Extron electronics DDX 102 Tx Bedienungsanleitung

DDX 102 Tx/Rx • Setup Guide

This guide provides basic instructions for an experienced installer to set up and operate the DDX 102 Tx/Rx.

NOTES:

• Refer to www.extron.com for the product specifications.

• The DDX 102 extenders are not compatible with any Extron fiber optic products.

• The DDX 102 extenders do not support transmission of HDCP content video signals.

Description

The Extron DDX 102 Tx/Rx are ber optic transmitter and receiver units that can extend Dual Link DVI signals using two

multimode ber cables.

The DDX 102 Tx/Rx units can extend Dual Link DVI video signals (2560x1600 @ 60 Hz) up to 1,640 feet (500 m) using two

mutimode ber optic cables. The units can also extend Single Link DVI signals (1920x1200 @ 60 Hz) up to the same maximum

distances as Dual Link DVI.

The transmitter plugs directly into the source device and the receiver plugs directly into the display device.

Front Panel and Side Panel Features

APower LED — The blue LED on the transmitter and receiver indicates the unit is

receiving power.

BStatus LED — The blue LED on the bottom provides the status of EDID learning

on the transmitter. The Status LED indicates power on the unit simultaneously

with the top Power LED. On the receiver, this is simply an additional power status

LED.

CEDID Record button (transmitter only) — Iinitiates the EDID recording process.

DThumb screws — Two thumb screws, one on each side, fasten the device onto

the DVI connector of a product.

CLASS 1 LASER PRODUCT

5VDC 1 2

STATUS

Top Panel Features

EDVI-D Dual Link connector — The transmitter and receiver both have a DVI-D Dual Link connector.

Bottom Panel Features:

FPower Input — The transmitter and receiver both have a DC jack for power input on the top left

corner of the bottom panel.

GLC connectors — The transmitter and receiver both have two LC fiber optic connectors or

receptacles as interconnects for fiber optic cables.

NOTE: Only one fiber optic cable is needed for DVI Single Link video signals.

Installation and Operation

NOTE: Perform EDID Learning operation first. After EDID is set up, follow the instructions for Connection.

CAUTION:

• This unit outputs continuous invisible light, which may be harmful to the eyes; use with caution. For additional safety,

plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.

• L’appareil émet une lumière invisible en continu, à utiliser avec précaution. Pour une sécurité renforcée, associez les

bouchons anti-poussière à l’ensemble émetteur/récepteur optique lorsque le câble fibre optique est débranché.

DDX 102 Tx/Rx • Setup Guide (Continued)

EDID Learning

The transmitter features the ability of EDID emulation. It has the ability to record and store

EDID from the display. To do so, follow these steps:

1. Turn on the display device.

2. Connect the 5V power supply to the transmitter. The Power LED turns on.

CLASS 1 LASER PRODUCT

5VDC 1 2

STATUS

ATTENTION:

• Always use a power supply provided by or specified by Extron. Use of an unauthorized power supply voids all

regulatory compliance certification and may cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. L’utilisation d’une source

d’alimentation non autorisée annule toute certification de conformité réglementaire, et peut endommager la source

d’alimentation et l’unité.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

The power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary

location, Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium or desk.

• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation dans les espaces d’aération

ou dans les cavités murales. La source d’alimentation doit être placée à proximité de l’équipement de traitement

audiovisuel Extron dans un emplacement ordinaire soumis à un degré de pollution de catégorie II, solidement fixée

au rack d’équipement d’une baie technique, d’un pupitre, ou d’un bureau.

• The installation must always be in accordance with the applicable provisions of National Electrical Code

ANSI/NFPA 70, article 75 and the Canadian Electrical Code part 1, section 16. The power supply shall not be

permanently fixed to building structure or similar structure.

• L’installation doit toujours être conforme aux dispositions applicables du Code américain de l’électricité (National

Electrical Code) ANSI/NFPA 70, article 75, et du Code canadien de l’électricité, partie 1, section 16. La source

d’alimentation ne devra pas être fixée de façon permanente à la structure de bâtiment ou à d’autres structures

similaires.

NOTE: Apply power to the display device and the transmitter every time EDID is stored.

3. With the transmitter disconnected from the display device, press and release the recessed EDID Record button on the left

side of the transmitter with a paper clip or similar tool. The blue Status LED blinks twice and the LED stays on.

4. Connect the transmitter to the display device. The blue Status LED stays

lit for about 8 seconds indicating that the EDID recording is in process.

After EDID is recorded, the blue Status LED stops lighting and remains off.

NOTE: The transmitter must remain connected to the display

device and the power supply for the entire time that the EDID

capture is taking place.

5. Disconnect the transmitter from the display device and connect it to the

DVI output of the source device.

NOTE: If the source provides 5 VDC power via Pin 14 of the DVI

output, the transmiter can be powered without an external power

supply.

CLASS1 L ASERPRO DUCT

5VDC 2 1

STATUS

Hi-resolution Displa

with DVI-D Input

DDX 102 Rx

CLASS1 LASER PRODU CT

5VDC

1 2

STATUS

PC with DVI-D Output

DDX 102 Tx

Connection

CLASS1 L ASERP RODUCT

5VDC

1 2

STATUS

CLASS1 L ASERPRODUCT

5VDC 2 1

STATUS

Hi-resolution Display

with DVI-D Input

PC with DVI-D Output

Multi Mode Fiber

(2)

Up to 500 m

(1,640’)

DDX 102 Tx DDX 102 Rx

1. Ensure that the source device is off, connect the transmitter to the DVI output of the source, and tighten the thumbscrews.

2. Ensure that the display device is on, connect the receiver to the DVI input of the display, and tighten the thumbscrews.

3. Using two LC fiber optic cables, connect port 1 of the transmitter to port 1 of the receiver and connect port 2 to port 2 as

shown in the image below at the right.

NOTE: If Single Link DVI is used, only fiber line 1 needs to be connected.

4. Using two LC fiber optic cables, connect port 1 of the transmitter to port 1 of

the receiver and connect port 2 to port 2 as shown in the image at right.

NOTE: If Single Link DVI is used, only fiber ine 1 needs to be

connected.

5. Connect the 5V power adapters to the transmitter and the receiver. The

Power LEDs turn on.

NOTE: The power adapter does not need to be connected to the

transmitter if the graphic source provides enough power to operate

the transmitter.

6. Turn on the source device and ensure that the Status LEDs on the

transmitter and receiver are on.

CLASS 1 LASER PRODUCT

5VDC 1 2

STATUS

CLASS 1 LASER PRODUCT

5VDC 2 1

STATUS

Fiber Line 2

Fiber Line 1

Troubleshooting

The display does not show an image

• Ensure that all plugs and jacks used by external power supplies are firmly connected.

• Ensure that the Power and Status LEDs for both the transmitter and receiver are lit.

• Ensure that the DVI ports are firmly plugged into the computer and display.

• Ensure that the transmitter and receiver are plugged properly to the computer and display.

• Ensure that the fiber optic cables are connecting the correct ports. Port 1 of the transmitter must be connected to port 1 of

the receiver. Port 2 of the transmitter must be connected to port 2 of the receiver.

• Ensure that the source device and output device are powered on and have booted up correctly.

• Ensure that the correct EDID information has been stored on the transmitter. When using the DDX 102 Tx/Rx for the first

time or if the display device is changed, it is essential to set up the EDID Minder™as described in steps 1 through 5 of EDID

Learning on page2 of this guide.

• Reset the system by unplugging and reconnecting the DVI connectors or the power jacks.

• Reboot the computer.

68-2276-50 Rev. B

10 20

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Screen is distorted or displays noise

• Ensure that the cable length does not exceed the specified cable lenghts for multimode or singlemode fiber optic extension.

• Ensure that the cables are high quality fiber optic cable and are terminated with securely fitting plugs.

• Ensure that the resolution is correctly set, using the EDID Minder (see Installation and Operation on page1).

• View the display properties of the source device to check the output resolution.

For Single Link, the resolution and refresh rate should not exceed 1920 x 1200 @ 60 Hz.

For Dual Link, the resolution and refresh rate should not exceed 2560 x 1600 @ 60 Hz.

• Reset the system by unplugging and reconnecting the DVI connectors or the power jacks.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extron electronics Extender Handbücher

Extron electronics

Extron electronics DTP HDMI 330 Bedienungsanleitung

Extron electronics

Extron electronics DVI 104 Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX 4G Tx VGA Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 330 Bedienungsanleitung

Extron electronics

Extron electronics XTP R HWP 201 Bedienungsanleitung

Extron electronics

Extron electronics FOX 3G HD-SDI Bedienungsanleitung

Extron electronics

Extron electronics DTP T/R DP 330 Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX Tx DVI Plus Bedienungsanleitung

Extron electronics

Extron electronics Tx-Rx Bedienungsanleitung

Extron electronics

Extron electronics DVI 104 Rx Bedienungsanleitung

Extron electronics

Extron electronics FOX T Plus MM Bedienungsanleitung

Extron electronics

Extron electronics DTP T DP 4K 330 Bedienungsanleitung

Extron electronics

Extron electronics CSVEQ 100 D Bedienungsanleitung

Extron electronics

Extron electronics UCS FT 901 Bedienungsanleitung

Extron electronics

Extron electronics FOX3 101 Bedienungsanleitung

Extron electronics

Extron electronics FOXBOX HDMI Bedienungsanleitung

Extron electronics

Extron electronics HDMI 230 D Bedienungsanleitung

Extron electronics

Extron electronics AKM MAAP Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX 4G Rx DVI Bedienungsanleitung

Extron electronics

Extron electronics FOX II T DP Bedienungsanleitung

Extron electronics

Extron electronics USB Extender Plus Series Bedienungsanleitung

Extron electronics

Extron electronics DTP T DWP 4K D Series Bedienungsanleitung

Extron electronics

Extron electronics DTP HDMI 4K D Series Bedienungsanleitung

Extron electronics

Extron electronics FOX3 SR 20 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung