Extron electronics TLP Pro 720C Bedienungsanleitung

IMPORTANT:

Go to www.extron.com for the

complete user guide and installation

instructions before connecting the

product to the power source.

TLP Pro 720C • Setup Guide

Overview

The Extron TLP Pro 720C is a 7 inch Cable Cubby touchpanel with a ip-up, 800x480 LCD touchscreen with 18-bit color depth.

It is ideal for any AV application requiring a full-size, Cable Cubby touchpanel with a customizable interface. This guide provides

instructions for experienced installers to mount and install a TLPPro 720C touchpanel. For more complete instructions, see the

TLPPro 720C User Guide, at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software (available from www.extron.com):

GUI Designer — For designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces.

Global Configurator®Professional or Global Configurator Plus — For setting up and conguring the control

processor and touchpanel.

Toolbelt — Provides device discovery, device information, rmware updates, and conguration of network settings,

system utilities, and user management for TouchLink Pro devices.

Global Scripter®— Provides an integrated development environment for Extron control systems programming.

NOTE: All four software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you will also require

IP address Subnet mask Gateway

Username — This can be either admin or user.

Passwords — The factory congured passwords for all accounts on this device have been set to the device serial

number. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the password will be the default password conguration. The default

password is extron (for either admin or user).

Make a note of the touchpanel MAC address.

Make sure you are familiar with all the included parts and have all the Tools Required for Installation (see page 2).

Included Parts

TLP Pro 720C

Table Clamps

AC Power Module*

Blank AAPs

Pass-thru AAPs

Extron

Removal Tool

Zip Ties #4−40 Screws

and Nuts

2 Pos

AAP Shelf Bracket Kits

(2 brackets/kit)

3 Pos1 Pos

NOTES:

*Inside the US, the TLP Pro 720C can be purchased with or without an AC

power module. Outside the US, see www.extron.com to nd an AC power

module for your country.

†Active or Passive AAPs must be purchased separately (see www.extron.

com).

Figure 1. Included Parts

With Power

Module

Without Power

Module

AC Power Module* 1 0

Pass-through AAPs†3 3

Blank AAPs 6 6

1-position bracket kit 0 1

2-position bracket kit 3 4

3-position bracket kit 1 1

TLP Pro 720C • Setup Guide (Continued)

Tools Required for Installation

Safety Glasses

Phillips Screw Driver

Tape Measure

1/4" Hex Nut Driver

Marking Pen

Square

Vacuum Cleaner

Figure 2. Tools Required for Installation

Mount and Cable All Devices

ATTENTION:

• Do not power on the touchpanels until you have read the Attention in the Power Supply section of the TLP Pro 720C

User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «sources d’alimentation» du

TLP Pro 720C UserGuide.

Mount the units (see Mounting below).

Install power modules in the cable cubby.

Install AAPs and run cables to the cable cubby.

Connect cables to the touchpanels.

Connect the power cords and power on all devices.

Set up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor, and the touchpanel to the same Ethernet subnetwork.

Use the Setup Menu (see page 8) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask,

gateway, and related settings for the touchpanel.

Conﬁgure the Touchpanels

The GUI Designer Help File, the Global Conﬁgurator Help File, and the Toolbelt Help File provide step-by-step instructions and

detailed information. The Global Conﬁgurator Help File includes an introduction to the software and sections on how to start a

project and conguration.

Global Scripter provides an Extron-exclusive Python library (ControlScript®) and Global Scripter modules to get you started.

Mounting

Planning

Before making any cuts, select the best location for the TLPPro 720C.

Ensure that the edge that opens on the lid is oriented correctly.

Ensure there is enough space for all the system cables and components, including cable retractors, if they are to be installed.

The space requirements for retractors are shown in the TLP Pro 720C User Guide, which is available at www.extron.com.

Decide on the method for cutting a hole in the table:

Hand router and metal router guide

CNC wood router

Jigsaw and paper template

Verify that you have the correct template or dimensions.

Check all relevant regulations.

Ensure that the installation complies with local, state, and national building and electrical codes.

Ensure that the installation complies with the Americans with Disabilities Act or other accessibility requirements.

Product Category

Step 1 — Obtain Cut-out Dimensions

ATTENTION:

• The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople. Exercise care

to prevent scarring or damaging the furniture.

• L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et qualiés.

Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.

• Use the appropriate metal Extron routing template or refer to the surface cutout dimensions before cutting a hole in

the furniture or other surface. Pay special attention to the direction the unit will face. The connector access side is

underlined (see Using a CNC wood cutter below). Extron is not responsible for miscut mounting holes.

• Utilisez le gabarit de détourage métallique approprié ou reportez-vous aux dimensions de découpe de la surface

indiquées ci-après avant de découper le meuble ou la surface. Faites particulièrement attention à la directions dans

laquelle l’unité sera dirigée. Le côté pour accéder au connecteurs est souligné (voir Using a CNC wood cutter

ci-dessous). Extron ne sera pas responsable des erreurs de coupe.

• Ensure that the orientation of the Cable Cubby and the hole dimensions are correct before cutting the table.

• Assurez vous que la position du CableCubby et les dimensions du trou soient correctes avant de couper la table.

• Ensure the table surface is at least 0.375 inch (0.95 cm) thick.

• Assurez vous que la surface de la table est au moins 0,95 cm (0,375 pouce) d’épaisseur.

If using a hand router, you should purchase the Extron TLP Pro 720C routing template (see “Installation Routing Templates for

Cable Cubby Series/2 Enclosures” at www.extron.com).

If using a CNC wood router, use the exact cut-out dimensions (see Using a CNC wood cutter below).

If using a reciprocating saw or jigsaw, use the paper cut-out template (available under the Downloads tab on the TLP Pro 720C

page at www.extron.com).

Step 2 — Cut the Surface

CAUTION: Risk of personal injury: Wear safety glasses when operating power equipment.

ATTENTION : Risque de blessure: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique.

Be certain the cut is laid out in exactly the desired location and the edge that opens on the lid is correctly oriented. After verifying

and checking dimensions, cut a hole in the surface of the furniture where the enclosure will be installed (see “Preparing the Table”

in the TLP Pro 720C User Guide). There are three methods for cutting the hole in the table:

Using a hand router

Recommended method — Use the Extron TLP Pro 720C routing

template. Refer to the Routing Template User Guide, available at

www.extron.com, to prepare the template and use the template to

cut the hole.

NOTE: The metal router guide must be purchased separately. It is

reusable and should not be discarded when the installation is

complete.

Using a CNC wood cutter

Recommended method — Use the exact cut-out dimensions:

8.90 +0.00/-0.02 inches W x 7.10 +0.00/-0.02 inches D

(22.61 +0.00/-0.05 cm W x 18.03 +0.00/-0.05 cm D)

NOTE: The underlined dimension is the connector or AAP access

side for the unit.

Using a reciprocating saw or jigsaw

Acceptable method — Use the paper cut-out template

(available under the Downloads tab on the TLPPro 720C page at

www.extron.com).

HSA 200

USER ACCESS

HSA 200

CABLE CUBBY 300

USER ACCESS

Figure 3. Using a Hand Router

Cut-Out Template for the Extron

TLP Pro 720C

Outer Edge of Trim Ring

(Do not cut this line.)

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray) from the template.

3. Mark the position on the wall or

furniture where the TLP 710MV

is being installed.

4. Cut the opening.

P/N 68-2046-01 Rev. B

Page size: 11" x 17"

Print scale 1:1

Do not shrink.

P/N

Figure 4. Using a Reciprocating Saw or Jigsaw

Step 2

TLP Pro 720C • Setup Guide (Continued)

Step 3 — Run all Cables

Run all cables necessary to support the AC connector, the cables stored in the cubby, and all planned AAP connectors. Run the

cables below the table and through the hole that was cut in Step 2. Leave enough slack in the cables to connect or route them

before the cubby is installed in the table. Leave enough space under the TLPPro 720C enclosure for the external power supply

and connection of AV cables and the network connection.

Step 4 — Install Cable Retractors (Optional)

If required, Extron cable retractors must be purchased separately. It is difcult to mount the Cable Cubby into the table after the

retractors have already been installed, so Extron recommends installing the empty retractor bracket at this point. The bracket

should be secured using the lowest level of mounting holes inside the touchpanel enclosure.

The retractors should be added to the bracket after Step 8 — Mounting the Enclosure on page 6. For complete information

about retractors and how to install them, see the TLP Pro 720C User Guide and Retractors User Guide at www.extron.com.

Step 5 — Install Power Module (Optional)

ATTENTION:

• For units that are used in North America, only

use AC power modules that are UL Listed Model

“Cable Cubby AC Power Module”.

• Pour les unités qui sont utilisées en Amérique

du Nord, utilisez seulement les modules

d’alimentation secteur qui sont listés UL, modèle

« Cable Cubby AC Power Module ».

• The unit is not UL Listed if it uses any AC power

module other than Model “Cable Cubby AC Power

Module”.

• L’unité n’est pas listée UL si elle utilise tout autre

module d’alimentation secteur autre que le modèle

« Cable Cubby AC Power Module ».

Secur

e the power module

o the TLP Pro 720C frame

with #4-40 Phillips head

rews and star washers.

Extron

Figure 5. Securing the Power Module

NOTE: For models that do not include a power module, see the Extron website to select a power module that is suitable for

your location.

The power module takes up two or three AAP spaces, depending on the model, and may be installed before or after the AAP

assembly is installed. It may be installed with AAPs on either side.

1. Secure the power module into position with #4-40 Phillips head screws and star washers.

CAUTION: Risk of electric shock: To ensure proper electrical grounding, use the provided grounding screws and star

washers.

ATTENTION : Risque de choc électrique: An d’assurer une mise à la terre correcte, utilisez les xations de mise à la

terre et les rondelles en étoile fournies.

2. Run the cable or conduit to a convenient junction box. Extron recommends the circuit be attached to a junction box that is

directly wired to the main circuit.

Product Category

Step 6 — AAP Assembly

Install all desired cables into the cable pass-through AAPs and

install the AAPs into the cable cubby.

The simplest way to install the cables and AAPs is to populate

the AAP brackets outside the cubby and then install the

populated AAP shelf assembly into the cubby.

Install cables in the pass-through holes as shown in the gure to

the right.

TIP: Hand tightening the #4-40 nuts makes it easier to

place and secure the assembly inside the enclosure.

NOTE: An extra column of AAP bracket mounting points is

available for use with TLP Single-space AAP mounting

brackets. Single-space brackets will not t in any other

location.

Rear Bracke

Front Brackets

The extra column

of mounting points

is for installing

single-space

AAP brackets.

Figure 6. AAP Assembly

Step 7 — Install the AAP Assembly

1. From under the table, push the rst AAP assembly

through the bottom of the enclosure. The holes in the rear

bracket must align with the bottom row of holes on the

rear face of the enclosure.

TIP: Ensure there is enough space above the AAP

assembly for the lid to close completely without

cables or connectors contacting the touchpanel.

2. Secure the AAP assembly into position with the provided

Phillips head screws.

3. Tighten the nuts that secure the AAPs to the brackets.

COMPUTER

AUDIO

Phillips Head Scr

ews

(secur

e AAP

assemb

ly)

Tighten down

AAP nuts.

Push assembly thr

ough

bottom of enclosure.

Large slot

provides tool

access to fasten

rear brackets.

Extron

Figure 7. Installing the AAP Assembly

TLP Pro 720C • Setup Guide (Continued)

Step 8 — Mounting the Enclosure

CAUTION: The anged edges of the top of the surface enclosure are sharp. These edges are also soft and may be easily

nicked or bent. Exercise caution when handling the enclosure to prevent personal injury or damage to the enclosure.

ATTENTION : Les extrémités à brides du haut de la surface du boîtier sont aiguisées. Ces extrémités sont aussi lisses

et peuvent facilement être coupées ou pliées. Soyez prudents lorsque vous manipulez le boîtier an d’éviter de

l’endommager ou de vous blesser.

1. Remove the edge grommet protecting the edges of the trim ring

and the plastic lm on the nished surfaces.

ATTENTION:

• Do not use isopropyl alcohol or other solvents to

clean the Cable Cubby. Strong solvents will ruin some

nishes.

• Ne pas utiliser de l’alcool isoproprylique ou d’autres

solvants pour nettoyer le CableCubby. Les solvants

forts endommageront certaines nitions.

2. Carefully lower the enclosure into the hole cut in the table

(see Step 2 — Cut the Surface on page 3). Ensure the

trimring(5) is ush with the top of the table.

3. Under the table, attach the table clamps (3) to the pins on each

side of the enclosure. It may be necessary to loosen the wingnuts

(1) and the Phillips head screws (2).

Figure 8. Mount the Enclosure

4. When the clamps are properly seated on the pins, tighten the Phillips head screws until the clamp faces (4) are tightly

secured against the bottom of the table. To prevent the screws from becoming loose, secure the wingnuts against the table

clamp bodies.

Connecting the TLP Pro 720C

The cable connections are located in a panel on the bottom of the TLP Pro 720C:

Figure 9. TLP Pro 720C Cable Connectors

APower connector — Connect a 12 VDC, 1.0 A power supply (not provided) to this 2-pole, 3.5 mm captive screw connector.

ATTENTION:

• The TLP Pro 720C can use a 12 VDC desktop power supply and is also Power over Ethernet (PoE 802.3af,

class3) compliant. Do not connect either power supply before reading the Attention in the Power Supply sections

of the TLPPro720C User Guide.

• Le TLP Pro 720C peut utiliser une source d’alimentation externe 12 Vcc, et est également compatible avec

l’alimentation POE via Ethernet (PoE 802.3af, classe 3). Ne branchez pas de sources d’alimentation externes

avant d’avoir lu les mises en garde dans la section «PowerSupply» du TLPPro720C User Guide.

NOTES:

• The TLP Pro 720C ships without a power supply. Either the 12 VDC power supply or the power injector must be

purchased separately.

• If a 12 VDC power supply and a power injector are both connected to the TLP Pro 720C, the power injector takes

precedence. If a PoE power loss is detected, the touchpanel switches seamlessly to the 12 VDC power supply

without needing a system reboot.

BNetwork and Power over Ethernet (PoE) Connector — Connect the touchpanel to the LAN using a twisted pair cable,

terminated with an RJ-45 connector. The connector can also be used with a PoE power injector (not provided).

An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.

Product Category

Front Panel Features

To see all the front panel features, remove the bezel, using the Extron Removal Tool (see Included Parts on page 1). For a

complete description of all these features and their function, see the TLP Pro 720C User Guide.

ATTENTION:

• When you slide the removal tool between the screen and the bezel, take care to avoid damaging the ribbon

cable, which runs close to the edge of the bezel.

• Lorsque vous faites glisser l’outil d’extraction entre l’écran et le châssis, faites attention à éviter d’endommager

la nappe de raccordement se trouvant à proximité du bord du châssis.

AAmbient light sensor — This sensor monitors ambient light level and adjusts screen brightness, based on the settings

congured using the Setup Menu (see page 8).

BBezel attachment point — The TLP Pro 720C has eight attachment points (two on each side, two on the top edge, and two

on the bottom edge).

CLCD screen — The TLP Pro 720C has a 7 inch screen with a 800x480 resolution.

DReset LED— This LED indicates power status and reset status of the device.

ECommunication LED — This LED shows the conguration and connection status of the touchpanel:

zUnlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).

zBlinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.

zPermanently lit if the touchpanel has not been congured and is not connected to an IP Link Pro control processor.

The indicator can be toggled between enabled and disabled, using the Setup Menu (see page 8).

FReset button — This button allows the unit to be reset. The TLP Pro 720C has three reset modes that are initiated by

pressing the reset button (see Reset Modes: a Brief Summary on page 8). For full information about these different

modes, see the TLPPro 720C User Guide.

GMenu button — This button activates the Setup Menu and Calibration Screen (see page 8).

HBezel — To detach the bezel, use the included removal tool (see the gure to the right, above).

ISpeaker — A single speaker, located inside the cable cubby, provides audible feedback for the user.

JBezel removal slots — The slots allow for the removal of the bezel, using an Extron removal tool.

KIllumination LED — This LED provides light for cable cubby enclosure.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

For information about replacing and disposing of batteries, see the TLP Pro 720C User Guide at www.extron.com.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876 68-2406-50 D

01 21

TLP Pro 720C • Setup Guide (Continued)

Reset Modes: a Brief Summary

The TLP Pro 720C offers the following reset modes (see the TLP Pro 720C User Guide for complete information):

• Use factory firmware: Press and hold the Reset button (see Front Panel Features, F, on page 7) while

applying power to the unit. Use this mode to replace rmware in the event of rmware

failure.

• Reset All IP Settings: Press and hold the Reset button for 6 seconds. After the Reset LED (D) ashes twice,

release and momentarily press the Reset button. Use this mode to reset all network

settings without affecting user-loaded les.

• Reset to Factory Defaults: Press and hold the Reset button for 9 seconds. After the Reset LED ashes three times,

release and momentarily press the Reset button. Use this mode to return the interface to

factory default settings.

NOTES:

• The factory congured passwords for all accounts on this device have been set

to the device serial number. Passwords can be changed during conguration.

Passwords are case sensitive.

• If the device is reset to default settings, the passwords are reset to the default

password, which is extron (for either admin or user).

• Enable or Disable the DHCP

Client

Use this mode to toggle between DHCP enabled and DHCP disabled. Press the Reset

button ve times consecutively. After the fth press, do not press the button again within 3

seconds. If DHCP was enabled, it is now disabled and the Reset LED blinks three times. If

DHCP was disabled, it is now enabled and the Reset LED blinks six times.

Setup Menu

The setup menu opens when the menu button is pressed (G). There are

ve different screens: Status, (shown in the gure to the right) Network,

Display, Audio, and Advanced. The screens can be selected by pressing

the appropriate button in the navigation bar at the top of the screen (for

more information, see the TLPPro 720C User Guide).

Press the menu button for at least 2 seconds to open the calibration

screen. Follow the on-screen instructions.

Status DisplayAudioAdvanced Exit

Network

Info

Model: TLP Pro 720C

Part Number: 60-1396-020A

Firmware

Version: 1.00

PoE Status:On

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:

Project:

Sleep Timer:

800x480

N/A

5 Minutes

Audio

Master Volume:

Master Mute:Off

Advanced

Controller IP:N/A

Project Size:N/A

Calibration Screen

Andere Handbücher für TLP Pro 720C

Inhaltsverzeichnis

Andere Extron electronics Touchscreen Handbücher

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TLP 1000MV Bedienungsanleitung

Extron electronics

Extron electronics TLP 1000MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225MG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TLP 710MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225TG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 725T Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP Pro 1220 Series Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 525M seriesl Bedienungsanleitung

Extron electronics

Extron electronics SMK 2 Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TLP 710MV Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP Pro 1020 Series Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 725T Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 300M Series Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1020T Bedienungsanleitung

Extron electronics

Extron electronics TLP 350MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1725TG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225MG Bedienungsanleitung

Extron electronics

Extron electronics TLP 1000MV Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1230WTG Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung