Extech Instruments PQ34-12 Bedienungsanleitung

1200A Current Probe Set

Model PQ34-12

actoolsupply.com

Extech PQ34-12 Current Clamp Meter Probes 1200 Amp

PQ-12-EU-EN V1.0 01/12

Introduction

Congratulations on your purchase of this Extech Current Probe Set. A set of three 1200A current

probes designed to be used with the Extech PQ3450 or PQ3470 Power Analyzers. These probes

are shipped fully tested and calibrated and, with proper use, will provide years of reliable service.

Safety

This symbol, adjacent to another symbol or terminal, indicates the user must refer to the

manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages

may be present

Double insulation

Cautions

Read and understand this user manual before operating the meter.

Improper use of this meter can cause damage, shock, injury or death.

Inspect the condition of the leads and the meter itself for any damage before operating the

meter.

Use great care when making measurements if the voltages are greater than 25VAC rms or

35VDC. These voltages are considered a shock hazard.

Do not attempt to measure Current that exceeds specified limits

Do not operate this instrument in wet or dusty environments.

Do not operate this instrument in the presence of combustible or explosive gas

Do not touch exposed metal parts or unused terminals.

Use protective gloves near high current or voltage circuits.

If the equipment is used in a manner not specified by the manufacturer, the protection provided

by the equipment may be impaired.

actoolsupply.com

PQ-12-EU-EN V1.0 01/12

Probe Description

1. Current Sensing Jaws

2. Jaw Trigger

3. 1200A-200A-20A range switch

4. Signal output plug ( +, red )

5. Signal output plug ( -, black )

6. DCV power plug

Operation

1. Connect the “A1” signal output cables to the matching input sockets

on the top of the analyzer.

2. Connect the “A1” power cable to the matching power socket on the

top of the analyzer.

3. Set the "1200A-200A-20A” range switch to the range appropriate for

the application.

Note: Make sure the range set on the clamp matches the range

set in the analyzer.

4. Connect the “A2” and “A3” clamps as above, if needed.

5. Press the "Trigger" to open the jaws and clamp around a single

conductor.

6. Power on the power analyzer

actoolsupply.com

PQ-12-EU-EN V1.0 01/12

Specifications

Measurement ranges 20A, 200A and 1200A, switch selectable

Output sensitivity 10mV/A on the 20A range

1mV/A on the 200A range

0.1mV/A on the 1200A range

Output coupling AC coupled.

Accuracy (50/60Hz) ± 1% F.S. @ 23 ± 5°C

Frequency range 45 to 400 Hz.

Phase error (50/60Hz) < ± 1°

Minimum load 100 K ohm for specified accuracy

Enclosure material UL 94-V0 rated

Safety IEC 1010, Category III 600V

Power Supply 8V± 1V (supplied from meter)

Max. Jaw Open Size 50 mm (2.0 inch) Dia.

Operating Temperature 0°C to 50°C (32°F to 122°F)

Operating Humidity Less than 80% RH

Dimension 210 x 64 x 33 mm. (8.3 X 2.5 X 1.3”inch )

Cable length : 4 meters (13.17 feet)

DC plug size : 5.5 mm x 2.5 mm DIA.

Weight 490 g (1.08 LB)

Safety For indoor use and in accordance with the requirements for

indoor use, double insulation to IEC1010-1 (2001):

EN61010-1 (2001) Overvoltage Category III 600V,, Pollution

Degree 2.

actoolsupply.com

Andere Handbücher für PQ34-12

Inhaltsverzeichnis

Andere Extech Instruments Messgerät Handbücher

Extech Instruments

Extech Instruments PH90 Bedienungsanleitung

Extech Instruments

Extech Instruments DT500 Bedienungsanleitung

Extech Instruments

Extech Instruments MA3110 Bedienungsanleitung

Extech Instruments

Extech Instruments 461995 Bedienungsanleitung

Extech Instruments

Extech Instruments AN320 Bedienungsanleitung

Extech Instruments

Extech Instruments 380460 Bedienungsanleitung

Extech Instruments

Extech Instruments LT10 Bedienungsanleitung

Extech Instruments

Extech Instruments 407113 Bedienungsanleitung

Extech Instruments

Extech Instruments CLT600 Bedienungsanleitung

Extech Instruments

Extech Instruments RC100 Bedienungsanleitung

Extech Instruments

Extech Instruments 401025 Bedienungsanleitung

Extech Instruments

Extech Instruments 475055 Bedienungsanleitung

Extech Instruments

Extech Instruments MG310 Bedienungsanleitung

Extech Instruments

Extech Instruments GRT350 Bedienungsanleitung

Extech Instruments

Extech Instruments RH300 Bedienungsanleitung

Extech Instruments

Extech Instruments C015 Bedienungsanleitung

Extech Instruments

Extech Instruments MA410T Bedienungsanleitung

Extech Instruments

Extech Instruments TKG100 Bedienungsanleitung

Extech Instruments

Extech Instruments EC100 Bedienungsanleitung

Extech Instruments

Extech Instruments RPM250W Bedienungsanleitung

Extech Instruments

Extech Instruments ET38 Bedienungsanleitung

Extech Instruments

Extech Instruments TKG250 Bedienungsanleitung

Extech Instruments

Extech Instruments 461995 Bedienungsanleitung

Extech Instruments

Extech Instruments MO210 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung