ETC Fos/4 Series Bedienungsanleitung

fos/4 Panel

User Manual

Version 1.0.0

Part Number: 7471M1200-1.0.0 Rev: A

Released: 2020-01

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked

and not marked, are the property of their respective owners.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents

Table of Contents i

Introduction 1

Help from ETC Technical Services 2

Safety 3

Overview 5

Fixture 5

User Interface 6

Set Up and Focus the Fixture 7

Mount the Fixture 7

Add Accessories 8

Connect Power and Data 8

Focus the Fixture 9

Use Fixture in DMX Mode 10

Set DMXAddress 10

Set DMXMode 10

Set DMX Loss Behavior 12

Use Fixture in Stand-aloneMode 13

Studio Mode 14

Color Mode 15

Effects Mode 16

Preset Mode 17

Set Up Wireless Control 18

Set Up Multiverse Wireless Communication 18

Control Fixtures Wirelessly Using the Set LightApp 18

Control and Customize the Display 19

Lock the Display 19

Adjust the Display Backlight and Display Timeout 19

Troubleshooting and Maintenance 20

Troubleshooting Checklist 20

Test the Emitters 22

View Diagnostic Data 22

View Battery Level 23

Export Fixture Data for Troubleshooting 23

Restore Default Settings 24

Update Firmware 24

Backup and Restore the Fixture Configuration 25

Clean the Diffusion 25

Specifications and Reference 26

Environment 26

Dimensions and Weight 26

Electrical 27

RDM Parameters 27

Fixture Compliance 28

Wireless Radio Compliance 28

ii fos/4 Panel User Manual

Introduction 1

Introduction

The fos/4 Panel provides an incredibly bright, top quality, highly tunable light. The Panel is

available in three sizes, and each size is available in two array types:

•

Lustr X8: The next generation of the Lustr color system incorporates deep red into the

already amazing x7 mix to create an even more rich, vibrant X8 color palette.

•

Daylight HDR: Years of research resulted in an LED mix that yields the highest quality

tunable white light, optimized for studio use.

Model Array Type Array Size Weight

fos4PL8 Lustr X8

20.3 x 61 cm (8x 24in) 14.5 kg (32 lb)

fos4PD8 Daylight HDR

fos4PL16 Lustr X8

40.6 x 61 cm (16 x 24in) 25.4 kg (56 lb)

fos4PD16 Daylight HDR

fos4PL24 Lustr X8

61 x 61 cm (24 x 24in) 35.8 kg (79 lb)

fos4PD24 Daylight HDR

2 fos/4 Panel User Manual

Help from ETC Technical Services

If you are having difficulties and your problem is not addressed by this document, try the ETC

support website at support.etcconnect.com or the main ETC website at etcconnect.com. If none

of these resources are sufficient, contact ETC Technical Services directly at one of the offices

identified below. Emergency service is available from all ETC offices outside of normal business

hours.

When calling for help, take these steps first:

•

Prepare a detailed description of the problem

•

Go near the equipment for troubleshooting

•

Find your notification number if you have called in previously

Americas United Kingdom

ETC, Inc. ETC Ltd

Technical Services Department Technical Services Department

3031 Pleasant View Road 26-28 Victoria Industrial Estate

Middleton, WI 53562 Victoria Road,

800-775-4382 (USA, toll-free) London W3 6UU England

+1-608 831-4116 +44 (0)20 8896 1000

service@etcconnect.com techservltd@etcconnect.com

Asia Germany

ETCAsia ETC GmbH

Technical Services Department Technical Services Department

Room 1801, 18/F Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square 83607 Holzkirchen, Germany

9 Sheung Yuet Road +49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong techserv-hoki@etcconnect.com

+852 2799 1220

techservasia@etcconnect.com

France

ETC France

62-64 rue Danielle

Casanova

Saint-Denis Cedex,

F93200

+33 1 4243 3535

techservltd@etcconnect.com

Introduction 3

Safety

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including

the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

•

Do not use outdoors.

•

Do not let power supply cords touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should be mounted in locations and at heights where it will not readily be

subjected to tampering by unauthorized personnel.

•

The use of accessory equipment not recommended by the manufacturer may cause an

unsafe condition.

•

Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS

WARNING: Note the following safety warnings before use:

•

Use the fixture in dry locations only, where humidity does not exceed

90 percent (non-condensing).

•

Connect the fixture to a non-dimmable power source in order to avoid

damage to the fixture's internal power supply and other electrical

components. Using a dimmable power source can damage the fixture

and will void the warranty.

WARNING: Note the following safety warnings before use:

•

Disconnect the fixture from power and DMX and allow it to cool before

installing accessories or performing any cleaning and maintenance.

•

Only use mounting hardware that is rated for the total weight of the

fixture and accessories.

•

In addition to primary suspension, attach a safety cable (or other

approved safety device) to the fixture. Safety cables must be rated to

support six times the fixture weight. See

Mount the Fixture on page7

•

Check that the accessory holder is locked and that any accessory safety

cables are connected before mounting the fixture.

•

Do not mount the fixture on or near a flammable surface.

•

Do not operate the fixture without the diffusion installed.

•

Do not use this fixture with a damaged power lead. If the power lead

(cord set) is damaged, it must be replaced.

•

Do not use this fixture if the diffusion is deeply scratched or cracked.

You must replace the diffusion when it is damaged.

4 fos/4 Panel User Manual

AVERTISSEMENT : Prendre connaissance des avertissements de sécurité

suivants avant toute utilisation :

•

Débranchez le projecteur de son alimentation et du DMX et laissez-le

refroidir avant d’installer des accessoires ou d’effectuer un nettoyage

ou un entretien.

•

N’utilisez que de la quincaillerie de montage adaptée au poids total

des projecteurs et des accessoires.

•

En plus de la suspension principale, fixez une chaîne de sécurité (ou

tout autre dispositif de sécurité homologué) au projecteur. Les chaînes

de sécurité doivent être en mesure de supporter six fois le poids du

projecteur.

•

Vérifiez que le porte-accessoires est verrouillé et que les élingues de

tous les accessoires sont bien attachées avant de monter le projecteur.

•

Ne pas installer le projecteur sur ou à côté d’une surface inflammable.

•

N’utilisez pas le projecteur sans que le diffuseur soit installé.

•

Ne pas utiliser ce projecteur avec un cordon d’alimentation

endommagé. Si le cordon d’alimentation (câble) est abîmé, il doit être

remplacé.

•

N’utilisez pas ce projecteur si le diffuseur présente des rayures ou des

fissures profondes. Il faut remplacer le diffuseur s'il est abîmé.

Overview 5

Overview

Fixture

Medium

(PL16 or PD16)

Small

(PL8 or PD8)

Large

(PL24 or PD24)

AAccessory holder: Insert accessories into the two available slots from either side of the holder,

and then lock the holder (

page8

BHandles: For medium (PL16 or PD16) and large (PL24 or PD24) fixtures, carry the fixture by the

pairs of handles on the back of the fixture, and attach safety cables to handles when mounting

the fixture (

page7

CYoke tilt-lock: Tilt the fixture as needed, and then turn the tilt-lock clockwise to lock the

position. If necessary, press the center button on the tilt-lock to adjust the tilt-lock position.

DBattery connector: Four-pin XLRconnector for battery power (not available on PL24 or PD24).

Connect the fixture to battery power only when AC power is not available. Do not connect the

fixture to a battery and to AC power at the same time.

EPower In and Power Thru connectors: powerCON®TRUE1 TOP connectors for power in and

power thru. The large fixture (PL24 or PD24) has a connector for power in only (no power thru

connector).

FUser interface: View the fixture status, set the DMXaddress and mode, or set stand-alone

options.

GDMX In and DMX Thru connectors: Five-pin XLRconnectors for DMX/RDM in and

DMX/RDMthru.

HGriprail: Attach standard accessories and mounting hardware to the back of the fixture using

the hardware provided with the accessories or using M6 standard T-nuts.

ISafety cable attachment points: Small (PL8 or PD8) fixture only. For large and medium

fixtures, attach safety cables to handles (B), either the top pair or the bottom pair (

page7

6 fos/4 Panel User Manual

User Interface

Effects

Effect Flicker

Rate 200

Min 0%

Max Int 100%

DMX

ADisplay: The colors of options on the display correspond to the colors of the encoders below the

display (F) and the Intensity encoder to the right of the display(B).

BIntensity encoder:

•

When in DMX mode, press the Intensity encoder to enter Focus mode when focusing the

fixture.

•

When configuring the fixture in one of the stand-alone modes, press the Intensity encoder to

toggle between the current intensity and 0, or turn the Intensity encoder to modify the white

fields on the display. See

Use Fixture in Stand-aloneMode on page13

•

When navigating from the Main Menu screen, turn the Intensity encoder to scroll through

menu options, and then press the Intensity encoder to select a menu option.

CMenu button: Press to view the Main Menu screen and configure the fixture. Press the button

again to return to the previous screen when you are setting configuration options.

DFunction button: Press repeatedly to toggle through the following modes:

•

Studio: Use one of three studio (white light) presets, or customize the presets.

•

Color: Use one of 12 color presets, or customize the presets.

•

Preset: Use one of 12 presets (color preset + fade time), or customize the presets.

•

Effects: Use one of 12 effects, or customize the effects.

•

DMX: View and set DMX parameters for the fixture.

See

Use Fixture in Stand-aloneMode on page13

and

Use Fixture in DMX Mode on page10

EAntenna: For use when controlling the fixture using wireless DMX (

page18

FEncoders(Red, Green, Blue):The colors of encoders correspond to options on the display.

Press to activate the options at the bottom of the display, or turn to modify the values on the

display.

GNFC(Near Field Communication) tag: Use the Set Light app to wirelessly configure the fixture,

with or without power applied to the fixture (

page18

HUSB port: Use for updating firmware, saving and loading fixture configuration settings, or

saving error logs via a flash drive. See

Troubleshooting and Maintenance on page20

IUI lock: Set this switch to lock the UI. This prevents inadvertent changes to the UI. See

Lock the

Display on page19

Andere Handbücher für fos/4 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC Sensor IQ DALI Control Option Card Bedienungsanleitung

ETC

ETC High End Systems SolaFrame 3000 Bedienungsanleitung

ETC

ETC HIGH END SYSTEMS LONESTAR Bedienungsanleitung

ETC

ETC High End Systems SolaPix 7 Bedienungsanleitung

ETC

ETC Lustr+ Bedienungsanleitung

ETC

ETC Desire D40XTI Bedienungsanleitung

ETC

ETC fos/4 Panel Yoke Bedienungsanleitung

ETC

ETC ELTS2 Bedienungsanleitung

ETC

ETC Desire D60 XTI Bedienungsanleitung

ETC

ETC fos/4 Panel Pole-Operated Yoke Bedienungsanleitung

ETC

ETC Desire Fresnel Bedienungsanleitung

ETC

ETC ColorSource Spot Bedienungsanleitung

ETC

ETC fos/4 Panel Yoke Bedienungsanleitung

ETC

ETC Source Four jr Bedienungsanleitung

ETC

ETC Irideon WLZ Bedienungsanleitung

ETC

ETC Prodigy FlyPipe Studio Bedienungsanleitung

ETC

ETC ColorSource PAR Bedienungsanleitung

ETC

ETC XDLT Bedienungsanleitung

ETC

ETC Lighting Control Console Bedienungsanleitung

ETC

ETC F-Drive W1 Series Bedienungsanleitung

ETC

ETC Source Four Mini LED Bedienungsanleitung

ETC

ETC Source Four MultiPAR Bedienungsanleitung

ETC

ETC Source Four Mini CE Bedienungsanleitung

ETC

ETC Source Four Revolution Scroller Cartridge Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

ETC fos/4 Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken