ESAB PREST-O-LITE PZ-503 Bedienungsanleitung

INSTRUCTIONS for 0558005336

January, 2005

PREST-O-LITE™ PZ-503 Self Lighting Torch - P/N 22533

These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles

of operation and safe practices for air-fuel gas equipment, we urge you to read our booklet “Precau-

tions and Safe Practices for Gas Welding, Cutting & Heating,” Form 2035. Do NOT permit untrained

persons to install, operate, or maintain this equipment. Do NOT attempt to install or operate this

equipment until you have read and fully understand these instructions. If you do not fully understand

these instructions, contact your supplier for further information.

CAUTION

WARNING

This is a ﬂame producing device using pressurized Propane or Mapp fuel gas. This equipment will ignite

instantly to produce an extremely hot temperature of over 2000 degrees and will heat or damage mate-

rial in seconds. Heat from this torch can travel further than the eye can see. Make sure no combustible

materials are unintentionally exposed to heat or ﬂames. Disconnect torch from tank when not in use. Im-

proper assembly, abuse or misuse can cause serious injury. Before each use, check for leaks. Do not use

if leak cannot be corrected. Store fuel tank in a well ventilated area. This is not intended to be a complete

training manual. Each situation has its own safety issues that the user must address.

Gas can get trapped inside the torch, even after the cylinder is removed. Always assume the torch has

enough trapped gas to ignite and cause a dangerous situation. Point torch away from yourself and other

items that can be damaged.

Always use torch in well-ventilated, non-enclosed work area to avoid possible health hazards from fumes.

Do not operate torch upside down or in a horizontal position as the tank will discharge liquid causing the

ﬂame to increase or ﬂare up. If this happens, immediately turn the torch right side up or turn it oﬀ. When

the liquid fuel has burned oﬀ or evaporated, the torch will then operate normally.

Keep combustible material away from or protected from the ﬂame.

The torch’s tip end will get very HOT and can cause a burn if touched.

Do not store the fuel tank in a room used for habitation, in a closed or conﬁned space, near open ﬂames,

heaters, or in direct sunlight.

Do not leave work area hot.

Do not drop tank or torch or handle roughly.

Do not look into tip end or point at non-work objects.

Do not leave a burning torch unattended.

Do not leave the Ignition Button on and valve open when not in use.

Do not heat objects that contain or have contained ﬂammable liquids or vapors.

Do not alter or tamper with the torch. Return torch for proper repairs.

Always keep out of the reach of children.

Always disconnect the torch from the tank when not in use.

Always wear eye protection when using the torch.

Always have water or a ﬁre extinguisher ready.

Comply with all Federal, State and Local Government regulations and standards.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

TIP END

FLAME TUBE GAS ADJUSTMENT VALVE

INLET CONNECTION

FLAME LOCK BUTTON

ON/OFF IGNITION BUTTON

INSTRUCTIONS FOR PROPER USE AND CARE

ASSEMBLY

Prior to assembly, inspect o-rings, washers, connections and equipment for damage, dirt or grease. Do not

use if damaged.

Before attaching the torch to the tank, turn ON/OFF Ignition Button to the OFF position and turn gas ad-

justment valve clockwise to the closed position. Do not force knob as it may bind or damage the valve.

Screw the torch onto the gas tank. Press down and turn clockwise. Hand tighten. Do not use a wrench or

other tools to tighten.

LIGHTING

Before each use check connections for leaks using a soapy water so-

lution or leak detector ﬂuid.

To light hand torch, turn Ignition Button to the ON position and turn the Gas Adjustment Valve coun-

terclockwise then squeeze Ignition Button to light. If torch doesn’t light turn Gas Adjustment Valve and

squeeze button. Never look into tip end.

Push Flame Lock Button down when a continuous ﬂame is desired. To release Flame Lock, squeeze and

release Ignition Button.

FLAME ADJUSTMENT

Adjust ﬂame so that wide portion of ﬂame is away from end of tip. If ﬂame is too small, tip end will over-

heat beyond its normal heating to a red color. Obtain maximum performance by positioning the ﬂame

between 1 and 2 tip diameters from the object being heated.

TORCH SHUT-OFF

Release Ignition Button to shut ﬂame oﬀ or squeeze Ignition Button and release when using the Flame

Lock feature.

Disconnect the fuel tank from the torch. Do so in a well-ventilated area away from sources of ignition. It

should be expected that trapped gas inside the torch will be expelled from the torch.

Point torch away from yourself and objects, then squeeze Ignition Button to release any additional trapped

gas inside torch.

Turn the Ignition Button to OFF and close the Gas Adjustment Valve.

STORAGE

Disconnect the torch from the fuel tank.

Store fuel tank in a well-ventilated area away from sources of ignition.

WARNING

TOO SMALL CORRECT FLAME TOO BIG

Be sure this information reaches the operator.

You can get extra copies through your supplier.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißzubehör Handbücher

ESAB

ESAB PSF 305 Bedienungsanleitung

ESAB

ESAB Eye-Tech 10-12 Select Bedienungsanleitung

ESAB

ESAB LHI 825 Bedienungsanleitung

ESAB

ESAB WeldCloud Mobile Bedienungsanleitung

ESAB

ESAB PREST-O-LITE 02X93 Bedienungsanleitung

ESAB

ESAB TWECO SPRAY MASTER V250 Wartungs- und Serviceanleitung

ESAB

ESAB PSF 250 Bedienungsanleitung

ESAB

ESAB PSF 260C Bedienungsanleitung

ESAB

ESAB Origo Feed 304 P4 Leitfaden

ESAB

ESAB SDE-250 Bedienungsanleitung

ESAB

ESAB Sentinel A60 Bedienungsanleitung

ESAB

ESAB PSF 260 Bedienungsanleitung

ESAB

ESAB Aristo U6 Bedienungsanleitung

ESAB

ESAB ET 17 Bedienungsanleitung

ESAB

ESAB 1500 ahma Bedienungsanleitung

ESAB

ESAB Aristo U8 Bedienungsanleitung

ESAB

ESAB CIGWELD 454342 Bedienungsanleitung

ESAB

ESAB CIGWELD Arcmaster 649 Payday Bedienungsanleitung

ESAB

ESAB SABRE V J28 Bedienungsanleitung

ESAB

ESAB Sentinel A50 Bedienungsanleitung

ESAB

ESAB A6 S Arc Master Bedienungsanleitung

ESAB

ESAB TR-29 Bedienungsanleitung

ESAB

ESAB EDB-15/30 Bedienungsanleitung

ESAB

ESAB A2 S GMAW Mini Master Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Lincoln Electric

Lincoln Electric LT-7 Tractor Bedienungsanleitung

Weco

Weco Trolley R Bedienungsanleitung

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

optrel

optrel lifeflip autopilot Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung