EtherWAN EL100 Bedienungsanleitung

Media Converter

User’s Manual 1

Preface

This manual describes how to install and use the Ethernet Media

Converter with the link-fault-pass-through function. The Converter

introduced here provides one channel media conversion between

10/100Base-TX and 100Base-FX.

The Converter fully complies with IEEE802.3 10Base-T and

IEEE802.3u 100Base-TX/FX standards.

In this manual, you will find:

yProduct overview

yFeatures on the media converter

yIllustrative LED functions

yInstallation instructions

ySpecifications

Media Converter

2 User’s Manual

Table of Contents

PREFACE ................................................................................................................... 1

TABLE OF CONTENTS ............................................................................................... 2

INTRODUCTION ......................................................................................................... 3

PRODUCT OVERVIEW ............................................................................. 3

PRODUCT FEATURES ............................................................................. 3

PACKING LIST ........................................................................................ 4

ONE-CHANNEL MEDIA CONVERTER........................................................................ 5

PORTS ................................................................................................... 5

PORT SETTINGS ..................................................................................... 5

FRONT PANEL &LEDS.......................................................................... 6

LINK-FAULT-PASS-THROUGH ................................................................. 6

INSTALLATION.......................................................................................................... 8

SELECTING A SITE FOR THE EQUIPMENT................................................. 8

CONNECTING TO POWER ........................................................................ 8

INSTALLING IN A CHASSIS ...................................................................... 8

SPECIFICATIONS ....................................................................................................... 9

Media Converter

User’s Manual 3

Introduction

The media converter provides one channel for media conversion

between 10/100Base-TX and 100Base-FX. It can be used as a stand

alone device or with a standard 19” chassis as shown below.

Product Overview

<NOTE> The chassis is to be ordered separately.

Product Features

yOne-channel media conversion between 10/100Base-TX and 100Base-FX

yFiber media allows:

•Multi-mode fiber using SC, ST, VF-45, MT-RJ or LC connector

•Single-mode fiber using SC or ST connector

•WDM single-fiber (bi-direction) transceiver: Single-mode WDM fiber using SC connector:

A type: WDM single-fiber (bi-direction) transceiver transmits with 1310nm wavelength

and receives with 1550nm wavelength

B type: WDM single-fiber (bi-direction) transceiver transmits with 1550nm wavelength

and receives with 1310nm wavelength

yAuto negotiation of speed and duplex mode on TX port

yAuto MDIX on TX port

yOne DIP switch for configuring link-fault-pass-through, fixed speed, and half/full duplex

y2048 MAC addresses, 768K bits buffer memory

yStore-and-forward mechanism

yNon-blocking full wire-speed forwarding rate

ySupport broadcast storm filtering

yBack-pressure & IEEE802.3x compliant flow control

yFront panel status LEDs

yExternal AC to DC power adapter

yUsed as a stand-alone device or with a chassis

yHot-swappable when used with a chassis

Media Converter

4 User’s Manual

Packing List

When you unpack this product package, you will find the items listed

below. Please inspect the contents, and report any apparent damage or

missing items immediately to our authorized reseller.

yThe Media Converter

yUser’s Manual

yAC to DC Power Adaptor

Media Converter

User’s Manual 5

One-Channel Media Converter

Ports

The Converter provides one TX port and one FX port. For the FX port,

it provides options of

Multi-mode fiber using SC, ST, VF-45, MT-RJ or LC connector or

Single-mode fiber using SC or ST connector or

WDM fiber using single SC connector

For the TX port, it uses RJ-45 connector and auto senses the speed of

10/100Mbps.

Port Settings

Port settings are made very simple by means of a DIP (Dual Inline

Package) switch at the rear panel of the module.

1 2 3 4 5 6

DIP switch

There are six pins on the DIP switch for port settings. Refer to the table below for more details.

DIP

switch

No.

Down (Default Setting) Up

1 Enable LFPT Disable LFPT LFPT:

link-fault-pass-

through

2 Enable auto negotiation for TX port Enable forced mode for TX port

3 TX port forced to 100Mbps TX port forced to 10Mbps

4 TX port forced to full duplex mode TX port forced to half duplex mode

5 FX port forced to full duplex mode FX port forced to half duplex mode

yFirst, disconnect the converter from the power. Then toggle Pin 2 of the DIP switch to the up position

to enable the forced mode for TX port.

<NOTE> Pin 2 must be toggled up prior to speed and duplex mode settings

manually.

yToggle down Pin 3 to force the TX port at the speed of 100Mbps. Or toggle up Pin 3 for 10Mbps

speed.

yToggle down Pin 4 to force the TX port at full duplex mode. Or toggle up Pin 4 for half duplex mode.

yToggle down Pin 5 to force the FX port at full duplex mode. Or toggle up Pin 5 for half duplex mode.

yToggle up Pin 1 to disable the link-fault-pass-through.

yConnect the converter to the power again. The new setting will come into effect then.

Media Converter

6 User’s Manual

Front Panel & LEDs

LED Indicators

The LED indicators give you instant feedback on status of the converter:

LEDs State Indication

Steady Power on

PWR stands for POWER

PWR

Off Power off

Steady Connection at the speed of 100Mbps100 (Mbps)

Off Connection at the speed of 10Mbps

Steady A valid network connection established

LNK stands for LINK

Flashing Transmitting or receiving data

ACT stands for ACTIVITY

LNK/ACT

Off Neither valid network connection established

nor transmitting/receiving data.

Steady Connection in full duplex mode

FDX stands for FULL-DUPLEX

Flashing Collision occurred

COL stands for COLLISION

FDX/COL

Off Connection in half-duplex mode

Link-Fault-Pass-Through

Connect the FX ports of two Media Converter A and B through the fiber

cable.

1. Link Fault of the FX port:

A Link Fault condition will be sensed on the TX port whenever the

media converter detects a Link Fault condition on the FX port. Thus,

the 100, LNK/ACT, and FDX/COL LEDs of the media converter

would be off.

2. Link Fault of the TX port of the Media Converter A:

The Media Converter A: A Link Fault condition will be sensed on

the FX port whenever the media converter detects a Link Fault

condition on the TX port. Thus, the 100, LNK/ACT, and FDX/COL

LEDs of the TX port of the Media Converter A would be off.

The Media Converter B: A Link Fault condition will be informed to

the FX port of the Media Converter B. Then a Link Fault condition

will be sensed on the TX port of the Media Converter B whenever

the Media Converter B detects a Link Fault condition on the FX

port. Thus, the 100, LNK/ACT, and FDX/COL LEDs of the Media

Converter B would be off.

Media Converter

User’s Manual 7

Link Fault of the FX port

TX Port FX Port

LEDs PWR 100 LNK/ACT FDX/COL LNK/ACT FDX/COL

Media

Converter

ON OFF OFF OFF OFF OFF

Media

Converter

ON OFF OFF OFF OFF OFF

Link Fault of the TX port of the Media Converter A

TX Port FX Port

LEDs PWR 100 LNK/ACT FDX/COL LNK/ACT FDX/COL

Media

Converter

ON OFF OFF OFF ON ON

Media

Converter

ON OFF OFF OFF OFF OFF

Media Converter

8 User’s Manual

Installation

This chapter gives step-by-step installation instructions for the

Converter.

Selecting a Site for the Equipment

As with any electric device, you should place the equipment where it

will not be subjected to extreme temperatures, humidity, or

electromagnetic interference. Specifically, the site you select should

meet the following requirements:

zThe ambient temperature should be between 32 and 113 degrees Fahrenheit (0 to 45 degrees

Celsius).

zThe relative humidity should be less than 95 percent, non-condensing.

zSurrounding electrical devices should not exceed the electromagnetic field (RFC) standards for

IEC 801-3, Level 2 (3V/M) field strength.

zMake sure that the equipment receives adequate ventilation. Do not block the ventilation holes

on each side of the equipment.

zThe power outlet should be within 1.8 meters of the product.

Connecting to Power

yThis Converter is a plug-and-play device.

yConnect the supplied AC to DC power adaptor to the receptacle on the rear panel of the converter,

and then attach the plug into a standard AC outlet.

Installing in a Chassis

The Converter can be fit into any of the expansion slots on a special

designed chassis.

yFirst, install the converter onto a carrier supplied with the chassis:

Step 1- Unscrew the carrier from the desired expansion slot on the chassis.

Step 2- Fit the converter onto the carrier.

yWhen the converter is completely seated onto the carrier, insert the carrier to the guide rails of the

expansion slot.

yCarefully slide in the carrier until it is fully and firmly fit the chassis. Fasten the screws onto the

carrier.

<NOTE> Never insert any converter into the chassis directly without using the

supplied carriers. The carriers allow secure and consistent placement

of the converters into the chassis’ backplane without causing any

damage.

Media Converter

User’s Manual 9

Specifications

Applicable Standards IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX & 100Base-FX

Fixed Ports 1 TX port, 1 FX port

10/20Mbps for half/full-duplex10Base-T speed

100Base-TX/FX speed 100/200Mbps for half/full-duplex

Switching Method Store-and-Forward

Forwarding rate 14,880/148,810pps for 10/100Mbps

Per Unit- (2 LEDs): Power; 100(Mbps)LED Indicators

Per Port- (2 LEDs): LNK/ACT; FDX/COL

Dimensions 80.3mm (W) × 109.2mm (D) × 23.8mm (H)

(3.16” (W) × 4.30” (D) × 0.94” (H))

Weight 150g (0.33lb.)

Power External power adaptor 0.16A @ 12VDC

Power Consumption 1.92W Max.

Operating Temperature 0℃~ 45℃(32℉~ 113℉)

Storage Temperature -10℃~ 70℃(14℉~ 158℉)

Humidity 5 ~ 95%, non-condensing

Safety UL60950-1

Emissions FCC Part 15 Class A, CE Mark Class A

Andere Handbücher für EL100

Inhaltsverzeichnis

Andere EtherWAN Medienkonverter Handbücher

EtherWAN

EtherWAN EL2242-BT Bedienungsanleitung

EtherWAN

EtherWAN EMC1600 Series Bedienungsanleitung

EtherWAN

EtherWAN EL8000 Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL2326 Series Bedienungsanleitung

EtherWAN

EtherWAN EL1141 Series Bedienungsanleitung

EtherWAN

EtherWAN EMC1600 Series Bedienungsanleitung

EtherWAN

EtherWAN EL900 Series Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL9020 Bedienungsanleitung

EtherWAN

EtherWAN EMC400 Bedienungsanleitung

EtherWAN

EtherWAN EL900 Series Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL2321 Bedienungsanleitung

EtherWAN

EtherWAN EL1032T Series Bedienungsanleitung

EtherWAN

EtherWAN EL2242 Bedienungsanleitung

EtherWAN

EtherWAN EL100T Bedienungsanleitung

EtherWAN

EtherWAN EL900 Series Bedienungsanleitung

EtherWAN

EtherWAN EMC1200R Bedienungsanleitung

EtherWAN

EtherWAN EM1100 Bedienungsanleitung

EtherWAN

EtherWAN EMC1600 Series Bedienungsanleitung

EtherWAN

EtherWAN EL1142 Series Bedienungsanleitung

EtherWAN

EtherWAN EL2211 Bedienungsanleitung

EtherWAN

EtherWAN EL2321 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung