ESI AA100 Kurzanleitung
INSTALLATION AND USE
AA100
ARTICULATING KEYBOARD ARM
AA100 Rev A 4/17
Model AA100
1
/2"
Drill 1
/8" Pilot Holes
Where Indicated
Underside of
Work Surface
AA100 ARTICULATING KEYBOARD ARM
PLEASE REVIEW these instructions before beginning the installation. Check that
all parts needed were provided with your order. Contact your supplier if any
operates to your satisfaction.
PARTS PROVIDED
Articulating Arm (1)
Front Stop (1) Track Extender (1)
Track (1)
2
Cord Clip (1) 5
/8" Wood
Screws (20*)
*Includes Extras
*Optional
Rear Bumper* (1)
ADDITIONAL TOOLS REQUIRED
• •
Drill with
STEP 1: Drill Pilot Holes for Attaching Track
• Position one end of the track 1
/2" from the front
edge of the work surface.
• Drill 1
/8" pilot holes through the seven h
indicated in the illustration.
— Drill the holes 5/8" deep.
CAUTION: Be careful not to
drill through the top of the work
surface.
With this short 13" track, the track
extender is normally used as the rear
stop. If the rear bumper will be used
instead, drill a pilot hole is the center
rear hole and do not drill pilot holes
in the two rear side holes.
#2 Phillips drill bit
1
/8" bit
oles
CAUTION: This install requires a power drill.
This is not a hand tool install
AA100 ARTICULATING KEYBOARD ARM
STEP 2: Attach Track
• First attach the track through the
four center holes, as shown.
• Then attach the track
extender through the two
rear holes.
• Do not attach a screw through
the front center hole at this time.
STEP 3: Install Articulating Arm
• Slide the articulating arm onto the track.
Position it back far enough so that you
have access to the front center hole
on the track.
STEP 4: Attach Front Stop
• Position the front stop onto the
front of the track and secure it with
a screw through the center hole.
• Drill pilot holes for the two side
screws and attach the ends of
the front stop with two more
screws.
Attach Through
Four Center Holes
Then Attach
Track Extender
Slide
Back
Front
Stop
3
© 2017 ESI Ergonomic Solutions. All rights reserved. AA100 Rev A 4/17
AA100 ARTICULATING KEYBOARD ARM
OPERATION
To Tilt:
• Loosen the ratchet handle, adjust the tilt angle, then tighten the handle.
To Telescope:
• Lift the front of the platform and slide it inward to stow or outward to access.
To Raise:
• Grasp both sides of the platform and raise to the desired height.
To Lower:
• Grasp both sides of the platform, tilt up the front, and move down to the
desired height.
800.833.3746 esiergo.com
Andere ESI Rack & Stand Handbücher
ESI
ESI Solution 6CC Kurzanleitung
ESI
ESI LIFT ERGORISE Bedienungsanleitung
ESI
ESI AA780DAT Bedienungsanleitung
ESI
ESI E-AMT Bedienungsanleitung
ESI
ESI EVOLVE Series Montageanleitung
ESI
ESI Kata Series Bedienungsanleitung
ESI
ESI Kata EX2-FMS Bedienungsanleitung
ESI
ESI LTH-EDGE Bedienungsanleitung
ESI
ESI AA355DS Bedienungsanleitung
ESI
ESI Kata EX2-MS Series Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
