Extron electronics TLP 1000MV Bedienungsanleitung

Product Category

IMPORTANT:

Refer to www.extron.com for

the complete TLP 1000 Series

user guide before connecting

the product to the power source.

TLP 1000MV and TLP 1000TV • Setup Guide

Overview

The Extron TLP 1000MV (wall-mounted) and TLP 1000TV (desk-mounted) TouchLink™Panels provide simple and versatile

conﬁguration and control for a range of IP Link®control systems. Graphic and text objects are displayed on the screen.

These objects have system control functions associated with them and the touch overlay allows you to activate or regulate

those functions.

These touchpanels communicate through an Ethernet connection to a conﬁgurable IP Link control processor. Video and

audio input is provided by a twisted pair cable connected to an MTP transmitter.

NOTE: The network output must be connected to a network switch, hub, or router that is connected to an Ethernet

LAN or the Internet. An Extron IP Link controller must also be connected to the same network. Suggested

models include IPL T S series (for example, IPL T S4), IPL 250, IPL T CR48, IPL T SFI244, or IPCP 505.

Extron strongly recommends that power is provided by a Power over Ethernet (PoE) power supply.

This guide provides basic instructions for experienced installers to mount and perform initial conﬁguration on the

TLP 1000 series of touchpanels. Full instructions and reference material can be found in the TLP 1000MV and TLP 1000TV

User Guide, which is available on the Extron website (www.extron.com).

Front Panel Features

Extron TLP 1000MV Extron TLP 1000TV

aMotion Sensor — when no motion has been detected for a user-deﬁned period of time, the unit goes into sleep

mode. When motion is detected by the sensor, the screen display is restored and active.

bMicrophone — is located below the LCD screen.

cConnection status LED — is unlit during normal operation. The LED blinks red if the connection to the IP Link

controller is lost.

dProgrammable LEDs — one on each top corner can be programmed to provide system feedback. They light red or

green and can blink or light solid.

eLCD screen — has a 1024x600 resolution with a touch overlay. Extron software is used to design and conﬁgure a

graphic user interface to display buttons, text, or icons, which have user-deﬁned functions associated with them.

fSpeakers — Two speakers placed under the screen, on either side of the panel, provide audible feedback for the user.

gLight Sensor — (can only be seen from above the unit) monitors ambient light level and adjusts screen brightness.

Product Category

810

Extron TLP 1000MV

Use the Extron pry tool to remove the front faceplate of the

TLP 1000MV:

hMenu button — activates the on-screen menus for calibrating

the unit (see page 3).

iReset button — allows the unit to be reset in any of four

different modes (see “Reset Modes” on page 4).

jReset LED — provides feedback about the reset status when the

user presses the reset button (see “Reset Modes” on page 4).

TLP 1000MV Reset Buttons and LED

Rear Panel Features

Extron TLP 1000MV Extron TLP 1000TV

h (Menu button), i (Reset button), and j (Reset LED) — see “TLP 1000MV Reset Buttons and LED“ above.

kMTP Signal Adjustments — Three MTP signal adjustments are available for S-video luminance gain (VID/Y), S-video

chrominance gain (C), and sharpness (S). For composite video signals, the gain is controlled by the VID/Y adjustment.

lMTP Input (optional) — A twisted pair cable, terminated with an RJ-45 connector, provides video and audio input

from an Extron MTP transmitter. For the TLP 1000TV, the MTP port is in the top surface of the recessed area, indicated

by the red arrow.

CAUTION: Ensure the MTP cable is connected to the MTP input and the network cable is connected to the

Network input. The voltages carried by the cables is different and connecting the MTP cable to the

Network input will damage the touchpanel unit.

mNetwork and Power over Ethernet Connector — A twisted pair cable, terminated

with an RJ-45 connector, provides network connection. For the TLP 1000TV, the LAN

port is in the top surface of the recessed area, indicated by the blue arrow.

Extron recommends using the Power over Ethernet (PoE) power supply (provided).

Use straight-through cables to connect the LAN-IN port to a network switch and the

PWR LAN-OUT port to the LAN port of the touchpanel (see the ﬁgure to the right).

Connect the IEC power cord to a convenient 100 VAC to 240 VAC, 50-60 Hz power

source.

An Extron IP Link control interface must also be connected to the same network

domain as the TouchLink Panel. See the note on page 1 for a list of suggested models.

CAUTION: Do not connect any power supply before reading the Cautions about power supplies in the “Panel

Features” section of the TLP 1000MV and TLP 1000TV User Guide.

nPower connector (optional) — Extron recommends using the PoE power supply (provided). As an alternative,

you may choose to connect the two pole, 3.5 mm captive screw connector from the 12 VDC, 1.0 A power supply (not

provided) to the power supply socket on the rear panel.

oVESA mounting holes (TLP 1000TV only) — For use with the Extron LPVM-1 (part number 60-1099-02). For

complete mounting options of both the TLP 1000MV and TLP 1000TV, see the TLP 1000MV and TLP 1000TV User Guide.

PWR LAN-OUT LAN-IN

To Networ

k Switch

To TLP 1000

Power over Ethernet (PoE) Power Supply

Product Category

Initial Conguration

Before use, conﬁgure the touchpanel, using the on-screen menus.

1. Press the Menu button once. (See “TLP 1000MV Reset Buttons and LED“

for the TLP 1000MV or “Rear Panel Features“ for the TLP 1000TV.) The

Main menu screen opens (see ﬁgure at right).

2. Touch an on-screen button to highlight and select that option (the button

turns green with a yellow border).

3. Use the Up and Down buttons to adjust the value. Some options have a

single button and toggle between Off and On when the button is pressed.

There are ﬁve different screens (Main, Volume, Time, Network, and Video) that

can be selected by pressing the appropriate button at the left side of the screen. There is also an Exit button at the bottom

left corner of the screen for leaving the menus.

Use the screens to adjust the following options (for more information, see the TLP 1000MV and TLP 1000TV User Guide).

Main — Adjusts the Sleep timer, Backlight, Auto Backlight, and Wake on Motion functions. The screen also provides

information about the PoE status.

Volume — Adjusts the Master, Click, Sounds, and Line In volume settings.

Time — Sets the correct time and date.

Network — Sets the IP address and the subnet mask, and enables or disables Dynamic Host Conﬁguration Protocol.

Video — Provides a small video preview window and the controls to adjust the video contrast, color, brightness, and tint.

Calibration Menu

1. Press the Menu button a second time to open the calibration-screen. (See

“TLP 1000MV Reset Buttons and LED“ for the TLP 1000MV or “Rear Panel

Features“ for the TLP 1000TV.) The on-screen button in the top left corner

is highlighted.

2. Press the highlighted button until it turns gray and a new button is

highlighted. When all four points have been calibrated, the screen reopens

to the Main Screen.

3. Press Exit to close the on-screen menus.

4. If necessary (for the TLP 1000MV), reattach the faceplate.

Mounting Options

TLP 1000MV

zWall-mounting — using the Extron BB 1000M back box (part number 70-887-01) or the Extron EWB 1000 wall box

(part number 70-950-02), either of which must be purchased separately. Follow the instructions provided with the kit.

The unit may also be mounted directly to the wall without a kit, as described on page 4.

zFurniture-mounting — as described on page 4.

zRack-mounting — using the RM 1000M kit (part number 70-886-01), which must be purchased separately. Follow the

instructions in the user guide provided with the kit.

TLP 1000TV

zDesktop-mounting — by standing the unit on a suitable surface. For added security, the unit may be attached to the

desktop, using two screws, as described in the TLP 1000MV and TLP 1000TV User Guide.

The TLP 1000TV can also be mounted using the Extron SMA-1 Swivel-Mount Adapter (part number 70-747-01), which

must be purchased separately. Follow the instructions provided with the kit and the TLP 1000MV and TLP 1000TV User

Guide.

zVESA-mounting — using the D-type (75 x 75 mm) mounting pattern. The Extron LPVM-1 kit (part number 60-1099-02)

is optional and must be purchased separately. Follow the instructions provided with the kit. To VESA-mount the TLP

1000TV, the base must be removed from the unit, as described in the TLP 1000MV and TLP 1000TV User Guide.

Main

Volume

Time

Network

Video

Exit

Down Up

Sleep timer: 300 Sec

Down Up

Backlight: 073%

Auto Backlight

Wake on Motion

PoE

Active

Press and Hold

Highlighted Box

Until Color Changes

68-1909-50 Rev. A

03 11

Extron USA - West

Headquarters

+800.633.9876

Inside USA/Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA/Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

TLP 1000MV and TLP 1000TV • Setup Guide (Cont’d)

Wall-Mounting or Furniture-Mounting the TLP 1000MV

To mount the TLP 1000MV directly into a wall, follow these steps. The steps will be similar if the unit is mounted in furniture

(such as a podium or table).

1. Use the template provided to mark the wall at a

suitable location and cut a hole 10.06 inches (25.55 cm)

wide x 6.98 inches (17.73 cm) high.

2. Unpack the TLP 1000MV and remove the faceplate.

3. Ensure all the locking arms are ﬂush with the unit and

that the TLP 1000MV can ﬁt into the hole. If necessary,

use a rasp or a coarse ﬁle to enlarge the hole.

4. Run the network and MTP cable connections inside the

wall to the hole, leaving enough slack in the cables to

connect them to the back of the TLP 1000MV.

5. Plug the cables into the rear panel connectors (see

page 2).

zConnect the LAN port to the PoE power supply and

network.

zConnect the RJ-45 MTP input.

zOptional: Extron recommends using the Power over Ethernet power supply provided. However, you may use the

LAN port only as a network connection and connect a 12 VDC, 1.0 A power supply (not provided) to the 2-pole

captive screw power input.

6. Push excess cables into the wall cavity.

7. Ensure the ﬁve locking arms (three at the top and two at the bottom) are ﬂush with top and bottom of the

TLP 1000MV and ﬁt the touchpanel into the hole.

8. Use a Phillips head screwdriver to tighten the screws for the locking arms. As the screws tighten, the locking arms rotate

behind the wall and hold the unit in place. Do not overtighten the screws as this can damage the catches or the wall.

9. If required, perform the initial calibration (see page 3).

10. Replace the faceplate by pressing the catches on the faceplate into the corresponding holes on the front of the panel.

Reset Modes

The touchpanels have four reset modes: Factory Firmware Mode, Run or Stop Events Mode, Reset All IP Settings Mode, and

Reset Factory Defaults Mode. These modes can be initiated by pressing the reset button (see “TLP 1000MV Reset Buttons

and LED“ for the TLP 1000MV or “Rear Panel Features“ for the TLP 1000TV). For full information about these different

modes, see the TLP 1000MV and TLP 1000TV User Guide.

Screen Design and Conguration

Use Extron GUI Conﬁgurator (version 1.2 or later) to design the graphical user interface that will appear on the TouchLink

panel. Use Extron Global Conﬁgurator (version 3.1 or later) to assign functions to the elements of the graphical user

interface. For complete information about these software programs, see the help ﬁle of the appropriate program.

Faceplate Snaps to Unit

(4 plcs ea side)

Tighten Screws to

Rotate Locking Arms

Andere Handbücher für TLP 1000MV

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extron electronics Touchscreen Handbücher

Extron electronics

Extron electronics TouchLink TLP Pro 520M Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1220MG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1230WTG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1725TG Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP 710CV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1220TG Bedienungsanleitung

Extron electronics

Extron electronics RWM 1 Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1230WTG Bedienungsanleitung

Extron electronics

Extron electronics TLP 700TV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1220TG Bedienungsanleitung

Extron electronics

Extron electronics Scan Rate Indicator SRI 200 Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1520TG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP 710TV Bedienungsanleitung

Extron electronics

Extron electronics TLP 710MV Bedienungsanleitung

Extron electronics

Extron electronics TLP 1000MV Bedienungsanleitung

Extron electronics

Extron electronics TLP 1000MV Bedienungsanleitung

Extron electronics

Extron electronics TLP 350MV Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP Pro 1025T Series Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP 350CV Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP 710CV Bedienungsanleitung

Extron electronics

Extron electronics ZRTP Series Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225TG Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung