Extron electronics FOX 2G Tx AV Bedienungsanleitung

This guide provides instructions for an experienced installer to set up and operate the Extron®

PowerCage FOX 2G Tx/Rx AV ﬁber optic video and audio extenders.

The Extron PowerCage FOX 2G AV is a modular transmitter and

receiver pair of boards for the PowerCage 1600 enclosure, providing

long distance transmission of standard deﬁnition video, audio, and

data (RS-232) signals over a ﬁber optic cable at rates of up to 2 Gbps.

The PowerCage FOX 2G AV Tx and Rx boards are compatible

with the FOX 2G AV ﬁber optic video transmitter and receiver as

well as the FOX Series of distribution ampliﬁers, switchers, and

matrix switchers. They are not compatible with the FOXBOX 4G,

FOX 500 (RGB) and FOX 500 DVI, FOX 500 DA6, FOX 3G HD-SDI, and

PowerCage FOX 4G DVI and VGA boards.

Installation

Step 1 — Install the Boards in the Enclosure

Install the Tx, Rx, or both boards in the PowerCage 1600 enclosure

slots as required. Use a screwdriver or other tool to tighten the two

screws that hold each board in place. (See the illustration at right.)

NOTE: Ensure that the boards are ﬂush with the rear of the enclosure

and that the screws are tightened securely before applying power.

Step 2 — Connect the Input and Outputs

a. Connect a low-resolution (composite, S-video, or component) video source to one or more Video Input

connectors on the transmitter. Connect a video output device to one or more Video Output connectors on

the receiver. (The video input connectors on the transmitter are identical in appearance to the video output

connectors on the receiver; both are shown at right.)

b. Connect a balanced or unbalanced, stereo or mono audio input source to the Audio captive screw connector

on the transmitter. Connect a balanced or unbalanced stereo or mono audio output device to the Audio

captive screw connector on the receiver. (See the illustrations below.)

Unbalanced Stereo Output Balanced Stereo Output

L R

Ring

Sleeve(s)

Tip

Ring

L R

Sleeve(s)

L R

Tip

NO GROUND HERE.

Unbalanced Stereo Input Balanced Stereo Input

Ring

Sleeve (s)

Tip

Sleeve

Tip

Sleeve

Tip

Ring

Do not tin the wires!

CAUTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative

(–) contacts.

Step 3 — Connect Cables for Serial Control of an Output Device (Optional)

If you want the PowerCage FOX 2G AV units to pass serial data or control signals, such as for serial control of a

projector, connect the controlling device to the transmitter and the other device to the ﬁrst three poles of the RS-232

Over Fiber captive screw connectors on both units.

Step 4 — Connect an Alarm (Optional)

For remote monitoring of the status of the Rx optical link on either unit, connect a contact closure device to the two

Alarm poles of the Remote RS-232/Alarm 5-pole captive screw connector on the unit. When no signal light is detected,

the two poles of the connector are shorted together to activate an alert (such as sounding an alarm, turning on a room

light, or sending an e-mail).

1 2

REMOTE

RS-232

OVER FIBER

Tx Rx

ALARM

OUTPUT

RGB

PowerCage

FOX 4G RX RGB

Tx Rx

L R

AUDIO

MONO

AUDIO OUTPUT

1 2

SHARP GAIN

Y/VID C

INPUT

PowerCage

MTP R AV

Tx Rx

HD/SDI INPUT HD/SDI OUTPUTS

MODE

PowerCage

FOX 3G HD-SDI

1 2

REMOTE

RS-232

OVER FIBER

Tx Rx

ALARM

OUTPUT

RGB

PowerCage

FOX 4G RX RGB

Tx Rx

L R

AUDIO

5A MAX.

100-240V 50/60Hz

N15778

CUS

LISTED

1T23

I.T.E.

1 2

REMOTE

RS-232

OVER FIBER

Tx Rx

ALARM

VIDEO

PowerCage

FOX 2G Rx AV

Tx Rx

L R

AUDIO

Align board

and slide

into slot.

Screws

(2 per

board)

16 Available Single Board

Slots (8 double board slots)

Power

Supply

Optional

Redundant Power

Supply Slot

NOTE: Power supplies can occupy only these

two power supply slots. (Each power

supply can be mounted in either slot.)

1 2

REMOTE

RS-232

Tx Rx

ALARM

1 2

REMOTE

RS-232

OVER FIBER

Tx Rx

ALARM

VIDEO INPUT

PowerCage

FOX 2G Tx AV

Tx Rx

L R

AUDIO

RS-232

OVER FIBER

Tx Rx

PowerCage™ FOX 2G Tx/Rx AV • Setup Guide

Step 5 — Connect the Fiber Optic Cable

NOTE: See the two ﬁber cable connection drawings at right and below. You can connect the transmitter and

one or more receivers in one of the following ways:

• Unidirectional (transmitter to receiver) only: perform step a.

• Bidirectional (transmitter to receiver and return): perform steps a and b.

• Unidirectional (transmitter to receiver) with daisy-chain (receiver to receiver): perform steps

a and c.

a. Connect a ﬁber optic cable between the Tx port on the transmitter and the Rx port on the receiver.

b. If you want the receiver to send return serial data (such as responses from a controlled device) to the transmitter,

connect a ﬁber optic cable between the Tx port on the receiver and the Rx port on the transmitter.

c. If you want a receiver to daisy-chain the optical signal to another receiver (up to 10 receivers in a daisy-chain):

• Connect a ﬁber cable from the Tx port on the receiver to the Rx port on another receiver.

• Set each receiver to daisy-chain mode. See “Normal and Daisy Chain Modes,” below.

From Transmitter

or Daisy-Chained

Receiver

Tx Rx

Step 6 — Connect to the Host (Optional)

For serial control of the transmitter and receiver, connect a host device, such as a computer, to either:

• The ﬁrst three poles (Tx, Rx, and _) of the Remote RS-232/Alarm 5-pole captive screw connector on either unit.

• The Conﬁg connector on the PowerCage 1600 enclosure front panel using an optional 9-pin D to

2.5 mm mini jack TRS RS-232 cable (part number 70-335-01). Repeatedly press the front panel Comm

Select button until the Comm LED lights for the slot where the PowerCage FOX 2G transmitter or

receiver board is installed.

The protocol for these ports is:

• 9600 baud • no parity • 8 data bits • 1 stop bit • no ﬂow control

Refer to the PowerCage FOX 2G Tx/Rx AV User Guide for detailed information about using the Simple

Instruction Set (SIS™) commands and the FOX Extenders Control Program to set up and operate the

transmitter and receiver and to use the adjustments and test patterns on the PowerCage FOX 2G.

Operation

After all receivers, the transmitter, and connected devices are powered up, the system is fully operational.

If any problems occur, verify that the cables are routed and connected properly and that all display

devices have identical resolutions and refresh rates. If problems persist, call the number shown below for

the Extron S3 Sales & Technical Support Hotline at the Extron site closest to you.

Normal and Daisy Chain Modes

The receiver operates in one of two modes:

• Normal mode — The receiver outputs RS-232 and SIS commands and responses on its Tx LC connector.

• Daisy-chain mode — On its Tx connector, the receiver outputs the signal stream that it receives on its Rx connector. Up to 10

receivers, each in daisy chain mode, can be connected to a single transmitter.

Use SIS commands issued to the connected unit to toggle between normal and daisy-chain modes. Connect a computer to the

Remote RS-232 port of either unit or to the Conﬁg port on the PowerCage enclosure and issue the 66*0*n# command. For n:

2 = Enable daisy chain mode; 0 or 1 = disable daisy chain mode.

You can also switch operating modes using the FOX Extenders Control Program (refer to the program help ﬁle for details).

COMM

POWER

ALARM

COMM

SELECT

CONFIG

Comm

Select

Button

Config

Port

Comm

LED

68-1914-50

Rev A

09 10

RxTx

and

Extron USA - West

Headquarters

+800.633.9876

Inside USA/Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA/Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

1 2

REMOTE

RS-232

Tx Rx

ALARM

PowerCage™ FOX 2G Tx/Rx AV • Setup Guide (Continued)

Andere Handbücher für FOX 2G Tx AV

Dieses Handbuch passt für folgende Modelle

Andere Extron electronics Empfänger Handbücher

Extron electronics

Extron electronics Twisted Pair Transmitter TP T 15HD A Bedienungsanleitung

Extron electronics

Extron electronics DVI 104 Tx/Rx Bedienungsanleitung

Extron electronics

Extron electronics FOX3 SR 301 Bedienungsanleitung

Extron electronics

Extron electronics Fiber Optic Transmitter-Receiver Pair FOX 500 DVI... Bedienungsanleitung

Extron electronics

Extron electronics FOX 2G Tx AV Bedienungsanleitung

Extron electronics

Extron electronics FOX 500 Tx Bedienungsanleitung

Extron electronics

Extron electronics MTP 1500RL 15HD A SEQ Bedienungsanleitung

Extron electronics

Extron electronics DFX 100 Tx Bedienungsanleitung

Extron electronics

Extron electronics Dual Link DVI Transmitter and Receiver DVI DL 201... Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX SR HDMI Bedienungsanleitung

Extron electronics

Extron electronics FOX3 T 301 Bedienungsanleitung

Extron electronics

Extron electronics MTP C7 T 15HD RS Bedienungsanleitung

Extron electronics

Extron electronics HFX 100 Tx Bedienungsanleitung

Extron electronics

Extron electronics TP R BNC A Bedienungsanleitung

Extron electronics

Extron electronics VersaTools MTP T SV Bedienungsanleitung

Extron electronics

Extron electronics Digital Video Transmitter and Receiver HDMI 201... Bedienungsanleitung

Extron electronics

Extron electronics MTP/HDMI U R Bedienungsanleitung

Extron electronics

Extron electronics MTP/HDMI U R Bedienungsanleitung

Extron electronics

Extron electronics Dual Link DVI Transmitter and Receiver DVI DL 201... Bedienungsanleitung

Extron electronics

Extron electronics XTP R HDMI Bedienungsanleitung

Extron electronics

Extron electronics XTP T HDMI Bedienungsanleitung

Extron electronics

Extron electronics Twisted Pair Transmitter VTT001 Bedienungsanleitung

Extron electronics

Extron electronics XTP SFR HD 4K Bedienungsanleitung

Extron electronics

Extron electronics Dual Link DVI Transmitter and Receiver DVI DL 201... Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung