Extron electronics IPCP Pro Series Bedienungsanleitung

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications bef

ore connecting the

oduct to the po

wer source.

IPCP Pro Series • Setup Guide

The Extron IPCPPro Series IPLink®Pro Control Processors integrate Ethernet connection into AV systems to allow users to

remotely control, monitor, and troubleshoot AV equipment, including display devices and switchers. All models include an

embedded web server. Depending on the model, an IPCPPro control processor can include multiple bidirectional serial ports,

relays, IR/serial ports, digital I/O, flex I/O, switched 12 VDC power output ports, a volume control port, or contact input ports for

use in applications that require control and monitoring of multiple devices within a large-scale AV system.

All models include an Extron eBUS port, which allows a variety of eBUS devices to be connected to a single control processor.

eBUS devices include an array of button panels as well as power and signal hubs. eBUS devices are automatically recognized by

the control processor and can be added or removed at any time.

IPCP Pro Control Processors with AV LAN provide a secure network dedicated for the connection and isolation of AV devices.

This guide provides instructions for an experienced installer to install an IPCPPro Series control processor and to create a basic

configuration.

Use Extron Toolbelt software to discover and manage the IPCPPro control processor and other Extron control products.

Configure the control processor using Extron Global Configurator®software running in Global Configurator Professional

(GCProfessional) or Global Configurator Plus (GC Plus) mode, or program the control processor using Extron Global Scripter®(GS).

The IPCP integrates seamlessly with Extron GlobalViewer®Enterprise (GVE) software and Extron Control apps for remote control

applications. These control processors support multiple TouchLink®Pro touchpanel interfaces over a standard Ethernet network.

Global Configurator and other useful software applications are available at www.extron.com.

Setup Checklist: How to Proceed With Installation

Get Ready

Familiarize yourself with the features of the control processor (see Front Panel Features — Models Without AV LAN on

page4, Front Panel Features — Models With AV LAN on page5, Rear Panel Features — Models Without AV LAN

on page6, and Rear Panel Features — Models With AV LAN on page7) and of any TouchLinkPro touchpanels that

will be part of the system.

Download and install the latest version of the following:

• Toolbelt software — for discovering the control processor and other control products on the network, for managing

core settings, and for upgrading firmware when needed.

• Global Configurator (GC) software — for configuring the control system.

• Global Scripter software — for programming the control processor (as an alternative to GC)

• GUI Designer software — for designing layouts for Extron TouchLinkPro touchpanels and third party touch interfaces

• IPLinkPro device drivers — for use with GC, to make control of AV devices possible

• IR Learner Pro software — for use with models that have IR receiver ports. Use this to create your own IR drivers using

the remote control of an AV device, if drivers are not already available from Extron

All are available from www.extron.com (see Locating Software, Firmware, and Driver Files on the Extron Website on page15).

Obtain network information for the unit from the network administrator. You also need the following details for each IPLinkPro

device:

DHCP setting (on or off) Subnet mask Username

Device (IPCP Pro, TouchLinkPro, IPLPro) LAN IPaddress Gateway IP address Passwords

AVLAN IPaddress (for models with AV LAN)

Write down the MAC address of each network interface on each IPLinkPro device to be used.

Obtain model names and setup information for devices the IPCP will control.

Using a dedicated AVLAN allows you to separate device control and

traffic from a corporate or campus communication network and to

safeguard AV systems from outside intrusion or interference.

IPCP Pro Series • Setup Guide (Continued)

Each control processor comes with a factory-installed Secure Sockets Layer (SSL) security certificate. If you intend to install

a different SSL certificate, contact your IT department to obtain the certificate or for instructions on how to obtain one. See

“Secure Sockets Layer (SSL) Certificates” in the IPCPProSeries User Guide for requirements and guidelines regarding SSL

certificates.

Mount and Cable All Devices

Mount the unit to a rack or furniture (see Mounting on the next page).

Cable devices to the control processor (see Cabling and Features on page 8).

Connect power cords and power on all the devices.

Set Up the Control Processor and Touchpanels for Network Communication

Connect the PC that you will use for setup, the LAN (or AV LAN) port of the control processor, and the touchpanels to the

same Ethernet network. For control processor LAN and AV LAN connections, see Control, Bidirectional — LAN and AV LAN

(Ethernet) on page9.

Start Toolbelt and use it to set the IP address, subnet, gateway IP address, DHCP status, and related settings. See the

flowchart in Network Communication Setup on the next page.

NOTE: When setting up DHCP during network configuration or if using a host name instead of an IP address, the user

must enter a qualified host name (Username.HostName.Domain). For example: somename.extron.com.

Configure or Program the Control Processor and Touchpanels

The most basic steps are outlined below in the recommended order.

NOTE: See the Toolbelt Help File, Global Configurator Help File, Global Scripter Help File, and GUI Designer Help File as

needed for step-by-step instructions and detailed information. The help file for GC includes an introduction to the software

and how to start a project and configuration.

If TouchLinkPro or third party touchpanels are part of the system, start and use GUI Designer to design, save, and build the

graphical user interface (GUI) layout for the touchpanels.

NOTE: To redeem (activate) a LinkLicense®, go to www.extron.com//llredeem and follow the online instructions.

Using GC, create a new GCProfessional or GCPlus project and configure the control processor and other IP Link Pro

devices. The configuration tells the control processor:

• How its ports function • What to monitor

• How to control other products • When to do things

• Which touchpanels to interact with • Whom to notify, how, and under what circumstances

Configure ports on the control processor.

Select device drivers and link them to each serial, IR/serial, or Ethernet port.

Select settings (serial protocol, relay behavior, digital I/O or flex I/O settings) as needed.

Add eBUS devices and set them up:

Ensure that the hardware address set on each device is distinct and matches the address used in the configuration.

Assign button functions as desired.

Set up monitors, schedules, macros, and local variables.

Add touchpanels and set them up:

• Add the GUI configuration for each touchpanel to the GC project using Global Configurator.

• Assign any appropriate functions, monitors, or schedules to the touchpanels and their buttons.

If not using GC Professional or GC Plus, use Global Scripter to program the control system as desired.

Program ports on the control processor.

• Program each serial, IR/serial, or Ethernet port.

• Program relay behavior, digital I/O, and flex I/O settings as needed.

Add eBUS devices and set them up:

• Ensure that the hardware address (eBUS ID) set on each device is distinct and matches the address programmed

for it in the IPCP.

• Program button functions as desired.

Rev. E: Updated

wording regarding

adding touchpanel

GUIs.

Add touchpanels and set them up:

• Upload the GUI configuration for the touchpanels.

• Program the touchpanel buttons.

Save and build the project.

Upload the system configuration to the control processor.

Test and Troubleshoot

Test the system (see the IPCPProUser Guide for an outline of the system testing procedure).

Make adjustments to wiring or configuration as needed.

Network Communication Setup

Network setup is essential prior to configuration. Use the following flowchart as a guide to setting up the control processor for

network use.

Open the Toolbelt software from within

Global Congurator (GC Professional or

GC Plus mode) or as the stand-alone

application.

Start Device Discovery.

Toolbelt displays a list of all Extron control

devices connected to the network.

Using the MAC address, locate the desired

control processor in the list and select it.

Network Communication Setup

Connect the PC and the LAN port or AV LAN

port of the control processor to

the same network.

Apply power to all devices.

For each network interface

(LAN, or LAN and AV LAN), use the Set IP

feature in Toolbelt or use the

Toolbelt Manage > Network Settings tab

feature to enter the IP address and

subnet address, then congure other

network settings as needed.

Figure 1. Network Setup

Mounting

Securely mount the control processor and other devices and attach cables using the wiring section (see Cabling and Features

on page8) as a wiring guide. Optional 1U rack shelves and furniture mounting bracket kits are available for use with the control

processor. Read the instructions and UL guidelines that come with the rack shelf or mounting kit for installation procedures. See the

product-specific page at www.extron.com for a list of compatible accessories for mounting your control processor.

IPCP Pro Series • Setup Guide (Continued)

Panels and Locations of Features

Location and quantity of LEDs and corresponding connectors vary by model, but the functions and port wiring are identical

across models for each port type.

Front Panel Features — Models Without AV LAN

IPCP PRO 350

1000

LINK

ACT

LAN

123

LIMIT

RIR

RTS

CTS

COM

IR/SERIAL RELAYS FLEX

I/O

S LIMIT

eBUS

SWITCHED

12 VDC 1000

LINK

ACT

IPCP PRO 550

OVER

43 12345678

OVER

5678

3 4

2134

5678

2134

COM

I/O RELAYS

IR/S

2231

LIMIT

eBUS

OVER

CTS

RTS

LIMIT

eBUS

OVER

RTS

CTS

COM

I/O RELAYS

IR/S

1000

LINK

ACT

IPCP PRO 250

LIMIT

eBUS

OVER

CTS

RTS

COM

I/O RELAYS

IR/S

2231

NOTE: Numbers adjacent to LEDs correspond to

the like-numbered rear panel ports.

Switched

12 VDC

LEDs

COM (Serial)

LEDs

COM

(Serial)

LEDs

IR/Serial

LEDs

IR/

Serial

LEDs

Flex I/O

LEDs

Reset

Button

(recessed)

Reset Button

(recessed)

eBUS LEDs

eBUS

LEDs

IR Receiver

Relay

LEDs

Relay

LEDs

eBUS LEDs

IR Receiver

IR Learning

Angle and

Distance

LAN/

Network

LEDs

Digital I/O LEDs

IR Receiver

LAN/

Network

LEDs

Digital

I/O

LEDs

Power

LED

Power

LED

Power

LED

1 2 3

4 5 6

7 8

2–12"

(4–30 cm)

15˚ 15˚

IPCP Pro Embedded Control Processor Without AV LAN

(within another device)

NOTES:

• For reset mode information, see the IPCPProSeries User Guide.

• The Reset button and power LED for the IPCPPro embedded control processors are located next to the rear panel

connectors.

• The embedded control processors do not have an IR learning sensor.

Figure 2. Front Panels: IPCP Pro Series Rack Mountable Models

Without AV LAN

Front Panel Features — Models With AV LAN

This section shows the front panels of a couple representative AV LAN models, not all models.

IPCP PRO 360

1000

LINK

ACT

AV LAN

123

LAN

COM

I/O RELAYS

IR/S

2231

LIMIT

eBUS

OVER

CTS

RTS

ERROR

LINK

BUSY

COM (Serial)

LEDs

IR/Serial

LEDs

Reset

Button

(recessed)

eBUS LEDs

Receiver

Relay

LEDs

LAN

LEDs

AV LAN

LEDs

Digital I/O

LEDs

Power

LED

Figure 3. IPCPPro360 Front Panel

LIMIT

eBUS

OVER

CTS

RTS

ERROR

LINK

BUSY

COM

I/O RELAYS

IR/S

12 121

COM

(Serial)

LEDs

IR/

Serial

LEDs

eBUS

LEDs

Relay

LEDs

Digital

I/O

LEDs

IPCP Pro Embedded Control Processor With AV LAN

(within another device)

Figure 4. Figure 3: IPCP Pro Embedded Control Processors With AV LAN — Front Panel

Rev. E: Added

IPCP Pro 355M

front panel.

IPCP Pro Series • Setup Guide (Continued)

Rear Panel Features — Models Without AV LAN

LAN

123

GTx Rx GTx Rx

COM 2 COM 3

RELAYS

2143CC

LAN

eBUS

FLEX I/ORELAYSIR/SERIALCOM12 VDC

Tx Rx GTxRxG Tx Rx GTxRxG SGSG SGSG

SGSG SGSG

RTSCTS

IPCP PRO 550

Tx Rx GTxRxG Tx Rx GTxRxG

RTSCTS

1.2A MAX

SWITCHED 12 VDC

40W MAX TOTAL

COM 1

GTx Rx

RTS CTS

IR/SERIAL

POWER

12V

1.0A MAX

1234G

DIGITAL I/O

eBUS

+V +S -S G

PWR OUT = 6W

GTx Rx GTx Rx

COM 2COM 3

RELAYS

2143CC

COM 1

GTx Rx

RTS CTS

IR/SERIAL

1234G

DIGITAL I/O

eBUS

+V +S -S G

PWR OUT = 6W

3 4

1 1 2 3 7

4 5 6

2 1 2

5 6

3 4

7 8

1 2

5 6

3 4

783214G

+V +S -S G

PWR OUT = 12W

100-240V ~ 50-60Hz

IPCP PRO 350

PWR OUT = 6W

VCG

VOL

POWER

12V

1.0A MAX

Tx Rx

RTSCTS

COM 1

12 4G

DIGITAL I/O

Tx Rx

COM 2

-S+V +S G

eBUS

C12

RELAYS

IR/S

LAN

IPCP PRO 250

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

DDDDE

EEE

PCP Pro 550

PCP Pro 350

DDDDEEEE

IPCP Pro 250

AAAA

AAA

CCCBBBBDDDDEEEEHHHH

III

DDDEEEEIIIIIIII

KKKK

JJJ

FFF

GGGG

GGG

FFFGGGG

LLL

LLLL

MMM

JJJJFFFFGGGG

IPCP Pro Embedded

Cont

rol Processor

Withou

t AV LAN

ithin another

vice)

Figure 5. IPCPPro Control Processors Without AV LAN —Rear Panels

APower input connector (external power supply) HFlex I/O ports (digital input/output or analog input)

BPower input connector (internal power supply) IDigital I/O ports (digital input/output)

cSwitched 12 VDC power output ports JeBUS ports

D3-pole COM ports (RS-232-only) KVolume control port

E5-pole COM ports (RS-232/RS-422/RS-485) LLAN connectors and LEDs (Ethernet)

FIR/serial output ports MMAC address label

GRelay ports

Rear Panel Features — Models With AV LAN

This section shows rear panels of some representative models with AV LAN.

PWR

PoE+ OUT PoE+ OUT

GTx Rx GTx Rx

COM 2 COM 3

RELAYS

2143CC

AV LAN

LAN

COM 1

GTx Rx

RTS CTS

IR/SERIAL

1234G

DIGITAL I/O

eBUS

+V +S -S G

PWR OUT = 6W

IPCP PRO 360

PWR OUT = 6W

VCG

VOL

POWER

12V

1.0A MAX

Tx Rx

RTSCTS

COM 1

12 4G

DIGITAL I/O

Tx Rx

COM 2

-S+V +S G

eBUS

C12

RELAYS

IR/S

LAN

50-60 Hz

100-240V ~ 1.5A MAX

LAN

GTx Rx GTx Rx

COM 2COM 3

RELAYS

2143CC

COM 1

GTx Rx

RTS CTS

IR/SERIAL

1234G

DIGITAL I/O

eBUS

+V +S -S G

PWR OUT = 6W

AV LAN 2

AV LAN 1

AV LAN 3

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

IPCP LAN

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

IPCP AV LAN

DDDDE

EEE

PCP Pro 360

DDDDEEEE

IPCP Pro 255

AAAA

III

LLLIIII

KKKK

JJJ

FFFGGGG

NNN

LLLL

MMMM

MMM

BBBB

DDDEEEEIIII

LLLLNNNNJJJJFFFFGGGG

IPCP Pro Embedded

Cont

rol Processor

With

AV LAN

ithin another

vice)

Figure 6. IPCP Pro Control Processors With AV LAN — Rear Panels

APower input connector (external power supply) IDigital I/O ports (digital input/output)

BPower input connector (internal power supply) JeBUS ports

D3-pole COM ports (RS-232-only) KVolume control port

E5-pole COM ports (RS-232/RS-422/RS-485) LLAN connectors and LEDs (Ethernet)

FIR/serial output ports MMAC addresses

GRelay ports NAV LAN connector and LEDs (Ethernet), some with PoE+

and PoE+ LEDs

The following ports are not shown in figure 6 but are available in some AV LAN models such as the IPCPPro555.

cSwitched 12 VDC power output ports HFlex I/O ports (digital input/output or analog input)

IPCP Pro Series • Setup Guide (Continued)

Cabling and Features

Attach cables using the following wiring diagrams as a guide. Full details are available in the IPCPPro Series User Guide.

ATTENTION:

• Installation and service must be performed by experienced personnel.

• L’installation et l’entretien doivent être effectués par du personnel expérimenté.

Power Input — External

POWER

12V

x.xA MAX R

Ground all devices.

External

12 VDC

Power Supply

+12 VDC input

– Return

Ridged

Smooth

power

Front Panel

Power Input, External Power Supply

• Front panel LED ( ) blinks during

boot-up and remains lit when the

IPCP is powered and operational.

• Connect to

included 12 VDC

power supply.

NOTE:

Check the polarity of the power

supply before connecting it to the IPCP.

Ridged

Smooth

Tie Wrap

3/16"

(5 mm)

Max.

Power Input — Internal

1.2A MAX

100-240V 50-60Hz

Power Input, Internal Power Supply

• Front panel LED ( ) blinks

during boot-up and remains lit

when the IPCP receives power.

• Connect to 100 to

240 VAC.

Rear

Panel

Front Panel

Power Output — Switched 12 VDC Power Output

LIMIT

SWITCHED

12 VDC

OVER

12 VDC

SWITCHED 12 VDC

40W MAX TOTAL

3 4

1 2

Lights if total power drawn

is 41-46 watts.

Lights if total power drawn

exceeds 47 watts.

Power output shuts off

until the user corrects the

overload.

Switched 12 VDC

Power Output

• Total output for all four ports

combined:

12 VDC, 40 watts (max.)

• Corresponding front panel

green LEDs ( ) light when

power is available at each port.

3/16"

(5 mm)

Max.

Rear

Panel

Front

Panel

Tie Wrap

Power Output — PoE+

The IPCPPro360 can output PoE+ on AV LAN ports 2 and 3. For details, see the PoE+ output information on page 11.

ATTENTION:

• Always use a power

supply supplied or

specified by Extron. Use

of an unauthorized power

supply voids all regulatory

compliance certification and

may cause damage to the

supply and the unit.

• Utilisez toujours une source

d’alimentation fournie par

Extron. L’utilisation d’une

source d’alimentation non

autorisée annule toute

certification de conformité

réglementaire et peut

endommager la source

d’alimentation que l’unité.

Rev. E: replaced

isometric power

supply with

orthogonal version.

Updated French

translation of 2nd

paragraph.

Control, Bidirectional — Serial (COM)

GTx Rx GTxRxG

RTS

Tx Rx GTxRxG

RTSCTS

CTS

COM 1

GTx Rx

RTS CTS

IAL

1 7

GTx Rx Tx Rx

COM 2 COM

REL

COM

RTS

CTS

COM

12345678

COM

231

CTS

RTS

NOTE: If you use cable that has a drain wire, tie the drain wire to ground at both ends.

Projector, Panel

Display, PC, or Other

RS-232, RS-422, or

RS-485 Device

RS-232-

Controllable

Device

Receive (Rx)

Transmit (Tx)

Transmit

Receive Receive (Rx)

Transmit (Tx)

Ground

Request to send

Clear to send

Transmit

Rx Receive

CTS

RTS

GGround

Strip wires

3/16" (5 mm) max.

COM

Front Panels

5-pole COM

(RS-232, RS-422, RS-485)

3-pole COM

(RS-232)

Select protocol via software.

COM port default protocol:

• 9600 baud

• 8 data bits • 1 stop bit

• no parity • no ow control

NOTE: The 5-pole COM ports support both

hardware and software ow control.

The 3-pole COM ports support software

ow control only.

Serial (COM) Ports

Rear

Panels

Heat Shrink

To 3-pole

COM port

To 5-pole

COM port

Heat Shrink

Over Shield Wires

or or

RTS =

Request to Send

CTS = Clear to Send

Tx = Transmitting Data

Rx = Receiving Data

RS-232

Ground

RTS

CTS

RS-422

Tx-

Rx-

Ground

Tx+

Rx+

RS-485

Ground

5-pole COM Pin Conﬁgurations

Data-

(pins 1 & 2

tied together)

Data+

(pins 4 & 5

tied together)

1(Tx)

2(Rx)

3(G)

4(RTS)

5(CTS)

Control, Bidirectional — LAN and AV LAN (Ethernet)

Default port IP addresses and recommended connections vary depending on whether or not the IPCP model includes AV LAN

ports.

Models without AV LAN — LAN ports

1000

LINK

ACT

LAN

123

LAN

RJ-45

Connector

Insert

Twisted Pair Wires

Pins: 12345678

Rear Panel,

Rack Mount

Models

Front Panel,

Rack Mount

Models

NOTE: IPCPs with more than one LAN port function as

multiport, unmanaged network switches so you can

connect additional devices to the same network.

Ethernet

Link

LED

Activity

LED

1000 Mbps

Connection

Network is

active.

Data is being

sent/r

eceived.

TCP/IP

Network

LAN (Ethernet) — Models Without AV LAN

Default protocol, public ports: Default login

credentials:

• Username:

admin

• Password:

extron

• IPCP IP address: 192.168.254.250

• Gateway IP address: 0.0.0.0

• Subnet mask: 255.255.255.0

• DNS address: 127.0.0.1

• DHCP client: off

• Link speed and duplex level: autodetected

• Data rates: 10/100/1000Base-T

3/16"

(5 mm)

Max.

7/8"

(22 mm)

Heat Shrink

on Outer

Jacket to

Inner

Conductor

Transition

Extron

STP 20-2P Cable

TIP:

STP 20-2P

cable, shown

at left, is

recommended

for these

connections.

For best

results,

insulate the

common or

drain wires

using heat

shrink.

IPCP Pro Series • Setup Guide (Continued)

Models with AV LAN — LAN ports

1000

LINK

ACT

LAN

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

-A

YY-YY-Y

Y-

N: ###

###

E###

LAN

PWR

E+ OU

oE+

AV L

MAC: 00-05-A6-YY-YY-YY

S/N: ####### E######

00-05-A6-XX-XX-XX

IPCP LAN

MAC: 00

-A

#### E###

5-A6-XX-XX-

P AV LA

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

12345678

Rear

Panels

Front

Panels

NOTE: IPCPs with more than one LAN or AV LAN port function as multiport, unmanaged

network switches so you can connect additional devices to the same network.

Link

LED

Activity

LED

1000 Mbps

Connection

Network is

active.

Data is being

sent/r

eceived.

LAN (Ethernet) —

Models With AV LAN

Default protocol, LAN

ports:

• LAN IP address:

192.168.253.250

• Gateway IP address:

0.0.0.0

• Subnet mask:

255.255.255.0

• DNS address: 127.0.0.1

• DHCP client: off

• Link speed and duplex

level: autodetected

• Data rates:

10/100/1000Base-T

Default login

credentials:

• Username: admin

• Password: extron

Ethernet

Corporate

TCP/IP

Network

Ethernet

Corporate

TCP/IP

Network

Models with AV LAN — AVLAN ports

1000

LINK

ACT

AV LAN

123

LAN

-A

XX-XX-X

X-

N: ###

###

E###

MAC: 00-05-A6-YY-YY-YY

S/N: ####### E######

LAN

PWR

PoE+ OUT PoE+ OUT

AV LAN

-05

-A

N: ##

#### E#####

00-

5-A6-XX-X

-XX

PCP LAN

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

IPCP AV LAN

RJ-45

Connector

Insert Twisted

Pair Wires

Pins: 12345678

NOTE: IPCPs with more than one LAN or AV LAN

port function as multiport, unmanaged network

switches so you can connect additional

devices to the same network.

Rear

Panels Front

Panels

Link

LED

Activity

LED

1000 Mbps

Connection

Network is

active.

Data is being

sent/received.

AV LAN (Ethernet)

Default protocol,

AV LAN:

• IP address:

192.168.254.250

• Subnet mask:

255.255.255.0

• DNS address: 127.0.0.1

• DHCP client: off

(disabled)

• DHCP server off

(disabled)

• Link speed and duplex

level: autodetected

• Data rates:

10/100/1000Base-T

Default login

credentials:

• Username: admin

• Password: extron

Ethernet

AV LAN DHCP Server

The AV LAN DHCP Server is disabled by default. It can be enabled to dynamically assign

IP addresses to DHCP clients on the AV LAN.

Network

Default protocol, AV LAN when

DHCP server is enabled:

• DHCP server IP address: 192.168.254.1

• Subnet mask: 255.255.255.0

• DNS address: 192.168.254.1

• DHCP dynamic address range for client

devices: 192.168.254.100 -

192.168.254.149

• Maximum served addresses when

DHCP server is enabled: 50

• DHCP client address lease time: 24 hours.

To use DHCP in the AV LAN:

1. Using Toolbelt, enable the DHCP server

for the AV LAN within the control

processor (see the software or

programming help le for details).

2. Enable DHCP on each client AV device

(see the user guide for each product).

3. Connect client AV devices to the AV LAN.

Andere Handbücher für IPCP Pro Series

Inhaltsverzeichnis

Andere Extron electronics Computerhardware Handbücher

Extron electronics

Extron electronics Network Device PIP 444 Bedienungsanleitung

Extron electronics

Extron electronics HAE 100 4K Bedienungsanleitung

Extron electronics

Extron electronics DVI Output Card Bedienungsanleitung

Extron electronics

Extron electronics WindoWall Pro Series Bedienungsanleitung

Extron electronics

Extron electronics EDID 101D Bedienungsanleitung

Extron electronics

Extron electronics DMP 64 Bedienungsanleitung

Extron electronics

Extron electronics Annotator 300 Bedienungsanleitung

Extron electronics

Extron electronics IPL M PDP-ES Montage- und Bedienungsanleitung

Extron electronics

Extron electronics DMP 44 LC Bedienungsanleitung

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Bedienungsanleitung

Extron electronics

Extron electronics IPL Pro Series Bedienungsanleitung

Extron electronics

Extron electronics PIP 422 Bedienungsanleitung

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Bedienungsanleitung

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Bedienungsanleitung

Extron electronics

Extron electronics StudioStation 100 Bedienungsanleitung

Extron electronics

Extron electronics UCS 601 Bedienungsanleitung

Extron electronics

Extron electronics IPL Pro Series Bedienungsanleitung

Extron electronics

Extron electronics Dual Window Multi-Graphic Processor MGP 462D Bedienungsanleitung

Extron electronics

Extron electronics UCS FT 901 Bedienungsanleitung

Extron electronics

Extron electronics Annotator Bedienungsanleitung

Extron electronics

Extron electronics AXP 64 C AT Bedienungsanleitung

Extron electronics

Extron electronics IPCP 505 Bedienungsanleitung

Extron electronics

Extron electronics DMP Plus Series Bedienungsanleitung

Extron electronics

Extron electronics SMP 351 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung