Ericsson I 888 Leitfaden

Approved according to 1776-2/FEA 209 544

Trouble-shooting

instruction

I 888

Standard electrical repairs

4-00021-2/FEA 209 544/5.C

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 2(42)

Table of contents

1 Conditions .......................................................................................... 3

2 No serv or can´t place call. ............................................................... 6

3 Doesn´t start. ................................................................................... 10

4 Audio ................................................................................................ 15

5 Display fault .................................................................................... 21

6 Charging fault ................................................................................. 24

7 SIM fault (Insert card) ................................................................... 27

8 Keyboard ......................................................................................... 29

9 Illumination and buzzer. ................................................................ 33

10 RTC (Real Time Clock) .................................................................. 38

11 IRDA fault. ...................................................................................... 40

12 Component list................................................................................. 42

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 3(42)

1 Conditions

1.1 Component classiﬁcations.

After each component, which fault can be veriﬁed by the troubel-shooting guides in

this folder, is the components classiﬁcation written. The components are divided in

four classes, A,B,C and D. The classes are seperated depending on how much of the

phone´s prestanda that is affected by changing the component.

Class A and B:Changing the component doesn´t affect the prestanda that much,

you only have to do a test call toward a real network before you perform a function

test after replacing it.

Class C: The phone has to be calibrated at station level after changing the com-

ponent, since the components tolerances are so large it can affect the prestanda of

the phone.

Class D: It demands advanced equipment and calibration at board level and

because of that class D-components can´t be replaced.

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 4(42)

1.2 Abbreviations used in the trouble-shooting

instructions.

B: Crystal

C: Capacitor

D: Digital circuit

F: Overload protection

H: Buzzer, ligth diodes, pads to the display

J: Connection

L: Coil

N: Analouge circuit

R: Resistor

U: BALUN. Component that converts a balanced signal to a nonbalanced or the

opposit direction.

V: Transistor, diode

X: Antenna connection, contact point on the board.

Z: Filter

AGND: Ground to analouge signal

DCIO: Direct current through the system connector for charging the bat-

tery.

DCON: Logical signal from the processor that keeps the phone powered on

after releasing the On/Off-button.

GND: Ground

LED3K: Logical signal that activates the illumination.

ONSRQ: Voltage from the On/Off-button that power on the phone.

REGON: Logical signal that activates the regulator for the voltage.

RTC: Real time clock. The clock that shows the time.

SIMCONCLK: Signal from the processor that is used for communication to SIM,

clock.

SIMCONDAT: Signal from the processor that is used for communication to

SIM,data.

SIMCONRST: Signal from the processorn that is used for communication to

SIM,reset.

SIMVCC: Feed voltage to SIM.

SWDC: Switch VBATT

VANA: Voltage to the analouge part of the logical circuit (N800).

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 5(42)

VBATT: Voltage of the battery.

VDIG: Voltage to processor and memories (3.2V).

VDSP: Voltage to DSP (Digital Signal Processor) (3.2V).

VDSPC: Voltage to DSP (Digital Signal Processor) (2.5V).

VLCD: Negative voltage to the display that controlls the contrast (-2.7V).

VDLCD: Feed voltage to the display.

VRAD: Voltage to the radiopart except the synthesizer.

VRPAD: Voltage to the radiopart in D600 (used to top indicator and buzzer).

VRTC: Voltage to the real time clock.

VVCO: Voltage to the syntesizer.

I2C: Communication standard for two-way communication using only 2

wires, for clock and data.

LO: Local oscillator.

PWM: Puls width modulation.

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 6(42)

2 No serv or can´t place call.

2.1 Find out if the fault is related to

Rx(reciever) or Tx(transmitter).

Connect the phone (with signaling program) to a GSM test instrument and try to get

serv at -68.5 dBm on the input signal. If the phone gets serv proceed to section 2.2.

If the phone doesn´t get serv, there is probably a fault in the LO part or too big

losses in the signal path. Open the phone and check for liquid damages. Make sure

the antenna connection X101 (class A) isn´t mecanically damaged, unsoldered or

dirty (varnish, glue, oxide...) (Fig 2.1).

Look for soldering faults on C318 (class A), N302 and N303 (all three Fig 2.1).

Measure the resistance of C530, C531, C532, C533, C534 and C535 (>200 kOhm,

all are class A, Fig 2.1).

Measure the resistance of C850 (>100 kOhm, class A, Fig 2.1), C851 (>1 kOhm,

class A, Fig 2.1), C833 (>1 kOhm, class A, Fig 2.1) and C853 (>100 kOhm, class

A, Fig 2.1).

Measue VVCO and VRAD (3.8V, Fig 2.2). If any of the voltages are incorrect, pro-

ceed to chapter 3 (“Doesn´t start”-fault).

Fig 2.1

X101

C530

C534

C531

C533

C535

C532

N303

N302

C318

N301

C853

C850

C851

C833

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 7(42)

Measure the voltage on pin 4 and 6 on N303 (Fig 2.1). The voltage on pin 4 (the

control voltage) should always vary between 0.8-2.8 V (usually it starts at 1.7 V).

The voltage on pin (the feed voltage) is also variable, but usually it starts at 3.3 V. If

the feed voltage is incorrect (often is it missing completly), check the solderings on

D600:8, D600:102 and also on D105 and D103 (all at Fig 2.2). If the control voltage

is incorrect (mainly 0 or 3.6 V), check the solderings on D600:8 and D600:106-108.

If those are ﬁne, replace N301 (class B, Fig 2.1).

Check the solderings on Z250, Z500, Z201 (GSM 900) and Z202 (GSM1900) (all at

Fig 2.2) plus Z205 (Fig 2.3).

If the fault still remains, send the phone to the next repair level.

Fig 2.2

VVCO

VRAD Z201

Z202

Z250

Z500

D103

N401

L403

N570

N560

L560

B510

D600

D105

128

Fig 2.3

Z204

Z205

Z203

L223

P401

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 8(42)

2.2 Connect a call.

To test GSM900,connect a call at power level 5 against the instrument with the input

signal at -68.5 dBm. To test GSM1900 use power level 0 and an input signal at -68.5

dBm.

If it works, proceed to section 2.3. If it doesn´t work, then it probably is a TX related

fault. If it is only at channel 1 (or several of the lower channels) you can´t connect a

call, is it N570 (class D, Fig 2.2) that is faulty and the phone can´t be repaired at this

level. Open the phone and check for liquid damages. Make sure the antenna connec-

tion X101 (class A, Fig 2.1) isn´t mecanically damaged, unsoldered or dirty (var-

nish, glue, oxide...).

Measure the resstance between test point P401 (Fig 2.3) and ground (or between

N401:14 (Fig 2.2) and ground). The resistance should be larger than 5 kOhm. If it is

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 9(42)

900) and Z202 (GSM1900)(all at Fig 2.2) plus Z205 (Fig 2.3). If the fault still

remains, send the phone to the next repair level.

If the Rx level value is above 45 steps at input signal -68,5 dBm you need to cali-

brate the phone, therefore send the phone to the next repair level.

If the RX quality value is too high, send the phone to the next repair level.

If the output power is too low, check the solderings on N560 (GSM1900) and N570

(GSM900) (both Fig 2.2). Check the solderings on Z205, Z203 (GSM900) and

Z204 (GSM1900)(all three Fig 2.3). If the fault still remains, send the phone to the

next repair level.

I888, Standard Electrical Repairs

4-00021-2/FEA 209 544/5.C 10 (42)

3 Doesn´t start.

3.1 Find out if the phone will start by using the

On/Off-button.

Attach a fully charged battery and press the On/Off-button. If the phone doesn´t

start, proceed to section 3.2. If the phone starts as normal when it is complete, but

shuts down in the trouble-shooting ﬁxture, measure the current consumption. If it is

>1.5 A or as high as the current limit on the power supply, then N401 (class D, ﬁg

3.1) is faulty and the phone can´t be repaired at this repair level. (Measure the resist-

ance between N401:14 and ground, it should be >10 kOhm, but if N401 is faulty it

usually is about 200 Ohm).

If the phone starts, check the charging function by connecting a charger at the sys-

tem connector.If the charging doesn´t work, proceed to chapter 6 (“Charging”-

fault). Open the phone and make a visual check of the board. The side with the com-

ponents are shown in ﬁg 3.1. Check the board for liquid damages and burned or dan-

ages pads at the system connector. Measure the resistance of R421 (0,1 Ohm, class

B, ﬁg 3.1). After every repair of the charging function, you have to verify the

function using the method mentioned in section 6.1.1. Check the solderings on

D600 and D610 (Fig 3.1). As soon as the fault has been corrected, send the phone

back into the normal repair ﬂow. If the phone starts and the values above are correct,

it is either without faults or there is an intermittent fault.

Fig 3.1

N401

N412

N410

N411

N701

VDSP

VVCO

VRPAD

VRAD

VDIG

C692

D600

N702

D610

N703R725C710

B510

128

R421

Inhaltsverzeichnis

Andere Ericsson Telefon Handbücher

Ericsson

Ericsson Dialog 3210 Bedienungsanleitung

Ericsson

Ericsson OPI 3214 Bedienungsanleitung

Ericsson

Ericsson R250S Bedienungsanleitung

Ericsson

Ericsson BusinessPhone 250 Bedienungsanleitung

Ericsson

Ericsson Dialog 4223 Professional Bedienungsanleitung

Ericsson

Ericsson Dialog 4225 Vision Bedienungsanleitung

Ericsson

Ericsson Dialog 4187 Plus Bedienungsanleitung

Ericsson

Ericsson Basic telephone Bedienungsanleitung

Ericsson

Ericsson Dialog 4186 High Bedienungsanleitung

Ericsson

Ericsson MD110 Bedienungsanleitung

Ericsson

Ericsson DIALOG 4223 PROFESSIONAL - 2 Bedienungsanleitung

Ericsson

Ericsson DIALOG Stücklistenhandbuch

Ericsson

Ericsson Dialog 4223 Professional Bedienungsanleitung

Ericsson

Ericsson dialog 4106 Bedienungsanleitung

Ericsson

Ericsson BP50 Bedienungsanleitung

Ericsson

Ericsson DT290 Bedienungsanleitung

Ericsson

Ericsson LDP-7208D Bedienungsanleitung

Ericsson

Ericsson Dialog 4422 Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Ericsson

Ericsson Ericofon Leitfaden

Ericsson

Ericsson Dialog 3211 Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Ericsson

Ericsson Dialog 4223 Professional Bedienungsanleitung

Ericsson

Ericsson Dialog 3211 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung