please make sure that you selected “Soun” in the LED

Display window from the above Auto Run Function Mode. Now press the “SET UP” button and

select one of the 15 different ower effects using the “UP” and “DOWN” buttons.

“P-00” = Runs all 15 ower effects one after another

“P-01”>> “P-15” = Runs selected individual ower effects

Once you have set your desired ower effect press the “SET UP” button to conrm the setting.

To adjust the sound sensitivity in Sound Active mode press the “MODE” button to show “Sens”

in the LED display window, then press the “SET UP” button and adjust the sensitivity using the

“UP” and “DOWN” buttons. Once you have selected your desired sensitivity level, press the

“SET UP” button to conrm your setting. (“S-00” = Low, “S-15” = High)

Equinox Hype Technical specications

Other functions

Slave Mode

To set the unit in the Slave mode, press the “MODE” button to show “Func” in the LED display

window. Now press the “SET UP” button and use the “UP” and “DOWN” buttons to show “Slav”

in the LED display window and press the “SET UP” buton to conrm the setting.

The unit will now run in conjunction with the Master unit when linked together with multiple units.

LED Display On/Off

Press the “MODE” button to show “LED” in the LED display window and press the “SET UP”

button to choose one of the two following options using the “UP” and “DOWN” buttons.

1) “ON” = The LED display will stay ON all of the time

2) “OFF” = The LED dispaly will turn OFF after the setting has been conrmed

Once you have selected your desired option, press the “SET UP” button to conrm your setting

Blackout Mode

Press the “MODE” button to show “Blnd” in the LED display window and press the “SET UP”

button to choose one of the two following options using the “UP” and “DOWN” buttons.

1) “NO” = Auto run mode when the unit is not in Sound Active

2) “YES” = Blackout mode when the unit is not in Sound Active

Once you have selected your desired option, press the “SET UP” button to conrm your setting

DMX Function Chart

Equinox Hype Functions

Function

Blackout Mode

Static colour mode

(Use CH2 to select any of the

24 static patterns/colours)

Sound Active Mode

(Use CH2 to select any of the

30 built-in dynamic patterns

triggered via the internal

microphone)

Channel 1

000-009

010-255

Channel 2

000-009

010-255

000-255

Channel 3

N/A

Strobe Speed

Channel 4

N/A

Master Dimmer

Further DMX cables can be purchased

from all good sound and lighting suppliers

or Prolight dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DATA Cable (DMX cable) requirements (for DMX operation):

• The Equinox Hype can be controlled via DMX-512 protocol. The DMX address is set on the back

of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data

input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Equinox Hype DMX Set up

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Equinox Hype DMX Set up

www.prolight.co.uk

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems EQLED064 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED368 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED138 Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Duo RGB Bedienungsanleitung

Equinox Systems

Equinox Systems Graphix Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED054 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED019 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKII Bedienungsanleitung

Equinox Systems

Equinox Systems C-Shot Bedienungsanleitung

Equinox Systems

Equinox Systems MIRR22 Bedienungsanleitung

Equinox Systems

Equinox Systems Scantastic 4 Bedienungsanleitung

Equinox Systems

Equinox Systems Viper Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Tri MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Triton Beam EQLED071 Bedienungsanleitung

Equinox Systems

Equinox Systems Truss Booth LED Starcloth System CW MKII Bedienungsanleitung

Equinox Systems

Equinox Systems BLITZER Bedienungsanleitung

Equinox Systems

Equinox Systems Waterwave 50W Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten EQLED055 Bedienungsanleitung

Equinox Systems

Equinox Systems FEVER Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Orbit Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems Confetti Burst EQLED400 Bedienungsanleitung

Equinox Systems

Equinox Systems Ultra LED Scan EQLED75 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung