Extron electronics ELink 100 Bedienungsanleitung

IMPORTANT:

Refer to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

IMPORTANT:

Go to www.extron.com for the complete

user guide,

installation instructions,

and

specifications bef

ore connecting the

oduct to the po

wer source.

eLink 100 • Setup Guide

The Extron eLink 100 T (transmitter) and eLink 100 R (receiver) units wirelessly extend HDMI signals up to 100 feet (30 m) with

a clear line-of-sight. Up to four receivers can be linked to a single transmitter, allowing the HDMI video from one source to be

output on multiple displays simultaneously.

This guide provides instructions for setting up and operating the eLink 100 transmitter and receiver (sold separately).

ATTENTION:

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 20 cm (7.9 inches) between the radiator and your body.

• Cet équipement est conforme aux limites de radiation de la FCC établies pour un environnement non géré. Il doit être

installé et contrôlé à une distance minimale de 20 cm (7,9 pouces) entre le radiateur et votre corps.

Mounting

The eLink 100 extenders can be mounted to a wall or a furniture surface, if needed. See the eLink 100 User Guide (available

online at www.extron.com) for mounting instructions.

Cabling

Transmitter Connections

AHDMI In connector — Connect an HDMI

cable between this port and the HDMI

output port of the video source device.

BIR Out connector — (Optional) Connect

the tip-ring-sleeve end of the provided

IR emitter to this IR Out connector. Use

the included adhesive tape to attach the

head of the IR emitter directly over the IR

receiver window of the source device.

IR remote signals are passed from the receiver to the IR Out connector on the transmitter. This allows the user to point the

remote toward the receiver (by the display) instead of the source device, should the source device be in a different location.

CPower input connector — Plug the external 5 VDC power supply into this 5 V jack to power the transmitter.

NOTES:

• Each eLink 100 power supply kit contains a set of four plugs for use in different outlet types. See the eLink 100

User Guide for instructions on replacing the plug, if needed.

• The USB mini-B port to the right of this connector is reserved for use by Extron service personnel.

Receiver Connections

AIR sensor — Receives IR commands

from the included IR remote control

unit and the IR remote of the source

device.

BUSB Power connector — Connect

the USB end of the provided 5 V

jack-to-USB adapter to this USB

mini-B connector (see image below).

Connect the other end of the adapter to the provided 5 VDC power supply.

To Power Supply To USB Power

Connector on

Receiver

DC Connector

on Power Supply

POWER

1.5A MAX

HDMI

HDMI OUT

Back Panel

HDMI IN IR OUT

POWER

SERVICE

1.5A MAX

NOTE: Snap the included ferrite bead onto

the power supply cable, at a distance of

3.25 inches (8.25 cm) from the end of the

DC connector (see image at right).

3.25 inches

(8.25 cm)

CHDMI Out connector — Connect an HDMI cable between this port and the HDMI input connector of the display device.

The eLink 100 On-screen Display (OSD)

When the receiver is powered and connected to the display device, the On-screen Display (OSD) appears. The OSD offers

instructions and feedback while registering the transmitter with the receiver (see the following section).

NOTE: For instructions on other OSD menus and features, see the eLink 100 User Guide.

Registering the Transmitter with the Receiver

To establish communication between the eLink 100 transmitter and receiver, the transmitter must be registered with the receiver.

After registration is performed at the initial setup, the transmitter and receiver connect automatically when booted.

The units can be registered using the eLink 100 remote control (see the eLink 100 User Guide for instructions) or using the register

buttons on the eLink 100 units (see the instructions below).

1. Connect and apply power to the transmitter, video source device, receiver, and display device.

NOTE: The registration process can be done without a video source device connected. In this case, a message appears

on the OSD, notifying you of a missing video source.

2. Press and hold the Register button

on the receiver top panel until the

following message appears on the OSD:

Please Activate Registration on

Transmitter Unit.

3. Press and hold the Register button on the

transmitter top panel until the following

message appears on the OSD: Adding

transmitter name. Press OK to

continue or Exit to cancel

4. Press the Register button on the receiver

to conrm. The message Adding

transmitter name... and a progress

bar appear on the OSD while registration is

completing.

NOTE: It may take up to 60 seconds for registration to complete. If the process is delayed more than 60 seconds, cycle

power on both units, then restart the registration process.

When registration is complete, the message and progress bar disappear from the display. The Link LED and the Video LED

light steadily, and the video is output on the display.

NOTE: For instructions on controlling the OSD menus and features using the eLink 100 remote, see the eLink 100 User

Guide.

Registering an Additional Receiver

Up to four receivers can be linked to a single transmitter. To register an additional receiver to the transmitter:

1. Power down all receivers except the one you are registering.

2. Perform steps 2 through 4 above (Registering the Transmitter with the Receiver).

3. When registration is complete, power on the other receivers to display the video on all monitors.

68-2662-50 Rev. B

10 14

Extron

eLINK 100 R

VIDEO

POWER

LINK

22 POWER

VIDEO

eLINK 100 T

LINK

RESET

Extron

Receiver

Transmitter

Andere Handbücher für eLink 100

Inhaltsverzeichnis

Andere Extron electronics Extender Handbücher

Extron electronics

Extron electronics USB Extender Tx Bedienungsanleitung

Extron electronics

Extron electronics FOX3 101 Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX Tx HDMI Bedienungsanleitung

Extron electronics

Extron electronics HFX 100 Tx Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX 4G Rx DVI Bedienungsanleitung

Extron electronics

Extron electronics DTP HDMI 330 Bedienungsanleitung

Extron electronics

Extron electronics UCS FT 901 Bedienungsanleitung

Extron electronics

Extron electronics Extension Kits AVTrac 4C Bedienungsanleitung

Extron electronics

Extron electronics DTP2 T 204 Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 301 Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 4K 230 D Series Bedienungsanleitung

Extron electronics

Extron electronics DTP T/R DP 330 Bedienungsanleitung

Extron electronics

Extron electronics FOXBOX Tx HDMI Bedienungsanleitung

Extron electronics

Extron electronics DTP HDMI 230 Bedienungsanleitung

Extron electronics

Extron electronics HDMI 230 D Bedienungsanleitung

Extron electronics

Extron electronics DTP T 3G-SDI 230 D Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX HDMI Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX 4G Tx VGA Bedienungsanleitung

Extron electronics

Extron electronics EDID 101H 4K Bedienungsanleitung

Extron electronics

Extron electronics DTP T DWP 4K 232 D Bedienungsanleitung

Extron electronics

Extron electronics FOX T UWP 302 Bedienungsanleitung

Extron electronics

Extron electronics Extender Wall Mount Series Bedienungsanleitung

Extron electronics

Extron electronics DTP HDMI 301 Bedienungsanleitung

Extron electronics

Extron electronics FOX USB Tx (SM) Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

Extron electronics eLink 100 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken