ETC High End Systems SolaPix 7 Bedienungsanleitung

High End Systems

SolaPix 7

Automated Luminaire User Manual

Version 2.0.2

Part Number: 2594M1200-2.0.2 Rev: A

Released: 2023-05

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked

and not marked, are the property of their respective owners.

You can find complete High End Systems terms and conditions and warranty information at

etcconnect.com/Support/Warranty.aspx.

For a complete list of all third-party licenses that are fully incorporated herein to the extent required by each

third-party license terms and conditions, please visit etcconnect.com/licenses.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents

Table of Contents i

Introduction 1

Document Conventions 1

Help from Technical Services 2

Safety Considerations 3

General Operation and Use Guidelines 5

Fixture Overview 6

Modular Control 7

Specifications 7

Environment 7

Power 8

Electrical 8

Input and Power Factor 8

Connector Specifications 8

Install the Fixture 9

DMX Control 11

DMX Connector Pinout 11

Connect DMXCables to Fixture 11

Terminate DMX 12

Set the DMX Start Address 12

DMX Channels 12

Ethernet Control 13

Connect EthernetCables to a Fixture 13

Set the DMX Start Address 14

Set the Control Source and Universe 14

Configure the Fixture 15

Navigate the User Interface 15

Set Fixture Parameters 16

Address 16

Info Menu 20

Set Menu 22

Test Menu 26

Preset Menu 26

Error Codes 27

Maintenance 28

Clean the Fixture 28

Replace the Fuse 28

Compliance 29

FCC Compliance 29

ii SolaPix 7 User Manual

Introduction 1

Introduction

Congratulations on your purchase of the High End Systems SolaPix 7 automated fixture.

This manual provides important information for the safe installation, configuration, and

maintenance of your SolaPix 7 fixture. For your safety, read this entire manual prior to

installing, operating, or servicing the fixture.

ETC recommends that you update your fixture with the latest version of software before you

use the fixture. Software is available for free download from the ETC website:

etcconnect.com/Products/Automated-Fixtures.

• See

View Software Version on page21

to determine which version of software is

currently installed on your fixture.

• See

Update Fixture Software Using the USB Port on page25

for instructions about

updating your fixture.

Document Conventions

This document uses the following conventions to draw your attention to important

information.

Note:

Notes are helpful hints and information that is supplemental to the main text.

CAUTION: A Caution statement indicates situations where there may be

undefined or unwanted consequences of an action, potential for data loss or

an equipment problem.

CAUTION: Hot Surfaces. This statement indicates that while operating,

equipment surfaces may reach very high temperatures. Allow the

fixture to cool before handling or servicing.

WARNING: A Warning statement indicates situations where damage may

occur, people may be harmed, or there are serious or dangerous

consequences of an action.

WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates

situations where there is a risk of electric shock.

All ETC High End Systems documents are available for free download from our website:

etcconnect.com/Products/Automated-Fixtures.

Please email comments about this manual to: TechComm@etcconnect.com.

2 SolaPix 7 User Manual

Help from Technical Services

If you have questions that are not answered by this document, try the ETC support website at

support.etcconnect.com or the High End Systems product website at

etcconnect.com/Products/Automated-Fixtures. If none of these resources are sufficient,

contact ETC Technical Services directly at one of the offices identified below. Emergency

service is available from all offices outside of normal business hours.

When calling for help, take these steps first:

• Prepare a detailed description of the problem

• Go near the equipment for troubleshooting

• Find your notification number if you have called in previously

ETC, Inc.

Americas

Technical Services Department

3031 Pleasant View Road

Middleton, WI 53562

800-775-4382 (USA, toll-free)

+1-608 831-4116

service@etcconnect.com

ETC GmbH

Germany, Austria, Switzerland,

Eastern Europe, and Russia

Technical Services Department

Ohmstrasse 3

83607 Holzkirchen, Germany

+49 (80 24) 47 00-0

techserv-germany@etcconnect.com

ETC Austin

High End Systems Products

Technical Services Department

2105 Gracy Farms Lane

Austin, TX 78758 USA

800-890-8989 (USA, toll-free)

+1-512 836-2242

hesservice@etcconnect.com

ETC France

France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

techservfrance@etcconnect.com

ETC Ltd

Europe, Middle East, and Africa

Technical Services Department

26-28 Victoria Industrial Estate

Victoria Road,

London W3 6UU England

+44 (0)20 8896 1000

techservltd@etcconnect.com

ETCAsia

Asia

Technical Services Department

Room 1801, 18/F

Tower 1, Phase 1 Enterprise Square

9 Sheung Yuet Road

Kowloon Bay, Kowloon, Hong Kong

+852 2799 1220

techserv-asia@etcconnect.com

Safety Considerations 3

Safety Considerations

To ensure safe operation, follow the safety instructions and warning notes in the user manual.

• This fixture is intended for professional use only. Not for residential use. Read the entire

manual before using this equipment.

• Contact your authorized ETC dealer or Technical Services before performing any service

in order to maintain warranty coverage.

WARNING: Note the following safety warnings before use:

• This equipment is designed for operation by qualified personnel only.

• Do not stare at the operating lamp. May be harmful to the eyes.

• Replace fuses with the specified type and rating only. See

page 28

• Ensure that the available voltage is within the stated range. See

page 8

• Do not use this fixture with a damaged power lead (cord set). If the lead

is damaged, it must be replaced by a qualified technician with an

equivalent type before use. Contact your local authorized dealer for

replacement power leads.

• Do not use this fixture if the lens is damaged. Damaged lenses must be

replaced before use. Contact your local authorized dealer for a

replacement.

• Do not mount the fixture on or near flammable surfaces.

• The fixture should be positioned so that prolonged staring into the

fixture at a distance closer than 6.4 m (21 ft) is not expected.

• Minimum distance from fixture head to combustible materials:

0.1 m (4.0 in).

• Minimum distance to lighted objects:1.0 m (3.28 ft).

AVERTISSEMENT : Pour votre sécurité, lisez les mises en garde et les avis

suivants avant toute utilisation :

• Cet équipement est conçu pour être utilisé par un personnel qualifié

uniquement.

• Ne regardez pas la lampe en fonctionnement. Peut être nocif pour les

yeux.

• Remplacez les fusibles uniquement par le type et le calibre indiqués.

Voir

page 28

• Veillez à ce que la tension disponible soit dans la plage indiquée. Voir

page 8

• N'utilisez pas ce projecteur avec un cordon d'alimentation endommagé

(fils électriques). Si le cordon est endommagé, un technicien qualifié doit

le remplacer par un cordon de type équivalent avant que l'appareil ne

puisse être utilisé. Contactez votre distributeur agréé local pour obtenir

des cordons d'alimentation de rechange.

• N'utilisez pas cet appareil si la lentille est endommagée. Les lentilles

endommagées doivent être remplacées avant l'utilisation. Contactez

votre revendeur agréé local pour un remplacement.

• Ne pas installer le projecteur sur ou à côté d’une surface inflammable.

• L'appareil doit être positionné de manière à ce qu'un regard prolongé

dans l'appareil à une distance inférieure à 6,4 m (21 pi) soit peu

probable.

• Distance minimum entre la tête du luminaire et les matériaux

combustibles : 0.1 m (4.0 in).

• Distance minimum avec les objets éclairés :1.0 m (3.28 ft).

4 SolaPix 7 User Manual

WARNING: RISK OF ELECTRIC SHOCK!

• Do not operate this device with the cover open.

• Disconnect the fixture from power and DMX and allow it to cool before

performing any cleaning and maintenance.

AVERTISSEMENT : RISQUE DE CHOC ÉLÉCTRIQUE!

• N'utilisez pas cet appareil avec le couvercle ouvert.

• Débrancher la lampe de son alimentation et du DMX et la laisser

refroidir avant d’effectuer un nettoyage ou un entretien.

RISK GROUP 2: CAUTION. Possibly hazardous optical radiation emitted

from this product. Do not stare at operating lamp. May be harmful to the

eyes.

GROUPE DE RISQUE 2 (RISQUE MODÉRÉ) : ATTENTION. Rayonnement optique

potentiellement dangereux émis par ce produit. Ne regardez pas la lampe en

fonctionnement. Peut être nocif pour les yeux.

CAUTION: Hot Surfaces. Allow the device to cool completely before

handling and servicing.

ATTENTION : Surfaces chaudes. Laissez le luminaire refroidir complètement

avant de le manipuler et de procéder à son entretien.

Note:

The light source in this luminaire is not user-replaceable, and must be

replaced only by a qualified technician. Contact ETC Customer Support for assistance.

Symbols used on the product label are defined below:

1.0 m

The luminaire must be installed at least 1.0m (3ft

4in) away from all lighted objects.

Le luminaire doit être installé à au moins 1,0m

(3pi. 4po.) de tout objet éclairé.

General warning Avertissement général

Do not stare at the operating light source. Ne pas regarder la source de lumière lorsqu’elle

fonctionne.

This product should not be discarded as unsorted

waste but must be sent to separate collection

facilities for recovery and recycling.

Ce produit ne doit pas être jeté avec les déchets

ménagers mais doit être déposé dans une collecte

de déchets électroniques ou dans un point de

collecte.

taorTaRated maximum ambient temperature Température ambiante maximale recommandée

Operate indoors only, not where this product

would be exposed to the weather.

Ne fonctionne qu'à l'intérieur, pas là où ce produit

serait exposé aux intempéries.

Safety Considerations 5

General Operation and Use Guidelines

• This fixture is only allowed to be operated with the maximum alternating current that is

stated in the technical specifications label provided on the fixture.

• Lighting effects are not designed for permanent operation. Consistent operation breaks

may extend the life of the fixture.

• When choosing the installation location, make sure the fixture will not be exposed to

extreme heat, moisture, or dust.

• Do not point the lens toward the sun or other bright light source. Doing so could damage

the fixture.

• If using the supplied brackets with quick-locking thumb screws for fixture hanging,

ensure that the thumb screws have engaged a complete 90-degree positive latch.

• Operate the fixture only after having familiarized yourself with its functions. Do not

permit persons who are not qualified and familiar with its functions to operate the

fixture.

• Do not modify the fixture. Any modifications will void the warranty.

• This manual describes the proper installation and operation of this fixture. Using this

fixture in any way other than the intended use may cause damage and void the warranty.

• When the fixture has been stored or transported in cold temperatures, allow it to warm

to room temperature for a minimum of one hour before applying power. Applying power

to a cold fixture may cause damage to the fixture and void the manufacturer warranty.

• When you power on the fixture, you may notice smoke or odor. This is normal and should

decrease gradually. If smoke or odor persists, disconnect the fixture from power and

contact your ETC dealer or Technical Services.

• Please use the original packaging if the fixture is to be transported. ETC will not be

responsible for the fixture if packaging other than manufacturer provided packaging is

used.

6 SolaPix 7 User Manual

Fixture Overview

345

78910

1: Lens

2: Tilt lock

3: Display

4: Navigation controls

5: Pan lock

6: Ethernet ports (x2)

7: DMX Thru

8: DMX In

9: Power In

10: USB

11: Power Out

Andere Handbücher für High End Systems SolaPix 7

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC SolarFrame 750 Bedienungsanleitung

ETC

ETC ColorSource Spot VXT Bedienungsanleitung

ETC

ETC Cyberlight LED Bedienungsanleitung

ETC

ETC ArcLamp System Bedienungsanleitung

ETC

ETC Source Four LED series Bedienungsanleitung

ETC

ETC Express 24/48 Bedienungsanleitung

ETC

ETC Source Four Revolution Rotating Wheel Module Bedienungsanleitung

ETC

ETC Aero Wave Station Bedienungsanleitung

ETC

ETC Echo Bedienungsanleitung

ETC

ETC Source Four Mini LED Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Desire D22 Bedienungsanleitung

ETC

ETC fos/4 Panel Pole-Operated Yoke Bedienungsanleitung

ETC

ETC Source Four HID PARNel Bedienungsanleitung

ETC

ETC microVision FX Bedienungsanleitung

ETC

ETC ColorSource CYC Bedienungsanleitung

ETC

ETC 3 Series Bedienungsanleitung

ETC

ETC ColorSource Spot Bedienungsanleitung

ETC

ETC GDS BluesSystem Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Source Four Zoom Bedienungsanleitung

ETC

ETC Source Four CE 405 Bedienungsanleitung

ETC

ETC ArcSystem Pro One-Cell Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung