Extron electronics DMP 44 LC Bedienungsanleitung

Product Category

DMP 44 LC • Setup Guide

The Extron DMP 44 LC Digital Matrix Processor is a compact 4x4 audio matrix processor featuring a digital signal processing

(DSP) platform for audio signal routing, processing, and control. The DMP 44 LC features four line level inputs and outputs,

all balanced or unbalanced. It offers several audio DSP tools for mixing, routing, and room optimization with quick and

intuitive conﬁguration using the DSP Conﬁgurator™ Software.

NOTE: For full installation, conﬁguration, and operation details, see the DMP 44 LC User Guide available at

www.extron.com.

Rear Panel Features and Connections

a12 VDC power connector eRS-232 connector

bPower/Reset LED fDigital input connector

cLine input connectors (1 – 4) gReset button

dLine output connectors (1 – 4)

Installing the DMP 44 LC

1. Disconnect power from all equipment.

2. (Optional) Mount the unit to a rack or furniture.

3. Connect the audio input. Connect up to four balanced or

unbalanced mono line level input devices to line input

connectors cabove (see the wiring diagram on the right).

4. Connect the audio output. For balanced or unbalanced

audio output, connect up to four output devices to line output

connectors dabove (see the wiring diagram on the right).

5. Connect a control device. Connect a host device, such as a

computer, to one of the following DMP 44 LC ports to

conﬁgure and control the DMP via Simple Instruction Set (SIS™)

commands.

zRS-232 port (rear panel) — Connect a host device

to the Tx, Rx, and _(ground) pins of this 6-pole

captive screw connector (e). The default baud rate

for this port is 38400 baud, 1 stop bit, no parity,

8 data bits, and no ﬂow control (see the wiring diagram

on the right).

zCong port (front panel) — Connect a USB cable (USB-A to

Mini-B) between a USB port on your computer and this

port (aon the front panel illustration shown on the right).

6. Digital input connector. Up to three

conﬁgurable input ports (see fon the

rear panel diagram) allow connection

to various digital devices including

motion detectors, alarms, buttons,

photo (light) sensors, and temperature

sensors. This connector shares a

ground pin with the RS-232 connector (see the wiring diagram above).

Both the RS-232 and digital input connectors may be used simultaneously by using

a 6-pin captive screw connector with two wires sharing the same ground connector

(see the diagram on the right).

7. Reset button. The recessed reset button is used to access various modes of

resets. The green power LEDs on both the front and rear panels indicate

the reset mode that was accessed. The reset modes are detailed in the user guide.

BalancedUnbalanced

Tip

Ring

Sleeve

Tip

Sleeve

Receive (Rx)

Transmit (Tx)

Ground ( )

Bidirectional

RS-232

Device

Ground ( )

Receive (Rx)

Transmit (Tx)

RxTx

Do not tin

the wires!

DMP 44 LC

RESET

Tx Rx 1 2 3

RS-232 DIGI IN

INPUTS

OUTPUTS

POWER

12V

0.3A MAX

1 2 3 4 5 6

DMP 44 LC

DIGITAL MATRIX PROCESSOR

CONFIG

Audio Output Wiring

CAUTION

For unbalanced audio, connect the

sleeve to the ground contact.

DO NOT connect the sleeve to the

negative (−) contacts.

Unbalanced Output

Tip

Sleeve

NO Ground Here

Balanced Output

Tip

Sleeve

Ring

Audio Input Wiring

Balanced Input

Tip

Sleeve

Ring

Tip

Sleeve

Unbalanced Input

RS-232 DIGI IN

Tx Rx 1 2 3

Do not tin the wires!

RS-232

Tx Rx

DIGI IN

68-1938-50 Rev. A10 11

8. Connect power to the DMP 44 LC by connecting the included 12 VDC

external power supply to the rear panel power connector (see aon the

previous page). The wiring diagram is shown on the right.

9. Install the software. There are no hardware controls for the DMP 44 LC.

All conﬁguration and control is done via software. The control software,

DSP Conﬁgurator, is available on the included DVD or from the Extron

website at www.extron.com (see the following sections). The control

software help ﬁle contains all operation descriptions.

Software and Manual Download from the DVD

1. Insert the disk provided into the DVD ROM drive of the computer. If the setup program

does not start automatically, run Launch.exe from the DVD ROM directory using Windows

“My Computer.” The opening screen will appear with the following tabs:

2. For the user guide, select the Manuals tab, then select the DMP 44 LC User Guide from the list of available

documentation. The manual, in PDF format, will open in the browser window or can be downloaded to the hard drive

for future reference.

3. To download the DSP Conﬁgurator program, select the Software tab.

4. From the Downloads page, on the DSP Conﬁgurator row (the downloads are listed in alphabetical order), select

Install.

5. Choose Run and the DSP Conﬁgurator will install. In most cases it is best to accept the default installation suggestions.

6. When the DSP Conﬁguration program completes installation, the USB driver must be installed. Whether planning to use

the USB conﬁguration port or not, it is recommended to install it. Click Next on the USB Driver Installer and follow the

on-screen instructions.

7. When the USB driver installation completes, remove the DVD from the drive and reboot the computer.

8. Launch the DSP Conﬁgurator program from the Extron Electronics group in the Start menu. Select

“DMP 44 LC.” The DSP Conﬁgurator help ﬁle contains details about using the software.

Software and Manual Download from the Website

1. Using any internet browser, go to www.extron.com.

2. From the Extron home page, select the DMP 44 LC from the Product Shortcuts drop-down menu.

3. Select the Downloads tab on the DMP 44 LC product page.

4. Select the User Guide from the list of available documentation and click on it to either view or download it to the hard

drive for future reference.

5. To download the control software, on the Downloads tab select DSP Configurator.

6. The link navigates to the selected software download page. Fill out the form, then download the software to the hard

drive.

7. When the download is complete, locate the ﬁle (dsp_conﬁgurator_Vxxx.exe) on the hard drive and double-click on

this ﬁle. The ﬁle is a self-executing installation program. In most cases it is best to accept the default installation

suggestions.

8. Proceed to Step 6of the "Software and Manual Download from the DVD"section above.

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.863.1794

+1.714.491.1517 FAX +1.919.863.1797 FAX

Extron Europe

+800.3987.6673

(Inside Europe Only)

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

(Inside Asia Only)

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+4000.398766

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

Inside India Only

+91-80-3055.3777

+91 80 3055 3737 FAX

SECTION A–A

Power Supply

Output Cord

Ridges

Smooth

Ridges

Smooth

2-Pole Orange

Captive Screw

Connector

(12V)

Tie Wrap

3/16”

(5 mm) Max.

Andere Handbücher für DMP 44 LC

Andere Extron electronics Computerhardware Handbücher

Extron electronics

Extron electronics DTP3 T/R 301 Bedienungsanleitung

Extron electronics

Extron electronics SMP 300 Series Bedienungsanleitung

Extron electronics

Extron electronics MTP 15HD RS Series Bedienungsanleitung

Extron electronics

Extron electronics Annotator 300 Bedienungsanleitung

Extron electronics

Extron electronics Dual Window Multi-Graphic Processor MGP 462 Bedienungsanleitung

Extron electronics

Extron electronics IPL Pro Series Bedienungsanleitung

Extron electronics

Extron electronics IPCP Pro Series Bedienungsanleitung

Extron electronics

Extron electronics DMP Plus Series Bedienungsanleitung

Extron electronics

Extron electronics Scalable Multi-Graphic Videowall Processors MGP 464W... Bedienungsanleitung

Extron electronics

Extron electronics DMP 64 Plus Bedienungsanleitung

Extron electronics

Extron electronics Annotator 300 Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 202 Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 202 Bedienungsanleitung

Extron electronics

Extron electronics DMP 44 LC Bedienungsanleitung

Extron electronics

Extron electronics Quantum Ultra Series Bedienungsanleitung

Extron electronics

Extron electronics HAE 100 4K Bedienungsanleitung

Extron electronics

Extron electronics DMP 128 FlexPlus Bedienungsanleitung

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Bedienungsanleitung

Extron electronics

Extron electronics SC 210 Bedienungsanleitung

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Bedienungsanleitung

Extron electronics

Extron electronics EDID 101D Bedienungsanleitung

Extron electronics

Extron electronics UCS FT 901 Bedienungsanleitung

Extron electronics

Extron electronics Network Device PIP 444 Bedienungsanleitung

Extron electronics

Extron electronics IPL M PDP-ES Montage- und Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung