ESI EPPA2-KIT Bedienungsanleitung

ASSEMBLY AND ADJUSTMENT

EPPA2-KIT Model EPPA2-KIT-XXX

DUAL MONITOR ARM CONVERSION

EPPA2-KIT Rev A 10/17

PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check that

all the parts and tools listed below were provided with your order. Contact your supplier if any materials are

missing. Do not discard the packaging until content that the product operates to your satisfaction.

EPPA2-KIT PARTS AND TOOLS

Base and Monitor Arm Assembly (1) Clamp L-Bracket (1)Clamp (1) Plastic Cap (1)

Grommet Mount Plate (1)Clamp Pad (1) Grommet Bar (1)

Grommet Knob (1)

PARTS AND TOOLS PROVIDED

CAUTION: Hand-tighten screws only.

Grommet Bolt (1)

M8x104

Monitor Screw Washer (8)

Monitor Screw (8)Socket Cap Screw (2) Monitor Screw (8)Flat Head Screw (3)

M6x12M6x10

M4x12M5x12

6mm Allen Key (1)5mm Allen Key (1)4mm Allen Key (1)

ADDITIONAL TOOLS REQUIRED

• Phillips screwdriver

Disconnect and Remove the Monitor from EPAA Single Arm System

The monitor arm and its base components are reused when converting to a dual arm system. The rst step

in this process is removing the monitor from the monitor arm.

Remove Cable Covers

The cable covers on the underside of the monitor arm must be

removed before removing the monitor.

• Slightly pull apart the ends of the upper cable cover to

remove it from mounting holes on the monitor arm.

• Slide the lower cable cover up toward the

monitor to remove it. Do not attempt

to snap it off.

• Unplug the monitor cable and

power cord.

Remove Monitor

• Remove the bottom two screws securing the monitor to the VESA mount.

• While supporting the monitor, loosen but do not remove the top two screws.

• Lift off the monitor and place it face down on a soft, at surface.

NOTE: If the inner holes on the VESA mount were used to attach the monitor, after loosening the top two

screws, lift the monitor and pull the screws through the large part of the keyhole opening.

MONITOR REMOVAL EPPA2-KIT

M4x12 or

M5x12

Loosen

Screws Lift Off

Monitor

Remove and Disassemble the Single Arm Base Assembly

The base assembly must be removed and disassembled in order to remove the monitor arm. Follow the

procedures below for the particular method used to attach the base to the worksurface.

IMPORTANT: Recycle the single arm base assembly. Contact ESI Customer Service at 1-800-833-3746.

Clamp Method

1. Turn the knob to loosen the clamp. Remove the base assembly from the worksurface.

2. Remove the clamp from the clamp L-bracket using the 5mm Allen key.

3. Peel the clamp pad from the base and L-bracket.

4. Remove the clamp L-bracket from the underside of the base using the 4mm Allen key.

Grommet Method

• Unscrew the grommet knob and remove the grommet bar.

• Remove the base assembly from the worksurface.

EPPA2-KIT BASE ASSEMBLY REMOVAL

M6x12

Flat Head

4mm

Allen Key

3.2.

M6x10

Socket Cap Remove

Clamp

Pad

Loosen

5mm

Allen

Key

Remove

Base Assembly

Remove

Grommet Bar

Unscrew

Grommet

Knob

MONITOR ARM REMOVAL EPPA2-KIT

Grommet Method (continued)

1. Peel the clamp pad from the base and grommet

mount plate.

2. Remove the grommet mount plate and grommet

bolt. Use the 4mm Allen key to remove the three

M6x12 at head screws.

M6x12

Flat Head

Grommet

Mount

Plate

4mm

Allen Key

2.1.

Remove

Clamp Pad

Remove the Monitor Arm and Other Components from the Single Arm Base Assembly

• From the bottom of the base assembly, use the 6mm Allen key to remove the socket head screw that

holds the monitor arm in place.

— Save the screw and washer for re-use.

• Remove the monitor arm from the base assembly.

• Remove the other base assembly components shown below and save for re-use.

Top Bushing

Save for Re-Use:

Bottom Bushing

Shaft Washer

Curved Washer

M7x16

Socket Head

Screw

EPPA2-KIT MONITOR ARM INSTALLATION

Install the Monitor Arm and Other Components onto the Dual Arm Base Assembly

• At the top of the dual arm base assembly, place the top bushing onto the protruding rim. Then insert the

monitor arm that you removed from the single arm base assembly.

• From the bottom of the base assembly, install the bottom bushing. If necessary, tap it down so that the

monitor arm stem protrudes slightly from the bushing.

• Fit the shaft washer over the stem, aligning the at sides of the washer with the at sides of the stem.

• Fit the curved washer over the socket head screw with its outer curve against the screw head. The

concave side of the washer will be against the shaft washer.

• Use the 6mm Allen key to fasten the socket head screw into the monitor arm stem.

— Securely tighten the screw.

• Check that the monitor arm can rotate without difculty. If it cannot, check that you have installed all

re-used components correctly.

Dual Arm

Base Assembly

Top Bushing

Parts to Re-Use:

Bottom Bushing

Shaft Washer

Curved Washer

M7x16

Socket Head

Screw

Clamp Method

With the clamp method, the clamp L-bracket, clamp, and clamp pad are assembled to the base.

1. Attach the clamp L-bracket to the underside of

the base. Use the three M6x12 at head screws

and the 4mm Allen key.

2. Peel the adhesive backing from the clamp pad

and attach the pad to the base and L-bracket.

3. Attach the clamp to the clamp L-bracket using

the two M6x10 socket cap screws and the

5mm Allen key. Then snap the plastic cap onto

the back of the L-bracket.

A. Attach the clamp to the top two holes if the

thickness of the worksurface is between 3/8"

(10mm) and 21

/8" (55mm).

B. Attach the clamp to the bottom two holes if

the thickness of the worksurface is between

/8" (55mm)and 31

/4" (85mm).

Install Base Assembly

• Clamp the base assembly to the worksurface in the desired position. Be sure to tighten the knob securely.

• Proceed to “Monitor Installation” on page 9.

Base Assembly Attachment Methods

Typically, you will use the same method to attach

the dual arm base that was used to attach the

single arm base.

• Clamp method. The base assembly is clamped to

a table or desk surface that is between 3/8" (10mm)

thick and 31

/4" (85mm) thick. See below.

• Grommet method. The base assembly is secured

through a grommet hole in the worksurface.

Surface thickness must be between 3/8" (10mm)

and 31

/4" (85mm). See page 8.

DUAL ARM BASE ASSEMBLY INSTALLATION EPPA2-KIT

Clamp

Method

Grommet

Method

Clamp Pad

4mm

Allen Key

M6x12

Flat Head

1. 2.

3A. 3B.

M6x10

Socket Cap

5mm

Allen

Key

Plastic

Cap

Plastic

Cap

Grommet Method

This method can be used for worksurfaces that have a grommet hole in

an appropriate position. First, the grommet bolt and grommet mount plate

are assembled to the base. Then, with the base assembly placed over the

grommet hole, the grommet bar and grommet knob are used to secure

the base assembly in position.

1. With the countersunk holes on the bottom, insert the grommet bolt through

the top of the grommet mount plate. Attach the plate to the underside of

the base using the three M6x12 at head screws and the 4mm Allen key.

2. Peel the adhesive backing from the clamp pad and attach the pad to the

base and grommet mount plate.

Install Base Assembly

• Place the base assembly over the grommet hole, with the bolt centered.

• Place the grommet bar onto the grommet bolt and then screw on the grommet knob. Tighten the

grommet knob securely to hold the base assembly in position.

• Proceed to “Monitor Installation” on page 9.

EPPA2-KIT DUAL ARM BASE ASSEMBLY INSTALLATION

Clamp

Method

Grommet

Method

M6x12

Flat Head

Grommet Bolt

Grommet

Mount Plate

4mm

Allen Key

Clamp

Pad

1. 2.

Center Over

Grommet Hole

Tighten Knob

to Secure

Grommet Bar

Grommet Knob

MONITOR INSTALLATION EPPA2-KIT

Attach Monitors to VESA Mounts

There are two sets of four holes on each VESA mount. One set has holes 3.9" (100mm) apart, the other set

has holes 3" (75mm) apart. Use the set that matches the holes on the monitor.

• Place the monitor face down on a at surface.

• Attach D5 washers and M4x12 or M5x12 screws (depending on monitor hole size) to the top two holes on

the monitor. Leave 1

/8" to 3/16" (3mm to 5mm) of exposed threads between the washer and monitor.

— If using the inner holes on the VESA mount, do not use the washers. The screw heads without washers

will t through the large part of the keyhole openings.

• Hook the monitor onto the VESA mount, as shown.

• Install and tighten screws and washers into the bottom two holes. Then tighten the top two screws.

• Repeat for the second monitor.

Capture Monitor Cables and Power Cords

Cable covers on the underside of each monitor arm are used to neatly

organize the monitor cable and power cord.

Remove Cable Covers

• Slide the lower cable cover up toward the

monitor to remove it. Do not attempt to

snap it off.

• Pull apart slightly the upper and lower

ends of the other cable cover to

remove it from mounting holes

on the monitor arm.

M4x12 or

M5x12

Install Cable Covers

• Install the upper cable cover with the monitor cable and power cord

captured. Pull apart slightly the upper and lower ends of the cover to t

it over the mounting holes on the monitor arm.

• Then slide the lower cable cover onto the monitor arm with the cable

and cord captured.

• Repeat these cable management procedures for the second

monitor arm.

Monitor Arm Adjustments

There are two possible adjustments, both of which are made using the 6mm Allen key.

1. Monitor weight adjustment.

— If the monitor arm is difcult to raise or drifts lower, increase the weight adjustment. Turn the hex nut

counterclockwise.

— If the monitor arm is difcult to lower or drifts higher, decrease the weight adjustment. Turn the hex nut

clockwise.

— After completing the adjustment, the monitor arm should raise and lower easily, and maintain its

position.

2. Monitor tilt adjustment.

— Loosen the nut to make tilting the monitor easier or tighten the nut to hold the tilt position more

securely.

EPPA2-KIT ADJUSTMENTS

1. Monitor Weight

2. Monitor Tilt

Heavier

Monitor

6mm

Allen Key

6mm

Allen Key

Lighter

Monitor

Inhaltsverzeichnis

Andere ESI Rack & Stand Handbücher

ESI

ESI EVOLVE Series Montageanleitung

ESI

ESI Solution 6CC Kurzanleitung

ESI

ESI AA750DAT Bedienungs- und Wartungshandbuch

ESI

ESI LIFT ERGORISE Bedienungsanleitung

ESI

ESI Kata Series Bedienungsanleitung

ESI

ESI Kata EX2-MS Series Bedienungsanleitung

ESI

ESI Kata2-MS Series Bedienungsanleitung

ESI

ESI AA355DS Bedienungsanleitung

ESI

ESI CLIMB2 Bedienungsanleitung

ESI

ESI Kata EX2-FMS Bedienungsanleitung

ESI

ESI E-AMT Bedienungsanleitung

ESI

ESI AA330 Bedienungsanleitung

ESI

ESI AA780DAT Bedienungsanleitung

ESI

ESI LTH-EDGE Bedienungsanleitung

ESI

ESI EVOLVE Series Bedienungsanleitung

ESI

ESI AA100 Kurzanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung