ETC F-Drive W1 Series Bedienungsanleitung

F-Drive Series W1

Installation Manual

Part Number: 7148M2110 Rev: D

Released: 2022-01

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked

and not marked, are the property of their respective owners.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents

Table of Contents i

Introduction 1

Compatible Products 1

F-Drive System Design Tool 1

LEDDimming Compatibility Database 1

Documentation for Compatible Products 1

Document Conventions 2

Help from ETC Technical Services 3

Safety 4

IMPORTANTSAFEGUARDS 4

Label Symbols 4

Chapter 1 Overview 5

Features 5

W1 Models 6

Third-Party Fixtures 7

Emergency System Overview 7

W1 Emergency Functionality 7

Before You Begin Installation 9

Installation Requirements 9

Power Disconnect Device 9

Chapter 2 W1 Installation 10

Prepare to Install the W1 10

Parts and Tools 10

Mounting Straps 10

Electrical and Wiring Specifications 12

Install the W1 13

Wall-Mount the W1 Driver 14

Connect the Power Input 15

DMXIn and Thru Connections 17

Terminate DMXIn and DMXThru 18

Connect Luminaires to Outputs 19

Chapter 3 W1 Emergency Driver Installation 23

Wire a W1 Emergency Driver 23

Connect the Sense Input 25

Connect the Maintain Input 25

Configure the W1 CC Emergency Driver TEST Button for

Low-Voltage Loads 26

Complete the Installation 26

Chapter 4 Power Up and Control 27

Power Up Procedure 27

Identify 27

DMX System Control 27

Navis Luminaire DMXPersonalities 28

RDM Parameters 29

On Below Minimum 31

Live Edit Configuration Files 32

Edit Offline and Save Configuration Files to MicroSD32

Firmware Upgrade Instructions 33

MicroSD Firmware Upgrade Instructions 33

Maintenance 34

Emergency Operation and Test 34

Troubleshooting 35

Test Button 35

LEDIndicators 35

Appendix A Compliance 36

FCC Compliance 36

ii W1 Installation Manual

Introduction

Congratulations on your purchase of the ETC F-Drive Series W1. The F-Drive Series W1 Driver

LEDpower control solutionprovides a centralized approach for controlling LEDluminaires. It is a

wall-mount driver that provides power and data for up to four circuits in standard and

emergency installations. By maintaining remote, easy access to the driver, LED-based systems

can be easily installed and serviced, while ensuring critical components are readily accessible to

support staff.

Compatible Products

R12 output cards are compatible with Navis100 Fixed White, Fade to Warm, and RGBW

luminaires; ArcSystem Pro One-Cell, Pro One-Cell Small, and Pro One-Cell Micro luminaires;

ArcSystem ArcLamps; and a variety of constant current and constant voltage luminaires. For

more information on compatible products, see the resources below.

W1 Drivers are compatible with Navis100 Fixed White, Fade to Warm, and RGBW luminaires;

ArcSystem Pro One-Cell Pro One-Cell Small, and Pro One-Cell Micro luminaires; and a variety

of constant current and constant voltage luminaires. For more information on compatible

products, see the resources below.

F-Drive System Design Tool

The F-Drive System Design Tool (etcconnect.com/Products/Power-Controls/LED-Drivers/F-

Drive/F-Drive-System-Design-Tool.aspx) allows you to design an F-Drive R12 rack unit or F-Drive

W1 driver with different luminaires, breakout boxes, cable lengths, and other system

components.

LEDDimming Compatibility Database

The LEDDimming Compatibility Database (etcconnect.com/compatibility/) is a searchable list of

devices that ETChas tested for compatibility with ETCdimming and control systems.

Documentation for Compatible Products

The following documents are available at etcconnect.com/Products/Power-Controls/LED-

Drivers/F-Drive/Documentation.aspx:

•

F-Drive B-Box4 Installation Guide

•

F-Drive S-Box Installation Guide

•

F-Drive Series W1 Installation Manual

•

F-Drive R12 and W1 Wiring Reference Guide

The following document is available at etcconnect.com/Products/Lighting-Fixtures/ArcSystem-

Navis/Documentation.aspx:

•

ArcSystem Navis 100 Installation Guide

The following document is available at etcconnect.com/Products/Lighting-Fixtures/Pro-One-

Cell/Documentation.aspx:

•

ArcSystem Pro D1 and D2 Series Drivers Installation Guide

The following document is available at etcconnect.com/Products/Lighting-

Fixtures/ArcLamp/Documentation.aspx

•

ArcLamp System Installation Manual

2 W1 Installation Manual

Document Conventions

This document uses the following conventions to draw your attention to important information.

Note:

Notes are helpful hints and information that is supplemental to the main text.

CAUTION:

A Caution statement indicates situations where there may be

undefined or unwanted consequences of an action, potential for data loss or

an equipment problem.

WARNING: A Warning statement indicates situations where damage may

occur, people may be harmed, or there are serious or dangerous

consequences of an action.

WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates

situations where there is a risk of electric shock.

All ETC documents are available for free download from our website: etcconnect.com.

Please email comments about this manual to: TechComm@etcconnect.com.

Help from ETC Technical Services

If you are having difficulties and your problem is not addressed by this document, try the ETC

support website at support.etcconnect.com or the main ETC website at etcconnect.com. If none

of these resources are sufficient, contact ETC Technical Services directly at one of the offices

identified below. Emergency service is available from all ETC offices outside of normal business

hours.

When calling for help, take these steps first:

•

Prepare a detailed description of the problem

•

Go near the equipment for troubleshooting

•

Find your notification number if you have called in previously

ETC, Inc.

Americas

Technical Services Department

3031 Pleasant View Road

Middleton, WI 53562

800-775-4382 (USA, toll-free)

+1-608 831-4116

service@etcconnect.com

ETC GmbH

Germany, Austria, Switzerland,

Eastern Europe, and Russia

Technical Services Department

Ohmstrasse 3

83607 Holzkirchen, Germany

+49 (80 24) 47 00-0

techserv-germany@etcconnect.com

ETC Austin

High End Systems Products

Technical Services Department

2105 Gracy Farms Lane

Austin, TX 78758 USA

800-890-8989 (USA, toll-free)

+1-512 836-2242

hesservice@etcconnect.com

ETC France

France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

techservfrance@etcconnect.com

ETC Ltd

Europe, Middle East, and Africa

Technical Services Department

26-28 Victoria Industrial Estate

Victoria Road,

London W3 6UU England

+44 (0)20 8896 1000

techservltd@etcconnect.com

ETCAsia

Asia

Technical Services Department

Room 1801, 18/F

Tower 1, Phase 1 Enterprise Square

9 Sheung Yuet Road

Kowloon Bay, Kowloon, Hong Kong

+852 2799 1220

techserv-asia@etcconnect.com

4 W1 Installation Manual

Safety

The F-Drive Series W1 is intended for professional use only. Read the entire manual before

using this equipment.

IMPORTANTSAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed

including the following:

•

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS.

•

Do not use outdoors.

•

Do not let power supply cords touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should be mounted in locations and at heights where it will not

readily be subjected to tampering by unauthorized personnel.

•

The use of accessory equipment not recommended by the manufacturer may

cause an unsafe condition.

•

Do not use this equipment for other than intended use.

•

To reduce the risk of fire and overheating, make sure all connections are tight.

•

Turn off electrical power before modifying the lighting system in any way.

SAVE THESE INSTRUCTIONS

Label Symbols

The W1 Series are conveniently labeled with relevant symbols for your safety. Refer to the

product label to see which symbols apply to your product.

General warning Avertissement général

This product should not be discarded as unsorted

waste but must be sent to separate collection

facilities for recovery and recycling.

Ce produit ne doit pas être jeté avec les déchets

ménagers mais doit être déposé dans une collecte de

déchets électroniques ou dans un point de collecte.

The product input or output is suitable for direct

current only.

L’entrée et la sortie de ce produit convient

uniquement au courant continu.

The product input or output is suitable for

alternating current only.

L’entrée et la sortie de ce produit convient

uniquement au courant alternatif.

Safety extra low voltage device Dispositif de sécurité à très basse tension

Independent lighting control gear Appareil de contrôle d’éclairage indépendant.

Emergency lighting driver (non-battery powered)

according to EN-61347-2-13.

Pilote d’éclairage d’urgence (pas alimenté par piles)

conformément à la norme EN-61347-2-13.

Protective earth (ground) Protection Classe I Mise à la terre

tcor TcRated maximum case temperature Température maximale recommandée pour le boîtier

Chapter 1 5

Chapter 1

Overview

F-Drive W1 and W1E Drivers

Features

•

Compatible with a wide range of control systems

•

DMX/RDM control input with per-circuit patching

•

W1E models are UL 924 and CSA C22.2 No. 141 listed for emergency lighting control

WARNING: Connect this equipment to a non-dimmable power source in

order to avoid damage to the equipment's internal power supply and other

electrical components. Using a dimmable power source may damage the

equipment and will void the warranty.

6 W1 Installation Manual

W1 Models

Variant Load Type Output Type Output

Voltage

Per

Circuit

Limits

Driver

Limits

Output

Connectors

W1 Fade to Warm

Driver

FDW1FTWD (-CE) up to four total

ETCArcSystem Navis

100 Fade to Warm

luminaires

constant

current,

maximum

450mA per

channel

48VDC 450mA,

21.6W

1.8A,

86W

RJ45 and 4

two-pin

terminal

blocks

W1 Fade to Warm

Emergency Driver

FDW1EFTWD (-

CE)

W1 CC Driver

FDW1CCD (-CE)

•

up to four total ETC

ArcSystem Navis 100

Fixed White

luminaires

•

up to four total

ETCArcSystem Pro

One-Cell White or

Fade to Warm

luminaires

Pro One-Cell

Pro One-Cell Small

Pro One-Cell Micro

•

200–700 mA fixtures

manufactured by

others

constant

current,

adjustable from

200–700mA,

default output

600mA (see

Configure the

W1 CC Driver

on page22

)

48VDC 700mA,

33W

2.8A,

134W

RJ45 and 4

two-pin

terminal

blocks

W1 CC Emergency

Driver

FDW1ECCD (-CE)

W1 CV Driver

Constant Voltage

FDW1CVD (-CE)

multiple 24VDC fixtures 24VDC 24VDC 2.1A,

50W

6.25A,

150W

4 two-pin

terminal

blocks

W1 CV Emergency

Driver Constant

Voltage

FDW1ECVD (-CE)

W1 Chroma Driver

FDW1CHD (-CE)

up to four total

ETCArcSystem Navis

100 RGBW luminaires

48 VDCpower

and data 48VDC 2.1A,

100W RJ45

Note:

Use ONEtype of output connector. For example, use the RJ45 receptacle OR

the two-pin terminal blocks on a W1 Fade to Warm Driver or a W1 CC Driver.

Note:

F-Drive W1 Drivers do not support ArcSystem Pro One-Cell High Output

luminaires.

Andere Handbücher für F-Drive W1 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC Echo Bedienungsanleitung

ETC

ETC ColorSource Spot Bedienungsanleitung

ETC

ETC ColorSource Raceway Bedienungsanleitung

ETC

ETC Source Four jr Bedienungsanleitung

ETC

ETC microVision FX Bedienungsanleitung

ETC

ETC ColorSource PAR Bedienungsanleitung

ETC

ETC IRIDEON AR500 Bedienungsanleitung

ETC

ETC Source 4WRD Bedienungsanleitung

ETC

ETC Source Four Mini LED Bedienungsanleitung

ETC

ETC ColorSource CYC Bedienungsanleitung

ETC

ETC Source Four Revolution Scroller Cartridge Bedienungsanleitung

ETC

ETC Halcyon Gold Bedienungsanleitung

ETC

ETC Hog 4 Series Bedienungsanleitung

ETC

ETC SolarFrame 750 Bedienungsanleitung

ETC

ETC High End Systems SolaPix 7 Bedienungsanleitung

ETC

ETC Lustr+ Bedienungsanleitung

ETC

ETC GDS BluesSystem Bedienungsanleitung

ETC

ETC Express 24/48 Bedienungsanleitung

ETC

ETC Source Four Revolution Scroller Cartridge Bedienungsanleitung

ETC

ETC Source 4WRD II Bedienungsanleitung

ETC

ETC Sensor IQ DALI Control Option Card Bedienungsanleitung

ETC

ETC fos/4 Panel Yoke Bedienungsanleitung

ETC

ETC Source Four LED Series Installationsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung