ESAB PT-31XL Bedienungsanleitung

PT-31XL and PT-31XLPC

Plasma Arc Cutting Torches





This equipment will perform in conformity with the description thereof contained in this manual and accompa-

nying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instruc-

tions provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment

should not be used. Parts that are broken, missing, worn, distorted or contaminated should be replaced imme-

diately. Should such repair or replacement become necessary, the manufacturer recommends that a telephone

or written request for service advice be made to the Authorized Distributor from whom it was purchased.

This equipment or any of its parts should not be altered without the prior written approval of the manufacturer.

The user of this equipment shall have the sole responsibility for any malfunction which results from improper

use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a ser-

vice facility designated by the manufacturer.









             

















1.0 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

2.0 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

2.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

2.2 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

2.3 Technical Data (required by CE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

3.0 Installation / Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

3.1 Torch / Consumables Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

3.2 Disassembly of Torch - Removing Consumables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

3.3 Installing Consumables - Assembly of Torch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

4.0 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

4.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

4.2 Repositioning Torch Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

5.0 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

5.1 Deﬁnitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

5.2 Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

5.3 PT-31XL and PT-31XLPC Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

         



 

 

Users of ESAB welding and plasma cutting equipment have the ultimate responsibility for ensuring that anyone

who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet

the requirements that apply to this type of welding or plasma cutting equipment. The following recommendations

should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well acquainted with the operation of the welding or plasma

cutting equipment. Incorrect operation of the equipment may lead to hazardous situations which can result in

injury to the operator and damage to the equipment.

1. Anyone who uses welding or plasma cutting equipment must be familiar with:

- its operation

- location of emergency stops

- its function

- relevant safety precautions

- welding and / or plasma cutting

2. The operator must ensure that:

- no unauthorized person stationed within the working area of the equipment when it is started up.

- no one is unprotected when the arc is struck.

3. The workplace must:

- be suitable for the purpose

- be free from drafts

4. Personal safety equipment:

- Always wear recommended personal safety equipment, such as safety glasses, ﬂame proof

clothing, safety gloves.

- Do not wear loose ﬁtting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions:

- Make sure the return cable is connected securely.

- Work on high voltage equipment .

- Appropriate ﬁre extinquishing equipment must be clearly marked and close at hand.

- Lubrication and maintenance  be carried out on the equipment during operation.

 



          

        



 - Can kill.

- Install and earth (ground) the welding or plasma cutting unit in accordance with applicable standards.

- Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

- Insulate yourself from earth and the workpiece.

- Ensure your working stance is safe.

 - Can be dangerous to health.

- Keep your head out of the fumes.

- Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

 - Can injure eyes and burn skin.

- Protect your eyes and body. Use the correct welding / plasma cutting screen and ﬁlter lens and wear

protective clothing.

- Protect bystanders with suitable screens or curtains.



- Sparks (spatter) can cause ﬁre. Make sure therefore that there are no inﬂammable materials nearby.

 - Excessive noise can damage hearing.

- Protect your ears. Use earmuﬀs or other hearing protection.

- Warn bystanders of the risk.

 - Call for expert assistance in the event of malfunction.







 

The patented PT-31XL and PT-31XLPC are manual torches with a 75° head designed for use with several plasma arc cutting

packages using clean, dry air as the plasma gas. The service lines are 4.5, 7.6 or 15.2 meters (15, 25 or 50 feet) long and the

torch is rated to operate up to 50 amperes at 100% duty cycle for cutting most metals.



















2 1/4"

(57mm)



5 1/4"

(133mm)





5 1/4"

(133mm)

2 7/8"

(73mm)

PT-31XLPC, 7.6m ................................................................................................................................................................................... 0558005393



A spare parts kit is recommended for maintaining the torch with minimum downtime. A spare parts kit is supplied with each

plasma cutting package.





35/40A XT Spare Parts Kit (Extended Life) ................................................................................................................................................ 21980



30/40A Standard Spare Parts Kit (High Performance) .............................................................................................................0558003301



The high performance kit (0558003301) is the preferred kit and is included with all of the above

referenced plasma cutting systems.

 







 

    

      

   

Heat Shield 20282 1 1

Heat Shield, Long "CE" 0558000509 (36284) 1 1 1

30/40 amp High

Performance Nozzle 0558000512 (20860) 3 3

35/40 amp Extended

Life Nozzle 0558000508 (21008) 3 3

Nozzle, 50 amp 0558000513 (20861) 3

Swirl Baﬄe 0558000506 (20463) 1 1 1 1 1

Electrode 0558000507 (20862) 2 2 3 2 2

O-ring 0558000514 (950790) 1

Lubricant (0.25 ounce) 0558000443 (17672) 1 1 1



This valuable troubleshooting tool allows measurement of

the actual plasma gas ﬂow through the torch 0558000739



This complete kit, in a rugged plastic carrying case, includes

attachments for circle and straight line cutting on ferrous and

non-ferrous metals.

Deluxe, 1-3/4" - 42" (44.5mm-1060mm) Radius ..............................................................................................................................................................................0558003258

Basic, 1-3/4” - 28” (44.5mm-710mm) Radius ....................................................................................................................................................................................0558002675

a. Process:

Manual torch used for plasma arc cutting

b. Method of guidance:

Manual

c. Voltage class:

M (113v peak to 400v peak)

Striking voltage: 8000 VAC

Stabilizing voltage: 200 VDC

d. Maximum rated current: 50 amps

Maximum current at 100% duty cycle: 50 amps

Type gas: 120 I/min. at 5.5 bar (254 cfh at 80 psi)

e. Max. and min. gas pressure at inlet: 4.8 to 5.9 bar (70 to 86 psi)

f. Type of cooling:

Air

g. Rating of auxiliary electrical control in torch:

N/A

h. Requirements for connection of torch:

Wrenches and screwdriver

i. Essential information about safe operation of torch:

Refer to all safety precautions in manual

j. Essential information about safe operation of the plasma cutting torch and the functioning of interlocking and safety

devices:

Meets requirements by means of pneumatic interlock safety system. The interlocking device deenergizes the torch

when parts, particularly protective cone, are removed to expose electrode connection. For the interlocking device

to function properly, the torch electrode must remain in the protective cone. Do not attempt to install the electrode

into the torch without ﬁrst placing it in proper position (with the other parts) within the protective cone.



k. Type of plasma cutting power source that can form a safe system with the plasma cutting torch:

PCM-500i, PowerCut 650, HandyPlasma 550, HandyPlasma 380, HandyPlasma 50 and Caddycut.

I. Plasma cutting ability:

See Graphs 2-1a and 2-1b on following page:

 





.750

160

140

120

100



2032

1524

1016

508

254

003 6 10 13 16



4064

3556

3048

2540

 



100

0.125 .250 .375 .500 .625







.125 .250 .375 .500 .625





 

Andere Handbücher für PT-31XL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB 100i Bedienungsanleitung

ESAB

ESAB Precision Plasmarc Betriebsanleitung

ESAB

ESAB A2 Multitrac Bedienungsanleitung

ESAB

ESAB EASY-WELD SSR 400 Betriebsanleitung

ESAB

ESAB AristoMig U400 Bedienungsanleitung

ESAB

ESAB Caddy Arc 251i Bedienungsanleitung

ESAB

ESAB THERMAL DINAMICS CUTMASTER 60i Bedienungsanleitung

ESAB

ESAB Aristo WeldCloud Mig U5000i Bedienungsanleitung

ESAB

ESAB Cigweld EasyWeld 160 Bedienungsanleitung

ESAB

ESAB RobustFeed PRO Bedienungsanleitung

ESAB

ESAB Caddy Arc 152i Bedienungsanleitung

ESAB

ESAB Origo Mig 410 Bedienungsanleitung

ESAB

ESAB ESABMig 405 Bedienungsanleitung

ESAB

ESAB Rogue ES 130i PRO Bedienungsanleitung

ESAB

ESAB MT-450W Bedienungsanleitung

ESAB

ESAB PCM-750i Bedienungsanleitung

ESAB

ESAB Origo Mig 4004i A44 Bedienungsanleitung

ESAB

ESAB Railtrac B42V Bedienungsanleitung

ESAB

ESAB Aristotig 255 AC/DC Bedienungsanleitung

ESAB

ESAB POWERCUT-1250 Einrichtungshandbuch

ESAB

ESAB CIGWELD WeldSkill MicroArc 140 Bedienungsanleitung

ESAB

ESAB Aristotig255 AC/DC DTE 255 Bedienungsanleitung

ESAB

ESAB Tig 4000i Aristo Bedienungsanleitung

ESAB

ESAB Rogue ES 180i Pro Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung