Extron electronics IN3212 Bedienungsanleitung

User’s Guide

Distribution Amplifier/Line Drivers

68-822-01 Rev. A

Printed in the USA

07 03

IN3212 and IN3214

IN3212 and IN3214 • Installation 3IN3212 and IN3214 • Normal and Split Mode (IN3214 Only)

Installation

Introduction

The IN3212™and IN3214™are high performance composite video

or (for IN3214 only) S-video distribution amplifiers with gain and

peaking controls. The IN3212 features 300 MHz (-3dB)

bandwidth and the IN3214 features 280 MHz (-3dB) bandwidth.

The compact design allows them to be installed in any convenient

location. They accept NTSC, PAL, and SECAM video signals, as

well as high resolution monochrome, and distribute the signal to

separately buffered outputs.

Both models are powered by an external 110V or 220V power

supply. The power supply included with each unit is appropriate

to the region where the DA is sold.

Features

• Two (IN3212) or four (IN3214) outputs — Distribute a video

signal from a single input to two or four outputs.

• Gain and Peaking controls — Compensate for long cable runs

and increase fine details and clarity.

• Quad-standard compatibility — Compatible with composite

NTSC 3.58, NTSC 4.43, PAL, and SECAM video as well as high

resolution monochrome video signals.

• Split mode operation (IN3214) — Can be functionally split

into two independent two-output distribution amplifiers.

• Local monitor loop-through — Provides a passive loop-

through signal for a local monitor, or to create a larger DA

system.

Normal and Split Mode (IN3214 Only)

The IN3214 can be configured to either normal mode or split mode.

•Normal mode (factory default) — A single 1-input by 4-output

composite video distribution amplifier (figure 1).

In this mode, the Loop Out/Input 2 connector can be jumpered

as a loop-through to provide a buffered local output signal.

•Split mode — Two, independent 1-input by 2-output DAs.

Composite video — The DA can accept two composite video

inputs and distribute eachinput to two separate outputs.

If a loop-through signal is required when the IN3214 is

configured for split mode and is buffering composite video, set

the inputs for High Z (see the jumper table on page 5) and use

a BNC “T” connector on the input to split the signal.

S-video — The DA can accept a single S-video input (with the

luminance [Y] input on one input connector and the

chrominance [C] input on the other) and distribute the Y/C

output to two separate S-video devices (figure 2).

Projector

Monitor

VCR

HDTV

Plasma

Video Camera

LCD Projector

OUTPUT

LOOPOUT/

INPUT2

OUTPUT1

OUTPUT2

OUTPUT3

OUTPUT4

INPUT

1-IN4-OUTVIDEODISTRIBUTION

AMPLIFIER/LINEDRIVER

3214

Extron

IN3214

Video Distribution

Amplifier

Figure 1 — Typical normal mode composite video

application

HDTV

Plasma

DVD

LCD

Projector

OUTPUT

LOOP OUT/

INPUT 2

OUTPUT 1

OUTPUT 2

OUTPUT 3

OUTPUT 4

INPUT

1-IN 4-OUTVIDEODISTRIBUTION

AMPLIFIER/ LINEDRIVER

3214

Extron

IN3214

Video Distribution

Amplifier

Figure 2 — Typical split mode S-video application

Installation

1. Turn off and disconnect all equipment.

2. If necessary, reconfigure the internal jumpers for the desired

mode and Loop Out/Input 2 connector termination. See Normal

and Split Mode (IN3214 Only) and Jumper configuration.

IN3212 and IN3214 • Furniture Mounting 5IN3212 and IN3214 • Jumper Configuration

Installation

3. Place the DA in the desired location or mount it in a convenient

location using the optional mounting brackets.

4. Connect the input device(s) to the input connector(s).

5. Connect the output devices to the output connectors.

CAUTION

Ensure you are using the correct power supply, 110V

or 220V, for your region. Using the wrong power

supply will damage the DA.

6. Apply power to all devices and turn on the input and

output devices.

7. Adjust the gain and peaking as needed. See Connections and

Controls.

Jumper configuration

The DA is factory configured in normal mode (IN3214 only) with

the Loop Out/Input 2 connector terminated (no loop-through).

For any other type of video, reconfigure the jumpers as follows:

1. Remove the screw on each side of the cover (figure 3).

OUTPUT

LOOPOUT/

INPUT2

OUTPUT1

OUTPUT2

OUTPUT3

OUTPUT4

INPUT

1-IN 4-OUT VIDEO DISTRIBUTION

AMPLIFIER / LINE DRIVER

3214

Remove screw

each side.

Remove the four

hex nuts.

Figure 3 — Opening the DA

2. Using an Extron BNC extraction tool (part #100-096-01) or a

14mm, deep well socket, remove the four hex nuts securing

the output BNC connectors to the rear panel. Slide the

cover forward until the cover clears the BNC connectors.

Lift the cover off.

3. Locate J2 through J5 on the printed circuit board (figure 4).

4. Set the jumpers as shown in the table on the following page.

5. Replace the cover and reinstall the screws.

Figure 4 — Jumper locations

Normal/75 ohms (default)

No loop-through on input 2.

Normal/High Z

Loop-through on input 2.

Split/75 ohms

Split/High Z

Shaded = IN3214 only, = jumper installed, = jumper removed.

Mode/Termination J5J3 J4J2

Furniture mounting

If desired, furniture mount the unit using the optional IN9127

mounting brackets, as follows:

1. Attach the mounting brackets to the distribution amplifier

with the provided machine screws (figure 5).

OUTPUT

LOOPOUT/

INPUT2

OUTPUT1

OUTPUT2

OUTPUT3

OUTPUT4

INPUT

1-IN4-OUTVIDEODISTRIBUTION

AMPLIFIER/LINEDRIVER

3214

Figure 5 — Desk mounting the IN3212 and IN3214

IN3212 and IN3214 • Specifications 7IN3212 and IN3214 • Connections and Controls

Furniture Mounting

2. Hold the unit with the attached brackets against the

underside of the table or other furniture. Mark the location

of the screw holes of the bracket on the mounting surface.

3. Drill 3/32” (2 mm) diameter pilot holes, 1/4” (6.3 mm) deep

in the mounting surface at the marked screw locations.

4. Insert #8 wood screws into the four pilot holes. Tighten

each screw into the mounting surface until just less than

1/4” of the screw head protrudes.

5. Align the mounting screws with the slots in the brackets

and place the unit against the surface, with the screws

through the bracket slots.

6. Slide the DA slightly forward or back, then tighten all four

screws to secure the unit in place.

Connections and Controls

LOOP OUT

1-IN 2-OUT VIDEO DISTRIBUTION

AMPLIFIER / LINE DRIVER

3212

OUTPUT1

OUTPUT2

OUTPUT

INPUT

MADEINU.S.A.

POWER

SHARPNESS

OUTPUT2

OUTPUT1

TECHNICAL SUPPORT:

(800) 882-7117

(714) 921-4100

9VDC 500 mA

GAIN

Top view Bottom view

Figure 6 — IN3212 connectors and controls

POWER

PEAK CONTROL

OUTPUT2

OUTPUT1

OUTPUT4

OUTPUT3

TECHNICALSUPPORT:

(800)882-7117

(714)921-4100

MADEINU.S.A.

9VDC 500 mA

GAIN CONTROL

PEAK CONTROL

GAIN CONTROL

LOOP OUT/

INPUT 2

1-IN 4-OUT VIDEO DISTRIBUTION

AMPLIFIER / LINE DRIVER

3214

OUTPUT1

OUTPUT2

OUTPUT3

OUTPUT4

OUTPUT

INPUT

Top view Bottom view

Figure 7 — IN3214 connectors and controls

Power connector — Plug the 9VDC power supply into this

connector.

CAUTION

Ensure you are using the correct power supply, 110V

or 220V, for your region. Using the wrong power

supply will damage the DA.

Video Output connectors — Connect up to two (IN3212) or

four (IN3214) composite video output devices, such as

projectors, VCRs, or monitors, to these female BNC connectors.

For an IN3214 configured in split mode and distributing

S-video, Outputs 1 and 2 output one video plane (Y or C)

and Outputs 3 and 4 output the other plane (C or Y).

Input 1 connector — Connect a composite video input or

(for the IN3214 only) an S-video Y or C input, such as from

a DVD player or a VCR, to this female BNC connector.

Loop-out/Input 2 connector —

Default configuration — In the factory default

configuration, this female BNC connector is not used.

Buffered loop-through — To provide a buffered loop-

through signal, the internal jumper settings must be

changed (see the jumper table on page 5).

Split mode (IN3214 only) — When the IN3214 is

configured for split mode, this female BNC connector

provides an input connection for a second signal source,

either composite video or an S-video C or Y input. See

Normal and Split Mode (IN3214 Only) for more details.

Gain control — Use a tweeker to adjust the amount of

amplification that is added to the video signal. The

adjustment range, assuming a 1.0V input, is from 0.7V (30%

decrease) to 1.4V (40% increase).

Peak/Sharpness control — Use a tweeker to adjust for the

best sharpness.

Specifications

Video

Gain ............................................... -3dB to +3dB, adjustable (0.7V p-p to

1.5V p-p output when input is 1V p-p)

Bandwidth .................................... IN3212: 300 MHz (-3dB)

IN3214: 280 MHz (-3dB)

Video input and loop-through

Number/signal type ................... 1 composite video

1 composite video loop-through

Connectors .................................... 2 female BNC

Nominal level ............................... 1V p-p

Minimum/maximum levels ...... Analog: 0.4V to 2.0V p-p with no offset at

unity gain

Impedance .................................... 75 ohms

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Daisan DMJ Building 6F

3-9-1 Kudan Minami

Chiyoda-ku, Tokyo 102-0074 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

Return loss .................................... <-35dB @ 5 MHz

Video output

Number/signal type

IN3212 ............................... 2 composite video

IN3214 ............................... 4 composite video

Connectors

IN3212 ............................... 2 female BNC

IN3214 ............................... 4 female BNC

Nominal level ............................... 1V p-p at unity gain

Minimum/maximum levels ...... 0.3V to 3.5V p-p

Impedance .................................... 75 ohms

Return loss .................................... <-35dB @ 5 MHz

DC offset ....................................... ±8mV maximum with input at 0 offset

Sync

Standards ...................................... NTSC 3.58, NTSC 4.43, PAL, SECAM

General

Power ............................................. 110VAC or 220VAC, 50/60 Hz, 2 watts,

external; to 9VDC, 500 mA power supply.

Product requires 0.1 A.

Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /

10% to 90%, non-condensing

Operating +32° to +122°F (0° to +50°C) /

10% to 90%, non-condensing

Rack mount ................................... Yes

Enclosure type .............................. Metal

Enclosure dimensions ................. 4.0" H x 5.6" W x 1.25" D

10.1 cm H x 14.2 cm W x 3.2 cm D

(Depth excludes connectors.)

Product weight ............................. 0.8 lbs (0.3 kg)

Shipping weight .......................... 2 lbs (1 kg)

Vibration ....................................... ISTA/NSTA 1A in carton (International

Safe Transit Association)

Listings .......................................... ETL (UL1950)

Compliances ................................. CE

MTBF ............................................. 30,000 hours

Warranty ....................................... 3 years parts and labor

Specifications are subject to change without notice.

Specifications

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extron electronics Verstärker Handbücher

Extron electronics

Extron electronics SVDA 6 A MX Bedienungsanleitung

Extron electronics

Extron electronics XPA Ultra Series Bedienungsanleitung

Extron electronics

Extron electronics MDA 4V EQ Bedienungsanleitung

Extron electronics

Extron electronics VersaTools MDA 3 Series Bedienungsanleitung

Extron electronics

Extron electronics AVDA 6 MX DUAL Bedienungsanleitung

Extron electronics

Extron electronics DTP HD DA 4K Series Bedienungsanleitung

Extron electronics

Extron electronics MDA 5SVA RCA Bedienungsanleitung

Extron electronics

Extron electronics TP T BNC DA4 Bedienungsanleitung

Extron electronics

Extron electronics MPA 122 Bedienungsanleitung

Extron electronics

Extron electronics VersaTools MDA 5V Bedienungsanleitung

Extron electronics

Extron electronics P/2 DA2 MT Bedienungsanleitung

Extron electronics

Extron electronics MPA 401-70V Bedienungsanleitung

Extron electronics

Extron electronics P/2 DA2 EC F Bedienungsanleitung

Extron electronics

Extron electronics IN3254 Bedienungsanleitung

Extron electronics

Extron electronics FOX DA8 Plus Bedienungsanleitung

Extron electronics

Extron electronics MDA 5V Bedienungsanleitung

Extron electronics

Extron electronics DVI DA2 Bedienungsanleitung

Extron electronics

Extron electronics VersaTools MDA 5A RCA Bedienungsanleitung

Extron electronics

Extron electronics MPA 401-70V Bedienungsanleitung

Extron electronics

Extron electronics D/2 DA4 DVI Bedienungsanleitung

Extron electronics

Extron electronics PVCA 452 Bedienungsanleitung

Extron electronics

Extron electronics XPA Ultra Series Bedienungsanleitung

Extron electronics

Extron electronics DA2 HD 4K PLUS Bedienungsanleitung

Extron electronics

Extron electronics Distribution Amplifiers DVI DA4 Plus Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung