Extron electronics DTP T FB 232 Bedienungsanleitung

DTP T FB 332 and DTP T FB 232 • Setup Guide

This guide provides instructions for an experienced installer to install either

the Extron DTP T FB 332 or the DTP T FB 232 switching transmitter into an

Ackermann GB3 (OBO Betterman), MK Electric CableLink Plus Modular,

MK Electric CableLink Plus

Single Pan, ElectraPlan, or PUK

oor box and to make all

connections.

The transmitters switch

between one analog video and

one digital (HDMI) video input

and, paired with a compatible

receiver, can extend the

selected signal up to

330 feet (100 m) (DTP T FB 332) or

230 feet (70 m) (DTP T FB 232).

Installation

Planning

CAUTION: Failure to check these items may result in personal injury or property damage.

ATTENTION : La non-vérication des éléments listés ci-dessous peut provoquer des blessures ou dommages matériels.

Check that the installation meets the building, electrical, and safety codes.

Mounting and Cabling

Typical Floor box

Step 1 —Preparing the ﬂoor box

a. Install the oor box as directed by the manufacturer.

NOTE: Run all required cables and secure them with cable clamps.

b. Turn off or disconnect all equipment power sources.

Step 2 —Installing adapters

a. Determine a position in the oor box to mount the DTP T FB unit (see the image at right).

b. Identify the applicable adapter plates for the oor box (see the table below).

c. Install adapter plates to the same pair of mounting slots (see the table below for slot

recommendations) for the same position in the oor box. Slide the top ange into the

mounting slot and rotate the adapter plate down so the bottom ange rests against the

wall of the oor box.

Floor Box Adapter Plates Positions Highest

Mounting Slot

Additional Notes

Ackermann GB3

(OBO Betterman)

995241 (2)

995241 (2) and 995242 (1)

1 and 3

3rd from top For position 2, use the provided screws to attach

the 995242 adapter plate to either 995241

adapter plate.

MK Electric CableLink Plus

Single Pan

995243 (2) 1 and 3 N/ADo not use position 2. Use mounting screws to

secure the adapter plates to the oor box (see

ﬁgure 3 on page 3).

MK Electric CableLink Plus Modular 995244 (2) 1, 2, and 3 3rd from top

ElectraPlan 995300 (2) 1, 2, and 3 3rd from top

PUK 995300 (2) 1, 2, and 3 3rd from top

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications bef

ore connecting the

oduct to the po

wer source.

CONFIG G

RS-232 IR

Rx Tx

Tx Rx

HDMI IN VGA IN

DTP T FB 332

AUDIO IN

OVER DTP

RESET

HDMI

VGA

HDCP

AUTO

Top Panel

Figure 1. DTP T FB Unit features

Side (under adapter plate)

(Before installation in ﬂoor box)

Side (above adapter plate)

(After installation in ﬂoor box)

Top

ADC power input

BRemote RS-232

CTP function switch

DDTP output

EHDMI input

FVGA Input

GAudio input

HRS-232/IR Over TP output

IConguration (USB)

JReset button

KLEDs

SIG LINK

OUT

REMOTE

RS-232

Rx Tx

POWER

12V

1.0A MAX

−+

DTP

HDBT

Side Panel

DTP T FB 332 and DTP T FB 232 • Setup Guide (Continued)

Step 3 — Make side panel connections under the adapter plates and set the

TP function switch

APower (see ﬁgure 1 on page 1) — Connect the included 12 VDC power supply to either unit,

transmitter or receiver, as shown at right. Use the included tie-wrap to strap the cord to the

captive screw connector.

Connect an IEC power cord between the power supply and a 100-240 VAC, 50-60 Hz source.

NOTE: If the TP switch (C) is in DTP, one power supply can power both units.

If the switch is in HDBT, each unit requires its own power supply.

BRemote RS-232 port — For serial RS-232 control, connect a host device or control system to

the 3.5 mm, 3-pole captive screw connector. The wiring and protocol are shown at right.

CTP function switch —

If the receiving device is in the Extron DTP series, set this switch to DTP. The TP output

consists of HDMI with embedded audio, analog audio, RS-232 and IR, and remote power. The

transmitter and receiver can be powered by one 12 VDC power supply connected to either unit.

For an HDBaseT-enabled receiver type, set this switch to HDBT position. The TP output consists of HDMI with embedded audio plus

RS-232 and IR. The transmitter and receiver each requires its own 12 VDC power supply.

ATTENTION:

• Position this switch BEFORE connecting the appropriate device to the TP connector. Failure to comply can damage the

endpoint.

• Positionnez le sélecteur AVANT de connecter l’appareil approprié au connecteur TP. Ne pas respecter cette procédure

pourrait endommager le point de connexion.

DOut port— Connect the Out (RJ-45) port to the DTP In port on the receiver. Extron recommends that you terminate both cable ends in

accordance with the following, at a minimum: TIA/EIA T 568B and 24 AWG, solid conductor, shielded cable with 400 MHz bandwidth.

ATTENTION:

• Do not connect this connector to a computer data or telecommunications network.

• Ne connectez pas ces port à des données informatiques ou à un réseau de télécommunications.

Signal LED indicator — Lights when the device is transmitting a video signal or a test pattern.

Link LED indicator — Lights when a valid link between a DTP or HDBT input and output is established.

Step 4 — Mount the unit in the ﬂoor box

a. Place the DTP T FB unit in the desired position in the oor box so that the side panel connectors face

towards the opening of the oor box.

ATTENTION:

• Ensure there is enough space between the top panel connectors and the lid of the oor box so the lid fully closes.

• Assurez vous qu’il y ait assez d’espace entre les connecteurs du panneau supérieur et le couvercle du boîtier de sol an

que celui-ci puisse se fermer entièrement.

b. Using the provided self-threading screws, secure the DTP T FB unit to the adapter plates (see gures 2 through 5).

Ackermann GB3 (OBO Betterman) ﬂoor box

DTP T FB 332

POWER

DTP T FB 332

REMOTE

RS-232

- +

GRx Tx

12V

A MAX

XTP OUT

NOTE: For position 2, install

adapter plate 995242 to

one of the other adapter

plates.

995242 995241

Figure 2. DTP T FB Unit in an Ackermann GB3 (OBO Betterman) Floor Box

Power Supply

Output Cord

Ridges

Smooth

Captive

Screw

Connector

16 (5 mm) MAX

SECTION A–A

RxTx Gnd

RS-232 De

vice • 9600 Baud •

8 data bits

• No parity • 1 stop bit

REMOTE

RS-232

Rx Tx

16 (5 mm) MAX

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIAT

568B

TP Wires

12345678

Pins:

MK Electric CableLink Plus Single Pan ﬂoor box

DTPT FB 332

POWER

DTPT FB 332

REMOTE

RS-232

GRx Tx

12V

AMAX

POWER

DTPT FB 332

REMOTE

RS-232

12V

AMAX

995243

Figure 3. DTP T FB Unit in an MK Electric CableLink Plus Single Pan Floor Box

MK Electric CableLink Plus Modular ﬂoor box

DTPT FB 332

POWER

DTPT FB 332

REMOTE

RS-232

GRx Tx

12V

AMAX

XTP OUT

995244 995244

Figure 4. DTP T FB Unit in an MK Electric CableLink Plus Modular Floor Box

ElectraPlan or PUK ﬂoor box

DTPT FB 332

POWER

XTP T FB 202

REMOTE

RS-232

GRx Tx

12V

AMAX

XTP OUT

995300

Figure 5. DTP T FB Unit in an ElectraPlan (or PUK) Floor Box

Step 5 — Make side panel connections above the adapter plates

EHDMI input port (see ﬁgure 1 on page 1) — Connect an HDMI cable between this port and the HDMI output port of the digital video

source.

NOTE: See the LockIt®Lacing Brackets on page 4 of this guide to securely fasten the HDMI connector to the transmitter.

FVGA Input 1 port — Connect a VGA cable between this port and the VGA output port of the analog video source.

68-2682-50 Rev. B

11 17

DTP T FB 332 and DTP T FB 232 • Setup Guide (Continued)

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Australia

+61.8.8113.6800

+61.8.8351.2511 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

Step 6 — Make top panel connections

GAudio input (see ﬁgure 1 on page 1) — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog

audio input.

HRS-232 and IR connector — To pass serial or infrared data or control signals on the Over DTP RJ-45 output, connect the controlling

device to the transmitter via the RS-232 and IR captive screw connector. Connect the device to be controlled to the receiver.

IConfiguration port — Plug a PC or other controlling device into the switching transmitter via

this top panel mini-USB connector for remote conguration of the switching transmitter.

JReset button — This button initiates two levels of reset. See the DTP T FB 332 and

DTP T FB 232 User Guide, available at www.extron.com, for details.

Operation

After all connected devices are connected and powered on, the system is fully operational.

The DTP T FB unit can be congured and controlled using Extron Simple Instruction Set (SIS)

commands (see the DTP T FB 332 and DTP T FB 232 User Guide available at www.extron.com).

Indicators (K, see ﬁgure 1)

HDMI

VGA

HDCP

AUTO

Power LED —Lights when power is applied.

HDMI LED —Lights when the HDMI input signal is detected.

VGA LED —Lights when the VGA input signal is detected.

HDCP LED —Lights when the HDMI input signal is encrypted.

Auto LED —Lights when device is in auto switch mode. Auto switch is on by default.

When auto switch is on, the switcher automatically selects the input, HDMI or VGA, that has a valid signal present. When signals are

present on both inputs. the switcher selects VGA.

NOTE: Auto switch mode can be toggled off and on using the SIS commands. Issue the EnAUSW}SIS command,

where n= 0(off) or 1(on). The switcher responds with Auswn]. See the DTP T FB 332 and DTP T FB 232 User Guide,

available at www.extron.com, for details.

LockIt®Lacing Brackets

Use the included LockIt Lacing Brackets to securely fasten the HDMI cable as follows.

1. Plug the HDMI cable into the panel connection.

2. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt lacing

bracket to be placed over it. The screw does not have to be removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the

screw to secure the bracket.

ATTENTION:

•Do not overtighten the HDMI connector mounting screw. The shield it fastens to is very

thin and can easily be stripped.

•Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel elle est

attachée est très n et peut facilement être dénudé.

4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as

shown.

5. While holding the connector securely against the lacing bracket, use pliers or similar tools to tighten the tie wrap, then remove any

excess length.

TxRx

RxTx

Gnd

IR Device

RS-232 Device

RS-232 IR

Rx Tx

Tx Rx

OVER DTP

Dieses Handbuch passt für folgende Modelle

Andere Extron electronics Sender Handbücher

Extron electronics

Extron electronics DVI 201 A D Tx/Rx Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 101 D Bedienungsanleitung

Extron electronics

Extron electronics MTP T 15HD A Bedienungsanleitung

Extron electronics

Extron electronics A/V Receiver MTP 4T 15HD RS Bedienungsanleitung

Extron electronics

Extron electronics FOX II T HD 4K Bedienungsanleitung

Extron electronics

Extron electronics DTP T HWP D Series Bedienungsanleitung

Extron electronics

Extron electronics CAT 5 Bedienungsanleitung

Extron electronics

Extron electronics XTP T EU 202 Bedienungsanleitung

Extron electronics

Extron electronics MTP T 15HD A Bedienungsanleitung

Extron electronics

Extron electronics XTP FT HD 4K Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 330 Bedienungsanleitung

Extron electronics

Extron electronics XTP T FB 202 4K Bedienungsanleitung

Extron electronics

Extron electronics DTP2 T 202 FB Bedienungsanleitung

Extron electronics

Extron electronics XTP T FB 202 Bedienungsanleitung

Extron electronics

Extron electronics XTP T UWP 202 4K Bedienungsanleitung

Extron electronics

Extron electronics DTP T USW 333 Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 101 D Bedienungsanleitung

Extron electronics

Extron electronics DVI 201xi TX Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 230 Bedienungsanleitung

Extron electronics

Extron electronics DTP T USW 233 Bedienungsanleitung

Extron electronics

Extron electronics FOXBOX T HD-SDI Bedienungsanleitung

Extron electronics

Extron electronics FOX II T DP 4K Bedienungsanleitung

Extron electronics

Extron electronics DTP T DWP 4K D Series Bedienungsanleitung

Extron electronics

Extron electronics MTP U T A D Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung