Extraflame LUCREZIA IDRO LCD Bedienungsanleitung

PELLET STOVES

Instruction Manual

LUCREZIA IDRO

Pagina 2

Congratulations! You are now t e owner of an EXTRAFLAME stove!

The EXTRAFLAME pellet stove is an ideal heating solution. It utilises the most advanced

technology and is manufactured to the highest standards with a contemporary design,

allowing you to enjoy the ambience and warmth of a natural flame in complete safety.

This manual tells you how to use your stove correctly. Please read the entire manual

carefully before using your stove.

IMPORTANT

Make sure that the dealer completes the following bo with the details of the authorised

specialist who will help you if you have any problems in using your new pellet stove.

AUTHORISED SPECIALIST

Company___________________________________________________________________

Full name __________________________________________________________________

Address ______________________________________________ No._________________

Postal Code _________________ City _________________________________________

TEL. _____________________________ FAX ____________________________________

Pagina 3

Pagina 4

Contents

1 PRECAUTIONS AND SAFETY 5

2 TECHNICAL SPECIFICATIONS 6

3 WHAT ARE PELLETS? 7

3.1 Pellet storage 7

4 SAFETY DEVICES 8

4.1 Warm air blower breakdown 8

4.2 Pellet feed motor breakdown 8

4.3 Lighting failure 8

4.4 Temporary power failure 8

4.5 Electrical safety 8

4.6 E haust system safety 8

4.7 Pellet overheating safety 8

4.8 System pressure safety 8

4.9 Water boil safety 8

4.10 E ternal devices 8

4.11 Installation and safety devices 8

4.12 Safety for open e pansion tank system 8

4.13 Safety for closed e pansion tank system 8

5 ASSEMBLY AND INSTALLATION INSTRUCTIONS 9

5.1 Glossary 9

5.2 Installation 10

5.2.1 Connection to the e haust venting system 11

5.2.2 Chimney or single flue 12

5.2.3 Connection to the flue and combustion product e haust venting 14

5.2.4 Chimney cap 14

5.2.5 Connection to e ternal air intakes 15

5.2.6 Insulation, trims, facings, and safety precautions 15

5.2.7 National, regional, provincial and municipal laws 15

6 CONTROL PANEL 16

6.1 Table of display messages 17

7 Language selection 20

8 Current day and time settings 20

9 OPERATING MODES 21

9.1 E ternal thermostat operation in STBY-TOFF mode 24

10 USING THE STOVE 25

11 LIGHTING 25

12 STOVE OPERATION 26

12.1 Normal operation 26

12.2 Shutdown 26

12.3 Remote control 26

13 REGULATING THE WATER TEMPERATURE 27

14 USER PARAMETERS 28

14.1 Weekly programmer 29

14.2 Pellet feed adjustment 31

14.3 Automatic cleaning schedule 32

15 STOVE CLEANING 33

15.1 Chimney connection 34

16 FIRST LIGHTING OPERATIONS 35

16.1 Fitting the tiles 35

16.2 Burn pot bracket 37

16.3 Burn pot positioning 37

17 WIRING DIAGRAM 38

18 WARRANTY 39

19 QUALITY CONTROL 41

Pagina 5

1. PRECAUTIONS AND SAFETY

The stoves manufactured in our factory are built

with the ma imum dedication to the individual

components so as to protect both the user and

the installer from accidents. Authorized personnel

are therefore advised to pay special attention to

the electrical connections after any servicing

operation on the product, especially with regard

to the stripped part of the wires, which must not

protrude in any way from the terminal block to

prevent possible contact with the live parts of the

wire.

Installation must be carried out by

aut orized personnel, w o must issue t e

purc aser a declaration of compliance of

t e system. T e purc aser s all assume

responsibility for t e definitive installation

and consequent proper operation of t e

product installed. Extraflame S.p.A. may

not be eld responsible in t e event of

failure to observe t ese precautions.

This instruction manual constitutes an integral

part of the product. It must always accompany

the appliance, also when it is transferred to

another owner or user or moved to another

location. If the manual gets damaged or lost, ask

your local service centre for another copy.

This stove must only be used for the applications

for which it was e pressly designed.

The manufacturer declines any responsibility,

contractually or e tra-contractually, for any

damage caused to persons, animals or property

by errors in installation, adjustment, and

maintenance, or by improper use.

After removing the packaging, check to make

sure that the contents are intact and complete.

If this is not the case, contact the vendor from

whom the appliance was purchased.

The electrical components of the stove must only

be replaced by an authorized service centre.

General stove maintenance must be carried out at

least once a year, scheduled sufficiently in

advance with the service centre.

T e following safety precautions must be

observed:

Do not allow the stove to be used by unattended

children or disabled persons.

Do not touch the stove if you are bare-footed or if

parts of your body are wet or damp.

Modifying the safety or adjustment devices without

the manufacturer’s approval or instructions is

forbidden.

Never pull, detach, or twist the electrical cables

coming out of the stove, even if it is disconnected

from the electrical power.

Do not plug or reduce the size of the air vents of

the room in which the stove is installed.

The air vents are critical for correct combustion.

Keep the packaging materials out of the reach of

children and unattended disabled persons.

Prior to installation, we recommend that you

thoroughly clean all the piping of the system to

remove any residues that could jeopardise the

efficient operation of the appliance.

During installation, the user should be informed

that:

a. In the event of water leakage, the water supply

must be closed off and the service centre must be

notified promptly.

b. The operating pressure of the system must be

checked periodically. When the stove is not used

for an e tended period of time, we recommend

asking the technical service to carry out at least

the following operations:

- Put the master switch in position 0.

- Close the water taps on both the heating and

plumbing systems.

- Empty the heating and plumbing systems if there

is a risk of freezing.

Pagina 6

2. TECHNICAL SPECIFICATIONS

Unit of

measurement Lucrezia Idro

Height mm 1330

Width mm 544

Depth mm 594

Weight kg 297

E haust pipe diameter mm 120

Air intake pipe diameter mm 60

Ma . heating volume m³ 480

Total power (heating power) kW/h 4.2 – 24.0

Water heating power kW/h 17.5

Pellet consumption per hour kg/h 1.0 – 5.0

Absorbed electrical power W 25 - 270

Lighting power W +280

Power supply V, Hz 230, 50

Hopper capacity kg ~43

Water in/out pipe diameter " 1

Diam. autom. discharge pipe w/valve 3 bar

" 1/2

Pump position / Return

Pump head m 4

All data are indicative and not binding. The manufacturer reserves the right to make

technical modifications for improving the product.

All E traflame products are manufactured according to

the following directives:

•

89/106 EEC (CPD) construction materials

•

73/23 EEC (LVD) electrical safety

•

98/37 EEC machinery

•

2004/108 EEC (EMC) electromagnetic

compatibility

And the following standards:

•

prEN14785

•

EN60335.1 EN50165 EN50366

•

EN292 EN294

EN55014.1 EN55014.2 EN61000-3-2 EN61000-

3-3

Pagina 7

3. WHAT ARE PELLETS?

Pellets are made by applying very high

pressure to sawdust; i.e. the residue of raw

timber (without paint) produced by sawmills,

carpentry works and other activities involved

in processing wood.

This type of fuel is completely

environmentally friendly, as no binders of

any kind are used to keep it compact. In

fact, the compactness of the pellets over

time is guaranteed by lignite, a natural

substance found in the wood itself.

As well as being an environmentally friendly

fuel, since wood residues are e ploited to the

ma imum, pellets also have technical

advantages.

While the heating power of wood is 4.4

kW/kg (with 15% humidity, after about 18

months seasoning), the power of pellets is

5.3 kW/kg.

The density of the pellet is 650kg/m

and the

water content is 8% of its weight. For this

reason, pellets do not need to be seasoned

to obtain a sufficient heating yield.

Pellet diameters range from a minimum of 5

mm to a ma imum of 8 mm, though

E traflame recommends using 6 mm pellets.

3.1 Pellet storage

To guarantee problem-free combustion, the

pellets must be stored in a dry place.

WARNING

THE USE OF POOR QUALITY PELLETS OR ANY

OTHER MATERIAL MAY DAMAGE THE YOUR

STOVE AND MAY LEAD TO THE INVALIDATION

OF THE WARRANTY

AND THE RELATED RESPONSIBILITIES

OF THE MANUFACTURER.

Pagina 8

4. SAFETY DEVICES

4.1 Fume ex auster breakdown

If the e hauster stops, the electronic unit immediately prevents

pellet feeding.

4.2 Pellet feed motor breakdown

If the motor stops, the stove continues to operate until the

minimum cooling level is reached.

4.3 Lig ting failure

If no flame develops during the lighting stage, the stove display

shows “ NO ACC”. If you attempt to light the stove again, the

display shows “ATTE” which means “WAIT”. T is function

reminds you t at before lig ting t e stove, you must be

sure t at t e burn pot is free of dirt and debris.

4.4 Temporary power failure

The appliance will re-light automatically after a brief power

failure. When the power goes off, the stove may emit a minute

quantity of smoke inside the house for a period of 3 to 5

minutes.

THIS DOES NOT POSE ANY SAFETY RISK.

4.5 Electrical safety

The stove is protected against violent power swings by a

master fuse on the rear of the stove (2A 250V delayed).

4.6 Ex aust fume safety

If the e haust system fails, an electronic pressure switch stops

the stove and an alarm is signalled.

4.7 Pellet over eating safety

In case of overheating inside the pellet hopper, this safety

device blocks stove operation; resetting is manual and must be

performed by an authorized technician.

4.8 System pressure safety

A mechanical pressure switch blocks any over-pressure in the

system.

Reset is manual and must be carried out by an authorised

technician.

4.9 Water boil safety

In the event of a lack or minimum quantity of water, this

device blocks the pellet feed. Reset is manual and must be

carried out by an authorised technician.

4.10 External devices

During stove installation, it is MANDATORY to adapt the system

with a pressure gauge for viewing the water pressure and an

automatic blowdown valve calibrated at 3 bar pressure.

4.11 Installation and safety devices

The installation and respective system connections, the start-up

and final testing for correct operation must be carried out with

all due diligence by authorised professional technicians (Italian

Law no. 46 of 5 March 1990), in full respect for the regulations

in force, both national and regional, as well as for the

instructions given in this manual.

Extraflame S.p.A. declines any responsibility for

damage to objects and/or persons caused by t e

system.

4.12 Safety devices for open expansion tank system

Systems with open e pansion tank must be equipped with:

•Open e pansion tank

•Safety pipe

•Inlet pipe

•Thermostat for circulator control (e cluded for

systems with natural circulation)

•Circulation system (e cluded for systems with natural

circulation)

•Device for acoustic alarm activation

•Acoustic alarm

•Temperature indicator

•Pressure indicator

•Automatic cut-out switch

only for stoves with

automatic feed

The temperature safety sensors must be on-board the heat

generator or at a distance no greater than 30 cm from the

delivery connection.

If the heat generators are not equipped with all the devices,

the missing ones can be installed on the delivery piping of the

generator, at a distance of no more than 1 m from the it.

4.13 Safety devices for closed tank system

Closed systems must be equipped with:

•Safety value

•Thermal blowdown valve (positive safety)

•Closed e pansion tank

•Adjustment thermostat connected to the circulator

•Thermostat connected to the acoustic alarm

•Thermal cut-out switch for regulation (limitation

thermostat)

•Thermal cut-out switch for blocking (blocking

thermostat)

•Thermometer and pressure gauge

•Circulation system

•

Safety dissipation system built into the generator with

thermal blowdown valve.

The temperature safety sensors must be on-board the heat

generator or at a distance no greater than 30 cm from the

delivery connection.

If the generators are not equipped with all the devices, the

missing ones can be installed on the delivery piping of the

generator, at a distance of no more than 1 m from the

machine.

Pagina 9

5. ASSEMBLY AND INSTALLATION INSTRUCTIONS

The installation must comply with:

UNI 10683 (2005) heat generators fed with wood and other solid fuels: installation.

The chimneys must comply with:

UNI 9731 (1990) chimneys: classification according to thermal resistance.

UNI 9615 (1995) calculation of the internal dimensions of the chimneys with single connection.

UNI 7129 point 4.3.3 provisions, local rules and prescriptions of the fire brigade.

UNI 1443 (2005) chimneys: general requirements.

UNI 1457 (2004) chimneys: internal ducts in terracotta and ceramics.

5.1 Glossary

CLOSED HEARTH DEVICE

Heat generator that can only be opened to load fuel during use.

BIOMASS

Material of organic origin, e cluding the material incorporated in geological formations and

fossilised.

BIOFUEL

Fuel produced directly or indirectly from biomass.

FLUE or CHIMNEY

Vertical duct for collecting and e pelling combustion products from a single appliance at a suitable

height from the floor.

EXHAUST CHANNEL OR PIPE

Duct or connecting element between the heat generating device and the chimney for e tracting

the combustion products.

INSULATION

The series of measures taken and materials used to prevent heat transmission through a wall

dividing rooms at different temperatures.

CHIMNEY CAP

Device located at the top of the chimney that facilitates dispersion of the combustion products in

the atmosphere.

CONDENSATE

Liquid products that form when the temperature of the combustion gas is lower than or equal to

the dew point of the water.

HEAT GENERATOR

Device that permits the production of thermal energy (heat) by the rapid transformation of the

chemical energy of the fuel by means of combustion.

AIR LOCK

Mechanism for modifying the dynamic resistance of the combustion gasses.

Pagina 10

EXHAUST VENTING SYSTEM

A system for fume e haust venting that is independent from the appliance, composed of a pipe or

channel, chimney or single flue, and chimney cap.

FORCED DRAUGHT

Air circulation by means of a fan driven by an electric motor.

NATURAL DRAUGHT

Draught resulting in a chimney/flue due to the difference in the volume mass e isting between the

(hot) fumes and the surrounding atmospheric air, without any mechanical suction aid installed

inside or on top of it.

RADIANCE AREA

Area immediately adjacent to the hearth in which the heat produced by combustion is diffused;

this area must not contain any objects made of combustible material.

REFLUX AREA

Area in which the combustion products come out from the appliance towards the room in which it

is installed.

5.2 Installation

Before carrying out installation, it is necessary to check the positioning of the chimneys, flues or

e haust terminal ducts of the appliance, keeping in mind the following:

•Installation prohibitions

•Legal clearances

•Limitations set forth by local administrative regulations or specific regulations of the

authorities.

•Common limitations deriving from building regulations, and easement or contract

regulations.

Admissible installations

In the room in which the heat generator is to be installed, any e isting or installed appliances must

be airtight to the room and must not cause depression in the room with respect to the e ternal

environment.

Appliances used for cooking foods and the related hoods without e tractor can only be installed in

rooms used as kitchens.

Pro ibited installations

The room in which the heat generator is to be installed must not contain any of the following

devices, either pre-e isting or installed:

- Hoods with or without e tractor;

- Ventilation ducts of the collective type.

Should these devices be located in adjacent rooms communicating with the installation room, it is

forbidden to use the heat generator simultaneously where there is the risk that one of the two

rooms may be subject to depression with respect to the other.

Andere Handbücher für LUCREZIA IDRO LCD

Inhaltsverzeichnis

Andere Extraflame Pelletofen Handbücher

Extraflame

Extraflame DUCHESSA IDRO Bedienungsanleitung

Extraflame

Extraflame COMFORT P85 Bedienungsanleitung

Extraflame

Extraflame Viviana Bedienungsanleitung

Extraflame

Extraflame LUCIA PLUS Bedienungsanleitung

Extraflame

Extraflame DEBBY Bedienungsanleitung

Extraflame

Extraflame COMFORT IDRO Bedienungsanleitung

Extraflame

Extraflame Comfort Mini Bedienungsanleitung

Extraflame

Extraflame Comfort Plus Bedienungsanleitung

Extraflame

Extraflame HP 22 Bedienungsanleitung

Extraflame

Extraflame INSERTO COMFORT MINI Bedienungsanleitung

Extraflame

Extraflame Lucrezia Steel Bedienungsanleitung

Extraflame

Extraflame DELIZIA Bedienungsanleitung

Extraflame

Extraflame GLENDA WIFI Bedienungsanleitung

Extraflame

Extraflame EcoLogica Idro Bedienungsanleitung

Extraflame

Extraflame Pellet Stoves Bedienungsanleitung

Extraflame

Extraflame LUCIA Bedienungsanleitung

Extraflame

Extraflame COSTANZA IDRO Bedienungsanleitung

Extraflame

Extraflame Comfort P70 Bedienungsanleitung

Extraflame

Extraflame VIVIANA EVO Bedienungsanleitung

Extraflame

Extraflame BABYFIAMMA Bedienungsanleitung

Extraflame

Extraflame BABYFIAMMA Bedienungsanleitung

Extraflame

Extraflame LCD Bedienungsanleitung

Extraflame

Extraflame EcoLogica Idro Bedienungsanleitung

Extraflame

Extraflame SOUVENIR Bedienungsanleitung

Beliebte Pelletofen Handbücher anderer Marken

SMG

SMG Comfort Bilt HP50GC Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Palazzetti

Palazzetti JP Series Installationsanleitung

Travis Industries

Travis Industries Avalon 900 PS Bedienungsanleitung

Flame

Flame FP-45 Bedienungsanleitung

Astra

Astra P-7 Bedienungsanleitung

Heatilator

Heatilator ECO-ADV-PS35 Bedienungsanleitung

Cadel

Cadel aquos 24 h2O Bedienungsanleitung

vicenza

vicenza V4.5 Bedienungsanleitung

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Technisches Handbuch

Quadra-Fire

Quadra-Fire 1000 Gold Betriebsanleitung

Ferroli

Ferroli GEMMA Bedienungsanleitung

pleasant hearth

pleasant hearth PH35PS Series Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200M-MBK Bedienungsanleitung

England's Stove Works

England's Stove Works 25-EP Bedienungsanleitung

Avalon

Avalon Astoria Bedienungsanleitung

Spartherm

Spartherm Mellino Kurzanleitung