EUFY RoboVac 11+ Bedienungsanleitung

www.eufylife.com

For FAQs and more information, please visit:

T2104 51005001010 V07

Cleaning

Owner’s Manual

RoboVac 11+

Table of Contents

02 About Your RoboVac

What's In the Box

RoboVac Anatomy

06 Using Your RoboVac

Important Tips Before Use

Install the Charging Base

Charge Your RoboVac

Start / Stop Cleaning

Select a Cleaning Mode

Set Time and Schedule Cleaning

14 Cleaning and Maintenance

Clean the Dust Collector and Filters

Clean the Rolling Brush

Clean the Sensors and Charging Pins

Clean the Side Brushes

Replace the Side Brushes

17 Troubleshooting

19 Speciﬁcations

19 Customer Service

Thank you for purchasing RoboVac 11+. Read all instructions before using this product, and

keep it properly for future reference.

02 03

RoboVac Anatomy

Top & Side

Auto cleaning Start/Stop button

Bumper

Dust collector

Main power switch (On/O)

Infrared sensor

Dust collector release button

Bottom

Drop sensors

Charging contact pins

Brush guard

Swivel wheel

Side brushes

Wheels

Dust collector

Rolling brush

About Your RoboVac

What's In the Box

Additional High-

Performance Filter

Additional Foam Filter

Power Adapter Cleaning Tool Additional Side

Brushes (×2)

RoboVac 11+ Charging Base Remote Control

(AAA Battery ×2)

Owner’s Manual &

Other Documents

04 05

Remote Control

Start/Stop Auto cleaning

Control cleaning direction manually

Adjust the hour and minute

Set the current time

Schedule Auto cleaning start time

Start Spot cleaning

Start Edge cleaning

Start Single Room cleaning

Return RoboVac to Charging Base

Install 2 AAA batteries before using the remote control for the first time. Make sure

the positive and negative ends are facing the correct polarity direction as marked in

the battery compartment.

Dust Collector

High-performance ﬁlter

Foam ﬁlter

Pre-ﬁlter

Suction Inlet

Suction inlet

Dust collector

Charging Base

Status light

Charging contact pins Power socket

06 07

Install the Charging Base

Place the Charging Base on a hard, level surface and against a wall.

Remove objects within 3 ft/1 m of the left and right side and within 6 ft/2 m of the

front of the charging base.

Connect the round connector of the adapter into the power socket on the Charging

Base and the other end into a wall outlet.

T- Install the Charging Base in a

location that RoboVac can easily

access.

- Always keep the Charging Base

plugged in, otherwise RoboVac

will not automatically return to it.

- The LED indicator on the Charging Base is SOLID GREEN when RoboVac is NOT

docked.

- The LED indicator on the Charging Base is OFF when RoboVac is docked.

Using Your RoboVac

Important Tips Before Use

abc

Remove power cords and small objects from the floor that may entangle RoboVac.

Fold tasseled edges of area rugs underneath to prevent tangling RoboVac. Avoid

cleaning very dark-colored high-pile rugs or rugs thicker than 0.87 in/22 mm as they

may cause RoboVac to malfunction.

Keep RoboVac away from spaces lower than 3.9 in/100 mm to prevent RoboVac from

getting stuck. If necessary, place a physical barrier to block off the problem areas.

Keep RoboVac away from wet areas.

RoboVac may climb on top of objects less than 0.59 in/15mm in height. Remove these

objects if possible.

Anti-drop sensors prevent RoboVac from tumbling down stairs and steep drops. They

may work less effectively if dirty or used on reflective/very dark-colored floors. It is

recommended to place physical barriers to block off areas where RoboVac may fall.

Place physical barriers in front of fireplaces and areas that may cause damage to

RoboVac if entered.

08 09

Turn off the power switch if RoboVac will not be used for a long period of time. To

preserve the battery’s lifespan, recharge at least once every 3 months.

Start / Stop Cleaning

1. Turn on the main power supply

Press the main power switch on the side of RoboVac to turn on the main power supply.

2. Start cleaning

Press on RoboVac or on the remote control to start cleaning in Auto mode.

3. Stop cleaning

Press on RoboVac or on the remote control to stop cleaning.

Select a Cleaning Mode

1. Auto cleaning

RoboVac automatically cleans in a back-and-forth, straight-line pattern. This is the most

commonly used cleaning mode.

Press on RoboVac or on the remote control to start cleaning in Auto Mode.

Charge Your RoboVac

• RoboVac has a pre-installed rechargeable battery that has to be fully charged before use.

• RoboVac returns to the Charging Base at the end of a cleaning cycle or when its battery is

running low.

• Make sure the main power switch on the side of RoboVac is turned on before charging.

Method 1: Attach RoboVac to the Charging Base by aligning its charging pins with the

charging pins on the base.

Method 2: Press on the remote control to return RoboVac to the Charging Base.

(Status Light) Status

Breathing blue Charging

Solid blue Standby / Cleaning / Returning to Charging Base

Solid purplish-red Low power and returning to Charging Base

Flashing / Solid red + Beeping RoboVac has an error

O

RoboVac is o

To conserve power, the light automatically turns o:

When RoboVac is not docked to the Charging Base and

has been inactive for 10 minutes

After RoboVac is docked to the Charging Base and has

been fully charged for 10 minutes

10 11

3. Edge cleaning

RoboVac reduces its speed when it detects a wall and then follows the wall to ensure the

edge is cleaned thoroughly. In Edge mode, RoboVac will clean for 20 minutes and return to

the Charging Base.

Press on the remote control to start cleaning in Edge Mode.

4. Single Room cleaning

RoboVac intensively cleans one single room and stops after 30 minutes. Select this mode

only when one specific room needs to be cleaned. Make sure to confine RoboVac to the

room by closing the door.

Press on the remote control to start cleaning in Single Room Mode.

- RoboVac will return to the Charging Base automatically when the battery level

becomes low or when RoboVac finishes cleaning.

- By default, RoboVac starts in Auto cleaning mode when it is turned on.

BoostIQ™ Feature

When the BoostIQ™ feature is enabled, RoboVac will automatically increase the suction

power if it detects stronger power is needed to ensure the best clean. BoostIQ™ is ideal for

cleaning thicker carpets and hard-to-sweep messes, which will reduce the total cleaning time,

but increase the noise level. If the vacuuming noise caused by BoostIQ™ disturbs you, you can

disable this feature. This feature only works in Auto and Single Room cleaning modes.

To adjust the suction power level in Auto or Single Room cleaning mode, simultaneously

press and hold the and buttons for 2 seconds; you will hear a series of beeps that

correspond to the suction power selected. Repeat to adjust the suction power level.

Suction Power Level Beeps

Standard power

BoostIQ™

(Default, automatically switches between Standard and

Enhanced power)

Maximum power

When RoboVac starts cleaning in Auto or Single Room mode the next time, it will clean

according to the suction power level you previously selected.

2. Spot cleaning

RoboVac intensively cleans a specific area in a spiral pattern, useful if there is a concentrated

area of dust or debris. In Spot mode, RoboVac will stop cleaning after 2 minutes.

Press on the remote control to start cleaning in Spot Mode.

12 13

To ensure the time is set successfully, make sure RoboVac is turned on. You will hear

a beep when the time has been set.

2. Set a Scheduled Cleaning

You can schedule RoboVac to start cleaning at a specified time. To cancel a previously

scheduled cleaning, press and hold for 3 seconds until RoboVac beeps twice and

disappears.

Before setting a scheduled cleaning, make sure the time has been set correctly to your

local time; refer to the previous section “Set Time” for how to set time.

Make sure the main power switch on the side of RoboVac is turned on.

Press on the remote control. will blink on the display.

Press to set the “hour” and “minute”.

Note: Make sure AM/PM is set correctly.

Press or to save the setting. RoboVac will BEEP ONCE to indicate the schedule

has been set.

To ensure the schedule is set successfully, make sure RoboVac is turned on. You

will hear a beep when the schedule has been set.

5. Manual cleaning

You can direct RoboVac to clean a particular area by using the directional buttons on the

remote control.

Move backward

Move forward

Turn left

Turn right

Set Time and Schedule Cleaning

1. Set Time

Make sure the time is set correctly to your local time before setting a scheduled cleaning.

Make sure the main power switch on the side of RoboVac is turned on.

Press on the remote control. will blink on the display.

Press to set the “hour” and “minute”.

Note: Make sure AM/PM is set correctly.

Press or to save the setting. RoboVac will BEEP ONCE to indicate the time has

been set.

14 15

Push the dust collector back into the main unit.

- It is recommended to empty the dust collector and clean the filter after every use.

- You can wash the dust collector, pre-filter and foam filter with water. Be sure to

air-dry them thoroughly before reassembling. Do not wash the high-performance

filter with water, as it may damage the filter and reduce the suction power.

Clean the Rolling Brush

Pull on the release tabs to unlock brush guard as shown.

Lift the rolling brush to remove.

Clean the rolling brush with the provided cleaning tool or a vacuum cleaner.

Reinstall the rolling brush by inserting the fixed protruding end first and then clicking

into place.

Press down to snap the brush guard into place.

Cleaning and Maintenance

Clean the Dust Collector and Filters

Press the dust collector release button to pull the dust collector out.

Open and empty the dust collector.

Separate the pre-filter by pulling the hooks as shown.

Take out the foam filter and high-performance filter.

Clean the dust collector and filter with a vacuum cleaner or a cleaning brush.

Put the filters back together in the dust collector.

16 17

Pull off the old side brushes and snap the new ones into place.

Screw down the screws to fasten the side brushes.

Troubleshooting

Problem Solutions

RoboVac cannot be

activated.

•Make sure the main power switch is in the ON position.

•Make sure the battery is fully charged.

•Replace the batteries (2 AAA) in the remote control.

•Make sure the remote control is within range (less than

6 ft/2 m from RoboVac).

•If you still have trouble, turn o the main power switch and then

turn it back on.

The remote control

does not work.

•Replace the batteries in the remote control.

•Make sure RoboVac is turned on and fully charged.

•If RoboVac and the remote control’s display work properly, but

RoboVac does not respond to the remote control’s commands,

it may be because the remote control has not been paired with

RoboVac.

In this case, do not dock RoboVac to the Charging Base. Turn o

the main power switch and then:

(1) press and hold on the remote control until the icon

blinks on the display;

(2) turn on the main power switch.

You will hear three beeps after successful pairing.

RoboVac stops

working suddenly.

•Check if RoboVac is trapped or stuck on an obstacle.

•Check if the battery level is too low.

•If you still have trouble, turn o the main power switch, wait for

2 seconds, and then turn it back on.

RoboVac does not start

scheduled cleaning.

•Make sure the main power switch on the side of RoboVac is

turned on.

•Make sure the time, time of day (AM/PM), and the scheduled

time have been set correctly.

•Check if RoboVac’s power is too low to start cleaning.

Clean the Sensors and Charging Pins

To maintain the best performance, clean the drop sensors and charging pins regularly.

• Dust off the drop sensors and charging contact pins using a cloth or cleaning brush.

Clean the Side Brushes

Foreign substances, such as hair, can easily get tangled in the side brushes and dirt may adhere to

them. Be sure to clean them regularly.

Carefully unwind and pull off any hair or string that is wrapped between the main unit

and the side brushes.

Use a cloth dampened with warm water to remove dust from the brushes or to gently

reshape them.

Only use the side brushes when they are completely dry.

Replace the Side Brushes

The side brushes may become bent or damaged after being used for a period of time.

Follow the instructions below to replace them.

Use a screwdriver to unscrew the screws on the side brushes.

Inhaltsverzeichnis

Andere EUFY Staubsauger Handbücher

EUFY

EUFY RoboVac 15C Bedienungsanleitung

EUFY

EUFY HomeVac H11 Bedienungsanleitung

EUFY

EUFY RoboVac 30C Bedienungsanleitung

EUFY

EUFY HomeVac S11 Go Bedienungsanleitung

EUFY

EUFY RobVac G15 Bedienungsanleitung

EUFY

EUFY HomeVac S11 Lite Bedienungsanleitung

EUFY

EUFY X9Pro Bedienungsanleitung

EUFY

EUFY RoboVac 11 Bedienungsanleitung

EUFY

EUFY RoboVac 30 Bedienungsanleitung

EUFY

EUFY T2520 Bedienungsanleitung

EUFY

EUFY T2521 Bedienungsanleitung

EUFY

EUFY HOMEVAC T2401 Bedienungsanleitung

EUFY

EUFY RoboVac Series Bedienungsanleitung

EUFY

EUFY RoboVac 11c+ Bedienungsanleitung

EUFY

EUFY RoboVac 25C Bedienungsanleitung

EUFY

EUFY RoboVac 11S Bedienungsanleitung

EUFY

EUFY T2501 Bedienungsanleitung

EUFY

EUFY RoboVac G20 Hybrid Bedienungsanleitung

EUFY

EUFY HomeVac H20 Bedienungsanleitung

EUFY

EUFY RoboVac 35C Bedienungsanleitung

EUFY

EUFY RoboVac L70 Hybrid Bedienungsanleitung

EUFY

EUFY T2194 Bedienungsanleitung

EUFY

EUFY RoboVac Bedienungsanleitung

EUFY

EUFY Clean G35 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung