ETC Echoflex Elaho E-LS Bedienungsanleitung

Echoflex Installation Guide

Elaho Light Sensor

Ma in Office Squamish, BC, Canada Phone +1 778 733 0111

Email info@echoflexsolutions.com Web echoflexsolutions.com

Echoflex intends this document to be provided in its entirety.

Product information and specifications subject to change.

8186M2170 Rev C Released 2020-05

Overview

The Elaho Light Sensor provides light level measurement and lighting control

for the connected Elaho control system. The sensor measures lighting

conditions to maintain a programmed lighting output in both dimmed and

switched systems.

Light Sensor Head with Controller

Light Sensor Head

Thread Extender

Light Sensors are available in three models:

•

E-LS - Light Sensor head with controller

•

E-LSC - Light Sensor controller only

•

E-LSH - Light Sensor head only

Each controller supports up to two Light Sensor heads. One head may be

installed within the controller, or both may be installed remotely. When using

a pair of Light Sensor heads, both heads transmit their light readings to a

single Light Sensor controller. The controller averages the received light levels

and uses the average to control the lighting within the space.

Custom Configuration

This document guides you through the installation and local configuration of

the Elaho Light Sensor. For more detailed information about the custom

configuration options available for the Light Sensor using ElahoAccess, see

the ElahoAccess Mobile App integrated help system.

Note:

To use the configuration settings applied using ElahoAccess,

set DIP switch 2 to "On". See DIP Switch Settings on page 9.

Echoflex Installation Guide

Light Sensor

Wire Specification

Controller

The Light Sensor controller utilizes EchoConnect for power and for data

communications with an Elaho control system.

EchoConnect is a bidirectional protocol that uses one pair of wires (data+

and data-) for both data and power. Echoflex recommends using Belden

8471 (or approved equal) Class 2 wire.

The total combined length of an EchoConnect wire run (using Belden 8471,

or equal) may not exceed 500m (1,640ft).

Note:

All control wiring should be installed and terminated by a

qualified installer and should follow standard wiring installation

practices.

Leave approximately 20cm (8in) of wiring in the back box for

connection and to allow slack for future service needs.

Note:

Echoflex requires that all Elaho stations and devices be

grounded for ESDprotection. Pull an additional 2.5 mm2(14AWG)

wire for grounding when control wires are not installed in grounded

metal conduit.

Note:

When using Category 5 (or equivalent) cable on the

EchoConnect communication bus, please note the following:

•

Cat5 wiring must be terminated using EchoConnect Cat5

Termination Kit and must be installed using a bus topology.

Refer to the installation guide that is provided with the Cat5

Termination Kit (8186A1207) for information to terminate

Cat5 wiring.

•

Not all topologies are supported using Cat5; careful planning

is required to ensure the proper termination kits are available

and the wire is pulled appropriately.

Light Sensor Head

The Light Sensor controller provides termination for up to two remote Light

Sensor heads. Each Light Sensor head must be separately wired to the

controller using no more than 304 m (1,000 ft) of 1.5 mm2(16 AWG ) wire

total per controller. These wire runs must remain separate from EchoConnect

wiring. Echoflex recommends using Belden 8471 (or equivalent) wire.

Light Sensor Page 2 of 12 Echoflex

Echoflex Installation Guide

Light Sensor

Installation Environment

You can install the Light Sensor controller to a finished ceiling surface or soft

ceiling tile, or you can attach it to a round junction box or single-gang RACO

junction box. The controller operates in ambient temperatures of 0°C to

70°C, non-condensing humidity.

You can mount the Light Sensor head directly into the controller, to a 1/2”

conduit knockout, or into a soft ceiling tile using the provided thread

extender. Install the Light Sensor head outdoors only when you mount it into

a weatherproof enclosure. The sensor in this weatherproof installation

scenario operates in ambient temperatures of -25°Cto70°C (-13°F to 158°F).

Parts and Supplies

Sensorhead with

controller

(E-LS)

LightSensor

head

(E-LSH)

LightSensor

controller

(E-LSC)

Soft ceiling tile adapter X X

EchoConnect and ground wire

pigtails X X

Light Sensor head thread

extender X X

1 each nuts and washers 3/4"

and 1" X X

2 each screws 6-32 x 3/4" and 6-

32 x 1-3/4" X X

Blank Sensor head X X

Note:

Follow all local code requirements for terminating wire. Use

appropriately sized wire nuts (not provided) to secure each

termination.

Light Sensor Page 3 of 12 Echoflex

Echoflex Installation Guide

Light Sensor

Installation

The Light Sensor controller comes with a twist-lock mounting plate that can

be mounted to a finished ceiling, junction box or soft ceiling tile. Determine

the installation method and follow the specific instructions.

•

Install in Junction Box on page 4

•

Install in Soft Ceiling Tile on page 6

•

Install Sensor Heads Remotely (optional) on page 7

Note:

The EchoConnect pigtail is only required when the sensor and

controller are installed in series with other sensors. If you are not

continuing the data run, we recommend that you terminate directly to

the control board.

Install in Junction Box

Terminate

wires here

Optional

sensor wires

You can terminate the EchoConnect bus and up to two Light Sensor heads at

the controller.

1. Pull Belden 8471 (or equivalent) and 2.5 mm2(14 AWG) ground wire

to the junction box.

Light Sensor Page 4 of 12 Echoflex

Echoflex Installation Guide

Light Sensor

2. If you are installing the controller in series (continuing the data run) to

other sensors, sensor controllers, or stations, use the provided

EchoConnect pigtail and ESD ground pigtail to make the terminations.

If you are not continuing the data run, proceed to Step 3.

a. Strip each wire to the appropriate length, depending on the wire

nut or other termination used (wire nuts are not provided).

b. Twist the data - (typically black) EchoConnect wire, the black lead

from the EchoConnect pigtail, and any continuing EchoConnect

(typically black) wire together and secure with the wire nut.

c. Repeat the above steps for the data + (typically white)

EchoConnect wires, and for the ESD ground wires.

Note:

Sensor wires must terminate directly to the terminals located

on the controller.

3. If you are installing the primary and/or optional second Sensor head

external from the controller, also known as remoting the Sensor head,

see

Install Sensor Heads Remotely (optional) on page7

, and then

return to these instructions. If you are not remoting the Sensor head,

proceed to Step 4.

4. Orient the smooth side of the mounting plate to the junction box. Pull

the following wires from the junction box through the provided holes

of the mounting plate:

•

EchoConnect bus wires and ESD ground wires

•

Light Sensor head wires (if installed)

5. Secure the mounting plate to the junction box using the screws

provided.

6. Strip each wire 8 mm (5/16 in) and terminate the EchoConnect (white

and black wires) and ground wire (green/yellow) to the EchoConnect

terminal block located on the controller. Torque each termination to

3.1-3.5 in-lb.

a. Terminate the incoming data + (typically white) wire to the data+

terminal.

b. Terminate the incoming data - (typically black) wire to the data-

terminal.

c. Terminate the incoming ground (typically green/yellow) wire to

the labeled ground terminal.

7. To terminate remote Light Sensor heads, see

Install Sensor Heads

Remotely (optional) on page7

Light Sensor Page 5 of 12 Echoflex

Echoflex Installation Guide

Light Sensor

Install in Soft Ceiling Tile

Poke the adapter through the ceiling tile, then bend

it over for a secure fit.

EchoConnect pigtail

and connectors

(optional use)

Terminate

wires here

Optional

sensor wires

soft ceiling

tile adapter

1. Pull the Belden 8471 (or equivalent) and 2.5 mm2(14 AWG) ground

wire to the installation location.

2. If you are installing the sensor in series (continuing the data run) to

other sensors, sensor controllers, or stations, use the provided

EchoConnect pigtail and ESD ground pigtail to make the terminations.

If you are not continuing the data run, proceed to Step 3.

a. Strip each wire to the appropriate length, depending on the wire

nut or other termination used (wire nuts are not provided).

b. Twist the data - (typically black) EchoConnect wire, the black lead

from the EchoConnect pigtail, and any continuing EchoConnect

(typically black) wire together and secure with the wire nut.

c. Repeat the above steps for the data + (typically white)

EchoConnect wires, and for the ESD ground wires.

Note:

Sensor wires must terminate directly to the terminals located

on the controller.

3. If you are installing the primary and/or optional (second) Light Sensor

head remotely from the controller, see

Install Sensor Heads Remotely

(optional) on page 7

, and then return to these instructions. If you are

not remoting a Light Sensor head, proceed to Step 4.

4. Create a hole for wire pass-through in the ceiling tile by poking

through the center hole or oblong hole of the mounting plate, and

then pull the wires through.

Light Sensor Page 6 of 12 Echoflex

Echoflex Installation Guide

Light Sensor

5. Orient the smooth side of the mounting plate to the ceiling tile. Pull

the following wires from the junction box through the provided holes

of the mounting plate:

a. EchoConnect bus wires and ESD ground wires

b. Light Sensor head wires (if installed )

6. Align and insert the soft ceiling tile adapter through the holes

provided on the mounting plate, poke the tines of the adapter

through the ceiling tile, and then bend each tine over in opposite

directions for a secure fit on the back side of the ceiling tile.

7. Strip each wire 8 mm (5/16 in) and terminate the EchoConnect (white

and black wires) and ground wire (green/yellow) to the EchoConnect

terminal block located on the sensor controller. Torque each

terminationto3.1-3.5in-lb.

a. Terminate the incoming data + (typically white) wire to the

data+terminal.

b. Terminate the incoming data - (typically black) wire to the

data-terminal.

c. Terminate the incoming ground (typically green/yellow) wire to

the labeled ground terminal.

Install Sensor Heads Remotely (optional)

Installed with

thread extender

Installed without extender

Each Light Sensor head must be

separately wired to the controller

using no more than 1,000 feet

(304 m) of 1.5mm2(16AWG)

wire total per controller.

These wire runs must remain

separate from EchoConnect

wiring. Echoflex recommends

using Belden 8471 (or

equivalent) wire.

1. Prepare a hole in the installation location (3/4” hole without adapter

or 1” with adapter).

2. Run Belden 8471 (or equivalent) between the controller and the Light

Sensor head installation location.

3. For a soft ceiling tile installation, pull the Sensor head wire leads

through the thread extender, and then attach the thread extender

onto the head.

4. Insert the head wires through the finished side of the installation

location to the unfinished side (ceiling).

Light Sensor Page 7 of 12 Echoflex

Echoflex Installation Guide

Light Sensor

5. Thread the appropriate washer and nut (two sizes included) onto

either the head or the extension adapter (if used), securing it in place.

Terminate Sensor Head Control Wiring

1. Terminate the incoming wire from the controller to the head leads

using wire nuts or other wire termination (not provided).

a. Strip each wire to the appropriate length, depending on the wire

nut or other wire termination used (wire nuts are not provided).

b. Twist the installed (typically black) Belden 8471 incoming wire

and the black lead from the head together and secure using a

wire nut or other wire termination.

c. Repeat for the installed (typically white) Belden 8471 wire and

remaining wire lead.

2. Terminate the incoming wire pairs from the remote Light Sensor head

to the controller.

a. At the controller, strip 9-10 mm (5/8 in) of insulation from the

ends of each installed head wire.

b. Using a small 3.35 mm (1/8 in) flat blade or #1 Phillips

screwdriver, loosen the terminals on the “Primary Sensor” and

“Optional Sensor” connectors found on the Light Sensor

controller.

c. Insert the black (typical) wire from the first Light Sensor head wire

pair into terminal “1” of the “Primary Sensor” connector.

d. Insert the white (typical) wire from the first Light Sensor head wire

pair into terminal “2” of the “Primary Sensor” connector.

e. Repeat this process for the second wire pair, if installed, to the

“Optional Sensor” connector.

Sensor Configuration

The Elaho Light Sensor participates in an Elaho

system using the configured Space and Address,

which you set using the rotary switches on the rear

panel of the sensor.

Additional DIP switches and the [MODE] button,

also located on the rear panel, set the sensor

functionality and the sensor function with

dark

and

bright

actions.

Light Sensor Page 8 of 12 Echoflex

Echoflex Installation Guide

Light Sensor

Set Space and Address

Use the two rotary switches on the rear panel of the controller to set the

sensor Space and Address. By default, these switches are set to

Space1,Address1.

Note:

Do not duplicate a device Address within the same Space.

Commands are shared by all devices within a space.

DIP Switch Settings

Use the DIP switches on the rear panel of the Light Sensor controller to set

additional configuration options including deadband sensitivity, delay time,

and to restore the sensor to its factory defaults.

DIP Switch 1

DIP switch position 1 determines whether the sensor will use a Dimming

operation (Off) or a Switched operation (On). The default setting is Dimming

operation. See

Sensor Operation on page11

DIP Switch 2

DIP switch 2 enables “Custom Config”, which instructs the sensor to use

settings that are configured using the ElahoAccess Mobile App. This setting is

“Off” by default.

•

When “Custom Config” is set to “Off” (default setting), the controller

uses the local DIP switch settings for the

dark

and

bright

actions. You

can adjust sensor actions using the program [MODE] button.

•

When “Custom Config” is set to “On”, the controller ignores local

DIP switch settings. Instead, the controller uses Delay Time, Deadband

Sensitivity, Switched or Dimming operation setting,

dark

bright

event settings, and Dimming Raise and Lower Event settings that you

set in the ElahoAccess Mobile App.

DIP Switch 3&4

DIP switches 3 & 4 set the “Delay Time”. Supported times are in minutes.

•

5 minutes = Switches 3 and 4 "Off" (default setting)

•

15 minutes = Switch 3 "Off"and 4 "On"

•

30 minutes = Switch 3 "On"and 4 "Off"

•

60 minutes = Switches 3 and 4 "On"

Light Sensor Page 9 of 12 Echoflex

Echoflex Installation Guide

Light Sensor

DIP Switch 5&6

DIP switches 5 & 6 set the deadband sensitivity, which corresponds to 10%,

20%, 35%, and 50% as a percentage of the Target Lux. The low measured

light threshold is Target - (Target x Deadband%) / 100. See

Attach Sensor on

the facing page

. The high measured light threshold is Target + (Target x

Deadband%) / 100.

•

10 % = Switches 5 and 6 "Off" (default setting)

•

20 % = Switch 5 "Off"and 6 "On"

•

35 % = Switch 5 "On"and 6 "Off"

•

60 % = Switches 5 and 6 "On"

DIP Switch 7

DIP switch 7 is not used in this product.

DIP Switch 8

DIP switch 8 provides a “restore defaults at boot” function. To restore the

factory defaults, set this DIP switch to “On” and then cycle power to the

sensor.

Power Up and Final Installation

Complete all EchoConnect terminations in the system before you apply power

to the system and sensor.

Sensor Count

The controller includes an LED labeled “Mode/Sensor Count” that blinks

green according to the number of Sensor heads connected to the controller.

Check this LED to ensure that the system has been wired properly and that

the controller has detected the number of connected remote heads. If the

Mode/Sensor Count LED is solid red, the controller does not detect any

sensors. Check your system wiring first, and then contact Echoflex Technical

Services if additional troubleshooting assistance is required.

Configure Preset

Mode button

Mode/Sensor Count LED

When in Basic config mode (DIP switch 2

is set to "Off"), holding the [MODE]

button sets the sensor into program

mode. Program mode only affects

switched operation and is used to adjust

the preset controlled by the

dark

action

when measured light levels are below

the target threshold setting. The

bright

action is “Off,” and occurs when measured light levels are above the target

threshold. This is not configurable through Program mode.

Light Sensor Page 10 of 12 Echoflex

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETC Zubehör Handbücher

ETC

ETC Sasquatch Bedienungsanleitung

ETC

ETC Sohrana Dual Tech Bedienungsanleitung

ETC

ETC Echoflex Elaho Bedienungsanleitung

ETC

ETC echoflex MOS-MT Series Bedienungsanleitung

ETC

ETC Unison Heritage Bedienungsanleitung

ETC

ETC Echo Dual Tech Wall-mount Vacancy Sensor Bedienungsanleitung

ETC

ETC Unison Aero SimpleTap Cubicle Station Bedienungsanleitung

ETC

ETC echoflex RCT Bedienungsanleitung

ETC

ETC echoflex OWS-IR-UW-120/277 Bedienungsanleitung

ETC

ETC echoflex MOS-IR A Series Bedienungsanleitung

ETC

ETC P-OCC-SR Bedienungsanleitung

ETC

ETC Echoflex Bedienungsanleitung

ETC

ETC Echoflex Elaho Bedienungsanleitung

ETC

ETC Unison Echo Dual Tech Switch-mount Occupancy... Bedienungsanleitung

ETC

ETC Echoflex Dual Tech Bedienungsanleitung

ETC

ETC Unison Aero Bedienungsanleitung

ETC

ETC Unison Aero Bedienungsanleitung

ETC

ETC Echo Dual Tech Ceiling-mount Vacancy Sensor Bedienungsanleitung

ETC

ETC Echoflex Elaho Bedienungsanleitung

ETC

ETC SR12D Bedienungsanleitung

ETC

ETC Echoflex UWLDU-3 Bedienungsanleitung

ETC

ETC E-DOC-C-LR Bedienungsanleitung

ETC

ETC Aero SimpleTap Occupancy Sensor Bedienungsanleitung

ETC

ETC Unison Echo E-OCC-SR Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

ETC echoflex Elaho E-LS Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken