Extron electronics RGB 580xi AAP Bedienungsanleitung

Setup Guide — RGB 580xi

This guide provides basic instructions for an experienced

installer to set up and operate the Extron RGB 580xi.

Installation

Refer to the RGB 580xi User’s Manual for details.

CInstallation and service must be performed by authorized personnel only.

Step 1 — Powering down

Turn off or disconnect all equipment from power sources.

Step 2 — Mounting

Mount the interface as desired.

Step 3 — Video input

Connect an RGBHV, RGBS, RGsB, or RsGsBs analog video input to the

front panel 15-pin HD input connector. The pinout table is shown below.

Pin Description Wire ID Pin Description Wire ID

15-pin HD male pinout table

1 red signal red coax

2 green signal green coax

3 blue signal blue coax

4 horizontal shift + green wire

5 horizontal shift —brown wire

6 red coax ground red coax shield

7 green coax ground green coax shield

8 blue coax ground blue coax shield

9 LED red orange wire

10 horizontal sync ground black coax shield

10 vertical sync ground yellow coax shield

10 audio ground black wire

10 LED ground yellow wire

10 shift ground grey wire

11 audio right red wire

12 audio left white wire

13 horizontal sync black coax

14 vertical sync yellow coax

15 LED green pink wire

Step 4 — Audio input

Connect an unbalanced stereo input to the front panel 3.5 mm stereo mini

jack.

Step 5 — Video output

Connect a display device to the rear panel video output BNC connectors, as shown below.

RGBSRGBHV RGsB (Sync on Green)

RsGsBs

(output only if input is RsGsBs)

R G B

H/HV

V R G B

H/HV

VR G B

H/HV

Step 6 — Audio output

Connect an audio device to the 3.5 mm, 5-pole captive screw connector for balanced or

unbalanced audio output. Wire the male connector as shown here.

CAUTION

For unbalanced audio, connect the

sleeve(s) to the ground contact.

DO NOT connect the sleeve(s) to the

negative (-) contacts.

Do not tin the wires!

Tip

NO Ground Here

Sleeve(s)

NO Ground Here

Tip

L R

Balanced Audio Output

Unbalanced Audio Output

Tip

Ring

Tip

Ring

L R

Sleeve(s)

15-pin HD Male Pin Locations

610

Sleeve ( )

Ring (R)

Tip (L)

Setup Guide — RGB 580xi

Step 7 — Contact closure

For contact closure, connect an optional contact closure device to the front panel 5-pin, captive

screw connector. Making contact closure between pins A and B transmits a channel signal

through the rear panel RS-232 port. The RGB 580xi SI/CCSI AAP models provide one-button

contact closure operation. Wire the male connector as shown below on the left. The Extron

VGA and control cable assembly comes with the male control connector prewired, as shown at

right.

Contact closure wiring

Contact closure

5 VDC

Ground

5 VDC

CONTROL

A B CDE

Prewired male control

connector

Male VGA connector

Prewired male control cable connector

NThe contact closure pins on the RGB 580xi’s front panel are not to be used for horizontal

shift control. See the horizontal shift control wiring in the 15-pin HD pinout table in

Step 3.

Contact closure Description

A Contact closure + Contact closure + circuit

B Contact closure - Contact closure - circuit

C +5 V +5 V source for powering AAP devices

D Gnd Signal ground for powering AAP devices

E -5 V -5 V source for powering AAP devices

RGB580xi contact closure pinout table.eps

Step 8 — Setting the DIP switches

The DIP switches control DDSP (Digital Display Sync Processing),

serration pulse output, SOG (sync on green) output, vertical sync width,

sync polarity, and composite sync output. Moving a switch up sets it to On

and moving it down sets it to Off.

NThe default for all DIP switches is Off (down).

1 — DDSP (Digital Display Sync Processing) — This feature may be necessary for digital

display devices such as LCD, DLP (digital light processing) and plasma displays. Use this

option if the image is not displayed properly after other options, such as serration pulse

and vertical sync pulse width, have been explored.

On — The interface uses DDSP instead of ADSP.

DDSP does not process the sync signal.

NDDSP disables the horizontal shifting control.

Off — The interface performs sync processing operations, such as centering, with ADSP.

2 — Serr (serration pulse) — Many LCD and DLP projectors and plasma displays must

have serration pulses removed from the sync signal in order to display properly. Flagging

or bending at the top of the video image is a sign that the serration pulses should be

removed.

On — The interface outputs serration pulses in the vertical sync interval.

Off — The interface does not output serration pulses.

SOG

SERR

DDSP

V-SYNC WIDTH

NEG SYNC

COMP SYNC

3 — SOG (sync on green)

On — The interface outputs sync on green.

Off — The interface outputs separate horizontal and vertical sync (on the H and

V connectors) for RGBHV.

4 — V-Sync Width (vertical sync pulse width) — For some digital display devices, if no

picture appears, the picture cuts in and out, or the picture is scrambled, try adjusting the

output vertical sync pulse width or switching from ADSP to DDSP.

On — The vertical sync pulse is narrow.

Off — The vertical sync pulse is wide.

5 — Neg Sync — This switch controls sync polarity.

On — Both the horizontal and the vertical sync signals are forced to negative polarity on

output.

Off — Output sync polarity follows (is the same as) input polarity.

6 — Comp Sync — This switch controls composite sync output.

On — The interface outputs combined horizontal and vertical sync for RGBS.

Off — The interface outputs RGBHV or RGsB video.

Step 9 — RS-232 control

For two-way RS-232 communication, connect an RS-232 device (control system or PC) to the

3-pole captive screw connector. Software for RS-232 control is included with the interface.

Refer to the “Remote Control” section of chapter 3 of the user’s manual for further details.

Wire the male connector, as shown here.

3-pin RS-232 Captive Screw Con_lateral.eps

Transmit

Receive

Ground

Tx Rx

RS-232

Front Panel Adjustments

Video signals passing through long cable runs of over 125 feet (38.1 meters) can decrease

in strength, creating signal loss. The longer the cable, the greater the cable resistance and

capacitance, and the greater the level and peaking adjustments that will be required to

compensate for the resultant signal loss. These adjustments change the level and peaking of the

output signal to compensate for capacitance caused by up to 1000 feet (304.8 meters) of Extron

SHR cable.

NIf the displayed image is too bright or too dark, try changing the level setting. If the edges

of the displayed image seem to exceed their boundaries, or if thin lines and sharp edges look

thick and fuzzy, try changing the peaking setting. See the illustration below.

SOG

SERR

DDSP

V-SYNCWIDTH

NEGSYNC

COMPSYNC

INPUTS

RGB 580xi

ANALOG

AUDIO CONTROL

VIDEO OUTPUT

LEVEL

A B C D E PEAKING

Level

Peaking

1. Level adjustment control — The Video Output Level control alters the brightness of the

displayed image. To adjust the video output level, view the display while using a small,

ﬂat-blade screwdriver to rotate this potentiometer.

If the interface receives a typical (0.7 volts p-p) analog computer video input, the output is

as follows:

Setup Guide — RGB 580xi

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

68-536-50

Rev. A

11 09

 •Attheminimumlevelsetting(thecounterclockwiselimitofthiscontrol),theinterface 

outputs video at 0.5 volts p-p.

 •Unitylevelis0.7voltsp-p,thesameastheinputsignal.Setthecontrolto  

approximately one-half turn between the minimum and maximum level settings

to output unity level video.

 •Atthemaximumlevelsetting(theclockwiselimitofthiscontrol),theinterfaceoutputs 

video at 1.45 volts p-p.

Select a level setting of 0.7 volts or above to compensate for the decrease in signal level that

occurs when the signal passes through long cables. Set the level at the maximum setting

for cable lengths over 500 feet for all computer signals of 15 kHz to 135 kHz.

2. Peaking control — The Video Output Peaking control affects the sharpness of a picture.

Increased peaking can compensate for detail (mid- and high-frequency) loss from low

bandwidth system components or capacitance in long cables.

 •Theminimumsetting(atthecounterclockwiselimit)providesnopeaking.

 •Themaximumsetting(attheclockwiselimit)provides100%peaking.

Adjust this control while viewing the displayed image to obtain

the optimum picture sharpness.

Operation

Turn on the input devices (computer, audio device) and output device(s) (projector,

monitors, speakers). After powering up the RGB 580xi, the image should now appear on the

screen, and sound should be audible. If you are experiencing problems, please refer to the

“Troubleshooting” section of the user’s manual.

Andere Handbücher für RGB 580xi AAP

Inhaltsverzeichnis

Andere Extron electronics Verstärker Handbücher

Extron electronics

Extron electronics MDA EQ Series Bedienungsanleitung

Extron electronics

Extron electronics DA Series Bedienungsanleitung

Extron electronics

Extron electronics MP 101 D Bedienungsanleitung

Extron electronics

Extron electronics VersaTools MDA 3 Series Bedienungsanleitung

Extron electronics

Extron electronics MPA 152 Bedienungsanleitung

Extron electronics

Extron electronics DVI DA2 Bedienungsanleitung

Extron electronics

Extron electronics NetPA Ultra Series Bedienungsanleitung

Extron electronics

Extron electronics DA2 HD 8K L Bedienungsanleitung

Extron electronics

Extron electronics VGA Distribution Amplifiers P/2 DA4xi s Bedienungsanleitung

Extron electronics

Extron electronics HDMI DA4 Bedienungsanleitung

Extron electronics

Extron electronics MPA 181T Bedienungsanleitung

Extron electronics

Extron electronics P/2 DA2 EC F Bedienungsanleitung

Extron electronics

Extron electronics MDA 3AV RCA Bedienungsanleitung

Extron electronics

Extron electronics P/2 DA2xi MT Bedienungsanleitung

Extron electronics

Extron electronics MPA 401-100V Bedienungsanleitung

Extron electronics

Extron electronics Fiber Optics Fox 4G DA8 Bedienungsanleitung

Extron electronics

Extron electronics P/2 DA2 Plus Bedienungsanleitung

Extron electronics

Extron electronics NetPA Ultra Series Bedienungsanleitung

Extron electronics

Extron electronics XTRA Series Bedienungsanleitung

Extron electronics

Extron electronics FOX DA8 Bedienungsanleitung

Extron electronics

Extron electronics XTRA Series Bedienungsanleitung

Extron electronics

Extron electronics SW2 VGA DA2 A Bedienungsanleitung

Extron electronics

Extron electronics MDA 3A Bedienungsanleitung

Extron electronics

Extron electronics FOX DA8 Plus Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung