ETC Fos/4 Fresnel Bedienungsanleitung

ETC Quick Guide

fos/4 Fresnel

Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000

Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535

Web etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETCintends this document to be provided in its entirety.

7470M1300-1.1.1 Rev A Released 2020-10

Overview

Use the images below as a guide to connect power and data and to navigate the basic features of

the fixture. For complete information, see the

fos/4 Fresnel User Manual

at etcconnect.com.

AAccessory holder: Insert accessories into the two available slots from either side of the holder, and

then lock the holder. See

Add Accessories on page4

BYoke tilt-lock: Tilt the fixture as needed, and then turn the tilt-lock clockwise to lock the position. If

necessary, press the center button on the tilt-lock to adjust the tilt-lock position.

CAdjustable yoke: Loosen the bolts, and then shift the adjustable yoke forward or backward as

needed to balance the fixture. Tighten the bolts to secure. See

Add Accessories on page4

DZoom knob: Rotate the zoom knob on either side of the fixture to adjust from spot to flood.

ENFC(Near Field Communication) tag: Use the Set Light app to wirelessly configure the fixture, with

or without power applied to the fixture.

FUser interface: View the fixture status, set the DMXaddress and mode, or set stand-alone options.

GAntenna: For use when controlling the fixture using wireless DMX.

HSafety cable attachment point: See

Mounting and Safety Cables on page4

IDMX In and DMX Thru connectors: Five-pin XLRconnectors for DMX/RDM in and thru.

JPower In and Power Thru connectors: powerCON®TRUE1 TOP connectors for power in and power

thru.

KBattery connector: Three-pin XLRconnector for battery power. Connect the fixture to battery power

only when AC power is not available. Maximum fixture output may be reduced when powered by

battery.

ETC Quick Guide

fos/4 Fresnel

fos/4 Fresnel Page 2 of 8 ETC

User Interface

Effects

Effect Flicker

Rate 200

Min 0%

Max Int 100%

DMX

ADisplay: The colors of options on the display correspond to the colors of the encoders below the

display (E) and the Intensity encoder to the right of the display(B).

B Intensity encoder:

•

When in DMX mode, press the Intensity encoder to enter Focus mode when focusing the fixture.

•

When configuring the fixture in one of the stand-alone modes, press the Intensity encoder to

toggle between the current intensity and 0, or turn the Intensity encoder to modify the white

fields on the display. See

Use Fixture in Stand-aloneMode on page7

•

When navigating from the Main Menu screen, turn the Intensity encoder to scroll through menu

options, and then press the Intensity encoder to select a menu option.

CMenu button: Press to view the Main Menu screen and configure the fixture. Press the button again

to return to the previous screen when you are setting configuration options.

DFunction button: Press repeatedly to toggle through the following modes:

•

Studio: Use one of three studio (white light) presets, or customize the presets.

•

Color: Use one of 12 color presets, or customize the presets.

•

Preset: Use one of 12 presets (color preset + fade time), or customize the presets.

•

Effects: Use one of 12 effects, or customize the effects.

•

DMX: View and set DMX parameters for the fixture.

See

Use Fixture in Stand-aloneMode on page7

and

Use Fixture in DMX Mode on page6

EEncoders(Red, Green, Blue):The colors of encoders correspond to options on the display. Press to

activate the options at the bottom of the display, or turn to modify the values on the display.

FUSB port: Use for updating firmware, saving and loading fixture configuration settings, or saving

error logs via a flash drive.

GUI lock: Set this switch to lock the UI. This prevents inadvertent changes to the UI.

ETC Quick Guide

fos/4 Fresnel

fos/4 Fresnel Page 3 of 8 ETC

Safety

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the

following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

•

Do not use outdoors.

•

Do not let power supply cords touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should be mounted in locations and at

heights where it will not readily be subjected to

tampering by unauthorized personnel.

•

The use of accessory equipment not

recommended by the manufacturer

may cause an unsafe condition.

•

Do not use this equipment for other

than intended use.

SAVE THESE INSTRUCTIONS

Note:

The light source in this luminaire is not user-replaceable, and must be replaced

only by a qualified technician. Contact ETC Customer Support for assistance.

WARNING: Note the following safety warnings before use:

•

Use the fixture in dry locations only, where humidity does not exceed 90

percent (non-condensing).

•

Connect the fixture to a non-dimmable power source in order to avoid

damage to the fixture's internal power supply and other electrical

components. Using a dimmable power source can damage the fixture and

will void the warranty.

•

Disconnect the fixture from power and DMX and allow it to cool before

installing accessories or performing any cleaning and maintenance.

•

Only use mounting hardware that is rated for the total weight of the

fixture and accessories.

•

In addition to primary suspension, attach a safety cable (or other approved

safety device) to the fixture. Safety cables must be rated to support ten

times the fixture weight. Consult local standards to ensure that safety

cables meet all requirements. See

Mounting and Safety Cables on the next

page

•

Check that the accessory holder is locked and that any accessory safety

cables are connected before mounting the fixture.

•

Do not mount the fixture on or near a flammable surface.

•

Do not operate the fixture without the lens installed.

•

Do not use this fixture with a damaged power lead. If the power lead

(cord set) is damaged, it must be replaced.

•

Do not use this fixture if the lens is deeply scratched or cracked. You must

replace the lens when it is damaged.

ETC Quick Guide

fos/4 Fresnel

fos/4 Fresnel Page 4 of 8 ETC

AVERTISSEMENT : Prendre connaissance des avertissements de sécurité

suivants avant toute utilisation :

•

Débranchez le projecteur de son alimentation et du DMX et laissez-le

refroidir avant d’installer des accessoires ou d’effectuer un nettoyage ou

un entretien.

•

N’utilisez que de la quincaillerie de montage adaptée au poids total des

projecteurs et des accessoires.

•

En plus de la suspension principale, fixez une chaîne de sécurité (ou tout

autre dispositif de sécurité homologué) au projecteur. Les chaînes de

sécurité doivent être en mesure de supporter dix fois le poids du

projecteur. Consultez les normes locales pour vous assurer que les câbles

de sécurité respectent toutes les exigences.

•

Vérifiez que le porte-accessoires est verrouillé et que les élingues de tous

les accessoires sont bien attachées avant de monter le projecteur.

•

Ne pas installer le projecteur sur ou à côté d’une surface inflammable.

•

N’utilisez pas le projecteur sans que la lentille soit installée.

•

Ne pas utiliser ce projecteur avec un cordon d’alimentation endommagé.

Si le cordon d’alimentation (câble) est abîmé, il doit être remplacé.

•

N’utilisez pas ce projecteur si la lentille présente des rayures ou des

fissures profondes. Il faut remplacer la lentille si elle est abîmée.

Mounting and Safety Cables

You can mount the fixture using a clamp, baby-pin (16mm) receiver, or

spigot on the yoke(A), or you can set the fixture on the floor or another

flat surface. When suspending the fixture, make sure to secure the

fixture with an appropriate safety cable at the safety cable attachment

point (B).

If necessary, move the adjustable yoke (Din image below) to balance

the fixture. Use a 13 mm socket wrench to loosen the bolt and shift the

yoke position, and then tighten the bolt to secure the yoke.

Add Accessories

You can use up to two standard accessories (one scrim and

one additional accessory, such as a barn door) in the

accessory holder.

1. Unlock the accessory holder on either side by pressing

the spring-release and rotating the accessory holder lock

(C).

2. Slide an accessory into one of the accessory slots. Add a

second accessory in the other slot, if needed.

3. Lock the accessory holder by rotating the accessory

holder lock back into place.

4. If necessary, move the adjustable yoke (D) to balance

the fixture when using heavier accessories.

ETC Quick Guide

fos/4 Fresnel

fos/4 Fresnel Page 5 of 8 ETC

Connect Power and Data

1. Attach five-pin XLR cable to the

DMX In connector (if using external

control).

2. Plug the XLR cable (if using) into the

DMX source or data daisy-chain.

3. Use the DMX Thru connectors to

connect up to 32 device loads on

the DMX daisy chain.

4. Are you using AC power or battery

power?

•

AC power: Continue to step5.

•

Battery power:Continue to step6.

5. Use the Power Thru connectors to

connect other fixtures using the

following recommended guidelines,

and then continue to step 6:

•

Power Thru: Link up to 6 additional

fixtures (12A max) via Power Thru

connector when using an R20 Relay Module (consult breaker-trip curves when using other

equipment).

6. Supply power to the fixture in one of these ways:

•

Attach the power cable to the Power In connector, and then plug the power cable into AC

power (100–240VAC, 50/60 Hz) on a non-dimmable circuit.

•

Attach the three-pin XLR cable to the Battery connector, and then plug the cable into the

battery (24–36VDC). Cable must be rated for 10A or greater.

CAUTION:

Do not connect the fixture to the battery when AC power is present.

Maximum fixture output may be reduced when the fixture is connected to battery

power.

Focus the Fixture

1. Apply power to the fixture, and wait until the fixture has booted up(the ETC splash screen

displays during boot up).

2. Press any encoder to "wake" the display.

3. What screen is currently displayed?

•

DMX:Press the Intensity encoder to turn on the LED array. The display shows a timeout

countdown to indicate how long the LED array will remain on at 100% intensity. You can

turn the Intensity encoder to reset the timeout countdown to 5minutes.

•

All other screens (Studio, Preset, etc.): Press the Intensity encoder to turn on the

LEDarray, and turn the Intensity encoder to adjust the intensity.

4. Adjust the fixture to the desired position.

5. Rotate the zoom knob on either side of the fixture to adjust from spot to flood.

6. Press the Intensity encoder to turn off the LEDarray.

ETC Quick Guide

fos/4 Fresnel

fos/4 Fresnel Page 6 of 8 ETC

Use Fixture in DMX Mode

After you connect power and data to the fixture and provide DMX, press the Function button ( )

repeatedly to toggle to the DMX screen, where you can set the DMX address, DMXmode, and

DMXloss behavior. (You can also set these values using RDM.)

The DMX screen displays the current DMX values. Press any of the encoders to "wake" the display

and edit the values. The colors of the encoders correspond to options on the display. Turn an

encoder to modify the corresponding value, and then press the encoder to save the new value.

DMX

Address

Mode

DMX Loss

1/3 Red

DMX

Address

Mode

DMX Loss

1/3 Red

001

3 Ch RGB

HLL

001

3 Ch RGB

HLL 2 Min

Press any encoder to wake the display... ...and then turn an encoder to modify the value in

the matching field. Press an encoder again to save

the value and return to the view-only screen.

DMXModes

Direct

(DaylightHDR)

Direct

(Lustr X8) Expanded Studio 3 Ch RGB 1 Channel

RDMPersonality ID 1 1 2 3 4 5

DMXChannel 

1 Intensity Intensity Intensity Intensity Red Intensity

2 Deep Red Deep Red CCT CCT Green

3 Red Red Tint Tint Blue

4 Mint Amber Tuning Tuning

5 Cyan Lime Mix Strobe

6 Blue Green Red Curve

7 Indigo Cyan Green Fan

8 Strobe Blue Blue

9 Curve Indigo Strobe

10 Fan Strobe Curve

11 Curve Fan

12 Fan

ETC Quick Guide

fos/4 Fresnel

fos/4 Fresnel Page 7 of 8 ETC

Use Fixture in Stand-aloneMode

After you connect power to the fixture, press the Function button ( ) repeatedly to toggle through

the following modes:

•

Studio: Use one of three studio (white light) presets, or customize the presets.

•

Color: Use one of 12 color presets, or customize the presets.

•

Preset: Use one of 12 presets (color preset + fade time), or customize the presets.

•

Effects: Use one of 12 effects, or customize the effects.

•

DMX: View and set DMX parameters for the fixture.

The colors of options on the display correspond to the colors of the encoders below the display and

the Intensity encoder to the right of the display. Turn an encoder to modify the corresponding value

on the display, or press an encoder to activate the corresponding option at the bottom of the display.

Press the Intensity encoder to toggle between the current intensity and 0%.

If the fixture is connected to other fos/4 Fresnel fixtures that are in the same stand-alone mode, the

connected fixtures will play the same preset or effect.

Select a Color Temperature

1. Press the Function button ( ) until the display shows the Studio screen.

Studio

3200K 4500K 5600K

CCT 3200 K

Tint 0.0 Green

Tune Brightest

Int 100%

Studio

3200K 4500K 5600K

CCT 3125 K

Tint 0.0 Green

Tune Brightest

Int 100%

Press an encoder to play that

studio preset...

...or turn an encoder to modify the

value in the matching field.

Turn to adjust intensity, or press to

toggle between current intensity and 0.

DMX

2. Press the color encoder that matches the studio preset you want to use (Blue = 3200K,

Green= 4500K, Red= 5600K).

More Options

•

Turn off the preset: Press the Intensity encoder to toggle the intensity value from the current

value to 0. Press the Intensity encoder again to toggle back to the previous intensity value.

•

Modify the preset:Turn the encoders to change the corresponding values. For example, turn

the Intensity encoder to change the intensity value, or turn the blue encoder to change the

color temperature value.

•

Revert to the original preset:Press the encoder that corresponds to the preset again to restore

the original values.

ETC Quick Guide

fos/4 Fresnel

fos/4 Fresnel Page 8 of 8 ETC

•

Save the modified preset:Press and hold the encoder that corresponds to the preset that you

want to re-record. The display shows a three-second countdown before re-recording the

preset.

Select a Color

1. Press the Function button ( ) until the display shows the Color screen.

2. Turn the encoders to change the corresponding values. For example, turn the Intensity

encoder to change the intensity value, or turn the green encoder to change the hue value. The

crosshairs on the display indicate the approximate color.

You can use a preset as a starting point for a color by pressing the color encoder that matches

the preset. Turn the red encoder to move to another page of presets.

More Options

•

Turn off the color: Press the Intensity encoder to toggle the intensity value from the current

value to 0. Press the Intensity encoder again to toggle back to the previous intensity value.

•

Revert to the original color of a preset: Press the encoder that corresponds to the preset again

to restore the original values.

•

Save the color to a preset:Press and hold the encoder that corresponds to the preset that you

want to re-record. The display shows a three-second countdown before re-recording the

preset. Changes that you make to presets in the Color screen also affect presets in the Effects

screen and the Preset screen.

Select a Preset

1. Press the Function button ( ) until the display shows the Preset screen.

2. Turn the green encoder to select a preset, and then press the encoder to play the preset.

More Options

•

Pause the preset fade: Press the green encoder to toggle between play and pause.

•

Stop the preset: Press the red encoder.

•

Modify the preset:Turn the Intensity encoder to change the intensity, or turn the red encoder

to change the fade value.

•

Capture the current DMX look: Press and hold the blue encoder (for the Snapshot icon ).

The display shows a 3-second countdown before re-recording the preset. Capture is limited to

three DMX modes: 3 Ch RGB,Studio, and Expanded.

•

Modify the preset color:Press the blue encoder (for the Edit icon ). In the Edit Preset Color

screen, turn the encoders to change the corresponding values. The crosshairs on the display

indicate the approximate color. Press the green encoder (for the Save icon ) to save the

new color to the preset.

•

Push the preset to connected fixtures:Press the Menu button ( ), and then use the Intensity

encoder to navigate through the menu: Local Settings>Push Presets. When the screen

prompts you to confirm, press the green encoder (for the OK icon ) to continue.

Andere Handbücher für fos/4 Fresnel

Inhaltsverzeichnis

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Irideon AR50 Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC SolarFrame 750 Bedienungsanleitung

ETC

ETC Express 24/48 Bedienungsanleitung

ETC

ETC Source Four Zoom Bedienungsanleitung

ETC

ETC microVision FX Bedienungsanleitung

ETC

ETC XDLT 26 Bedienungsanleitung

ETC

ETC XDLT Bedienungsanleitung

ETC

ETC fos/4 Panel Pole-Operated Yoke Bedienungsanleitung

ETC

ETC ColorSource PAR Bedienungsanleitung

ETC

ETC Lustr+ Bedienungsanleitung

ETC

ETC Desire D22 Bedienungsanleitung

ETC

ETC Acclaim 100 series Bedienungsanleitung

ETC

ETC Express Bedienungsanleitung

ETC

ETC Sensor IQ DALI Control Option Card Bedienungsanleitung

ETC

ETC ColorSource Spot Bedienungsanleitung

ETC

ETC HIGH END SYSTEMS SolaPix 37 Bedienungsanleitung

ETC

ETC Source Four MultiPAR Bedienungsanleitung

ETC

ETC F-Drive W1 Series Bedienungsanleitung

ETC

ETC Source 4WRD Bedienungsanleitung

ETC

ETC Desire D60 XTI Bedienungsanleitung

ETC

ETC Desire Fresnel Bedienungsanleitung

ETC

ETC GDS BluesSystem Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung

ETC fos/4 Fresnel Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken