ESAB TR-29 Bedienungsanleitung

INSTRUCTIONS for

TR-29 TWO CYLINDER TRUCK KIT

Item No. 37924

for mounting:

353cv, 453cv, 653cvcc, MultiPower 460 and MultiPower 460 Pulse Power Sources

F15-592-B

March, 2003

This kit includes the following components:

1 — Assembled TR-29 Truck Body

1 — Cylinder Support

2 — Chain, 2/0 36" (not illustrated)

2 — Nuts 1/4" x 20 Lock

2 — Washer 1/4" Fender

4 — Screws 1/4"-20 1" Long

F15-592-B

Location of Screws

and U-Slots.

To mount Power Source on Truck, proceed as fol-

lows:

1. Carefully lift the power source off the floor with a

craneorhoistandremoveanyskidsfromthebase.

2. Lower the unit onto the truck base aligning the two

protruding screws on the rear bottom of the power

source (see photos above), with the U-slots pro-

vided in the truck base. The rear slots are located

just in front of the wheel guards. Note also that all

protruding bolt heads on the bottom of the power

sourcehaveaholedrilled in the truck floor for them

to pass through. When the Power Source is prop-

erly seated on the truck the weight of the unit is on

the floor of the truck not the side rails, and the front

floor of the truck will be flush with the lower front

panel of the Power Source.

Weight Bearing Area

(OPTIONAL)

- Install 1/4-20 Lock Nuts

on these screws once

assembled to the Truck Kit.

4. The cylinder support is installed by first removing

the four corresponding (assembly screws) on the

topfourcornersofthepower source.(SeeFigure4

onreverseside.) Setthesupportontopofthepower

sourceandinstallthelonger screwsprovided. (Note)

If top does not lay flush, loosen screws on handle

and retighten after assembly.

3. If bolting the power source to the base, 2 screws

should protrude through the TR-29 Floor from the

base of the power source. Attach one .250 flat

washer and one .250 lock nut to each screw.

This truck assembly is not intended to be hoisted

while attached in any way to a power source. If the

unit must be hoisted, the truck assembly must be

removed.

NEVERATTEMPT TOLIFTAPOWERSOURCE WITH

CYLINDER(S)ATTACHED!

5. Adjust cable strain relief bar to suitable height (see

Figure 3).

Be sure this information reaches the operator.

You can get extra copies through your supplier.

Figure 1

Figure 2

6. To mount cylinders on completed assembly:

Slide at least the second link of each chain (678944)

into the center slot of the cylinder support.

Whenyou putthecylinders in place,pullthe chaintightly

aroundeach cylinder andslidea chain link intotheouter

slotof the cylinder support. Besure to pull the linkdown

firmly into each slot to secure the chain so that there is

littleslack of the chain about the cylinder. DO NOTjust

"loop" a link over the end of the support.

Cylinder support

assembly screws

Handle

Floor of Truck is flush

with lower panel of

Power Source.

Cable Strain Relief Bar

F15-592-B 03 / 2003

Figure 3 Figure 4

Assembly Screws on

Left Side not visible.

READ & UNDERSTAND THIS LABEL

PROTECT YOURSELF AND OTHERS

LIRE & COMPRENDE CETTE ETIQUETTE

VOUS PROTEGER ET LES AUTRES

Lifting eye to be used for lifting

power source ONLY.

Do NOT use when additional accessories

are attached to power source.

L’oeil d’ascenseur etre utilise

pour la source de pouver seulement.

ont attachesa la source de pouvoir.

PRUDENCE

P/N 99512240-C 3/22/02

Dieses Handbuch passt für folgende Modelle

Andere ESAB Schweißzubehör Handbücher

ESAB

ESAB A6 S Arc Master Bedienungsanleitung

ESAB

ESAB PT-31XL Bedienungsanleitung

ESAB

ESAB A6 Mastertrac Bedienungsanleitung

ESAB

ESAB Aristo U6 Bedienungsanleitung

ESAB

ESAB PSF 315ME Bedienungsanleitung

ESAB

ESAB LHI 825 Bedienungsanleitung

ESAB

ESAB Aristo U8 Bedienungsanleitung

ESAB

ESAB SABRE V J28 Bedienungsanleitung

ESAB

ESAB Sentinel A60 Bedienungsanleitung

ESAB

ESAB A6 GMD Bedienungsanleitung

ESAB

ESAB WeldCloud Mobile Bedienungsanleitung

ESAB

ESAB CIGWELD 454342 Bedienungsanleitung

ESAB

ESAB SDF-50 Bedienungsanleitung

ESAB

ESAB Eye-Tech 11 Mono Bedienungsanleitung

ESAB

ESAB SDE-250 Bedienungsanleitung

ESAB

ESAB PSF 250 Bedienungsanleitung

ESAB

ESAB Origo Feed 304 P4 Leitfaden

ESAB

ESAB PSF 260 Bedienungsanleitung

ESAB

ESAB Eye-Tech 10-12 Select Bedienungsanleitung

ESAB

ESAB EDB-15/30 Bedienungsanleitung

ESAB

ESAB ET 17 Bedienungsanleitung

ESAB

ESAB CIGWELD Arcmaster 649 Payday Bedienungsanleitung

ESAB

ESAB SCT-4200 Series Bedienungsanleitung

ESAB

ESAB PSF 305 Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Lincoln Electric

Lincoln Electric LT-7 Tractor Bedienungsanleitung

Weco

Weco Trolley R Bedienungsanleitung

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

optrel

optrel lifeflip autopilot Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung